• Journal of the Korean Ceramic Society
• /
• v.28 no.4
• /
• pp.261-268
• /
• 1991

The dielectric properties and microstructure of SrTiO3-based grain boundary layer (GBL) capacitor were investigated, and SrTiO3 GBL capacitor was made by penetrating the Frit (PbO-Bi2O3-B2O3 system). The Nb2O5-doped SrTiO3 ceramics were fired for 4-hours, at 145$0^{\circ}C$ in H2-N2 atomsphere to get semiconductive ceramics. The grain size of SrTiO3 sintered at reduction atmosphere had increased as the amount of Nb2O5 increases and then decreased as the amount of Nb2O5 exceeded 0.2 mole%. Insulating reagents which contained PbO-Bi2O3-B2O3 system frit and oxide mixture were printed on the each semiconductive ceramics and fired at varying temperature and for different holding time. The optimum dielectric properties could be obtained by second heat treatment at 110$0^{\circ}C$ for 1 hour, when frit paste was printed. A SrTiO3-based GBLC had the apparent permitivity of about 3.2$\times$104, the dielectric loss of 0.01~0.02 and the stable temperature coefficient of capacitance. The influence of frit paste on dielectric properties was similiar to that of oxide paste but the stability of temperature property of capacitance was improved.

• Journal of the Korean Ceramic Society
• /
• v.52 no.1
• /
• pp.28-32
• /
• 2015

In this article, the influence of a hydrolyzed wheat protein retarder on the hydration process, ion concentration in liquid phase, degree of supersaturation, and crystal morphology of plaster was investigated. Furthermore, the retarding mechanism and the strength loss of gypsum were also studied by scanning electron microscopy (SEM). The results indicate that the use of the hydrolyzed wheat protein retarder for plaster achieved a better retarding effect and lower strength loss. The combination of gypsum plaster with the retarder not only decreased the plaster's early hydration rate and prolonged its setting time efficiently, but also militated against the crystal morphology of dihydrate gypsum. For example, the crystal dimensions changed little, but the proportion of needle-shaped crystals decreased. Combination with calcium ions on the surface of dihydrate gypsum crystal nuclei may form a chemisorbed layer, reduce the surface energy of the crystal nuclei, and inhibit the growth of the crystal nuclei of dihydrate gypsum. Consequently, the hydration process of building gypsum becomes greatly extended and is slowed down significantly.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.166-174
• /
• 2014

This research investigated the aging properties of the $B-KNO_3$ system as the igniter. The $B-KNO_3$ system showed the degradation in ignition properties depending on the method and period of storage. It should be found out the cause of the degradation to predict the reliability of the igniters. The changes of the properties by the degradation after aging tests were analyzed by microstructure analysis, XRD analysis and thermal analysis using DSC. It was found out that the lattice parameters of the $KNO_3$ as the oxidizer in the ignition system was changed into the JCPDS values as the aging time increased. Conclusively, the changes of the crystal structure of oxidizer affected the activation energy increasing as aging time increased.

• Journal of Hydrogen and New Energy
• /
• v.16 no.2
• /
• pp.111-121
• /
• 2005

이 연구는 광화학적 물분해 수소제소 기술의 일환으로 수행 중인 광촉매와 바이오촉매를 복합한 시스템 활용 기술에서 광촉매가 갖는 물리적 특성의 영향을 파악하고자 진행되었다. 다양한 물리적 특성을 갖는 광촉매 얻기 위하여 상용광촉매, 수열화법(HT-TiON), 리고 저온합성법(LT-TiON) 등을 이용하여 샘플을 준비하였다. 가시광 감응을 위하여 암모니아나 triethylamine 처리를 하여 질소를 도핑도 시도하였다. 시도된 복합시스템은 인위적인 전자주개 없이 수소를 발생시키는 결과를 보여주었으나, 광촉매로부터 엔자임으로의 전자전달 부분이 율속단계로 확인되었다. 사용된 광촉매 샘플에 따라 수소발생량에 차이가 나타난 결과로 광촉매의 미세구조 (결정상, 결정도, 기공 크기 및 비표면적 등)이 중요한 역할을 하는 것으로 판단되었다. 얻어진 결과들을 활용하여 재료들이 고정화된 새로운 시스템 구성을 제안하였다.

• Journal of Hydrogen and New Energy
• /
• v.8 no.1
• /
• pp.11-21
• /
• 1997

$ZrV_{0.7}Mn_{0.5}Ni_{1.2}$ alloy is attractive for anode material in Ni/MH secondary battery because of its large hydrogen storage capacity in gas-solid reaction and long cycling durability in KOH electrolyte. In this work, in order to further improve the discharge performance of this alloy electrode, the alloy was annealed by optimal condition which is for 12 hours at $1000^{\circ}C$. The alloy annealed under optimal condition had higher rate capability and discharge capacity than as-cast one. The microstructure of the as-cast and annealed alloy was investigated by scanning electron microscopy and energy dispersive spectroscopy. Ni content in the matrix was increased, being this homogenized after annealing. Additionally, The measurement of the surface area by B.E.T. analysis showed that there was little difference as-cast and annealed alloy. Therefore, improvement in the rate capability of the annealed alloy is due to increase of Ni content in the matrix.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.298-305
• /
• 1995

Copper-indium diselenide, $CuInSe_2$, thin films have been fabricated by selenizing Cu/In stacked layers with different sputtered Cu/(Cu+ln) mole ratios at 450.deg. C for 1hr on alumina substrates. The selenium source was selenium vapor. Microstructure, crystallization, and composition of the selenized $CuInSe_2$ films were examined by using scanning electron microscope, X-ray diffraction, Auger electron spectroscopy, and secondary ion mass spectrometry. Electrical resistivity and hall effects were also measured to investigate the electrical properties. As the sputtered Cu/(Cu+In) mole ratio of In/Cu layer increased, the amounts of void and CuSe phase in the selenized films increased but the composition of $CuInSe_2$ phase was the same regardless of the sputtered mole ratio. Comparing the electrical properties of $CuInSe_2$ thin film before and after the chemical etching, it was seen that the electrical resistivity, carrier concentration, and carrier mobility of the selenized films were affected by the amount of CuSe phase which seemed to increase primarily the hole concentration of the selenized films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.477-480
• /
• 2004

Ga doped zinc oxide films (ZnO:Ga) were deposited on glass substrate by RF magnetron sputtering from a ZnO target mixed with $Ga_O_3$. The effects of RF discharge power on the electrical, optical and structural properties were investigated experimentally. The structural and electrical properties of the film are highly affected by the variation of RF discharge power. The lowest electrical resistivity of $4.9{\times}10^{-4}\;\Omega-cm$ were obtained with the film deposited from 3 wt% of $Ga_2O_3$ doped target and at 200 W in RF discharge power. The transmittance of the 900 nm thin film was 91.7% in the visible waves. The effect of annealing on the as-deposited film was also studied to improve the electrical resistivity of the ZnO:Ga film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.345-348
• /
• 2004

For practical applications, the evaluation of reliability or endurance of HTS conductors is necessary. The mechanical properties and the critical current, $I_c$, of multifilamentary Bi-2223 superconducting tapes, externally reinforced with stainless steel foils, subjected to high cycle fatigue loading in the longitudinal direction were investigated at 77K. The S-N curves were obtained and its transport property was evaluated with the increase of repeated cycles at different stress amplitudes. The effect of the stress ratio, R, on the $I_c$ degradation behavior under fatigue loading was also examined considering the practical application situation of HTS tapes. Microstructure observation was conducted in order to understand the L degradation mechanism in fatigued Bi-2223 tapes.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.608-614
• /
• 2003

Well developed hydroxyapatite whiskers (length 5 ${\mu}{\textrm}{m}$, diameter 0.5 ${\mu}{\textrm}{m}$) have been synthesized by the hydrolysis reaction of $\alpha$-tricalcium phosphate ($\alpha$-Ca$_3$(PO$_4$)$_2$) under pH 9.1 at 9$0^{\circ}C$ for 6 h. The effect of reaction conditions (temperature, time, pH) on the conversion of $\alpha$-tricalcium phosphate to hydroxyapatite was examined. In addition, the hydroryapatite was characterized in terms of microstructure, composition and thermal stability using XRD, SEM, ICP, and TGA instruments.

• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.406-412
• /
• 1997

Al2O3/SiC hybrid-composite has been fabricated by the conventional powder process. The addition of $\alpha$-Al2O3 as seed particles in the transformation of ${\gamma}$-Al2O3 to $\alpha$-Al2O3 provided a homogeneity of the microstructure. The grain growth of Al2O3 are significantly surpressed by the addition of nano-size SiC particles. Dislocation were produced due to the difference of thermal expansion coefficient between Al2O3 and SiC and piled up on SiC particles in Al2O3 matrix, resulting in transgranular fracture. The high fracture strength of the composite was contributed to the grain refinement and the transgranular fracture mode. The addition of SiC platelets to Al2O3/SiC nano-composite decreased the fracture strength, but increased the fracture toughness. Coated SiC platelets with nitrides such as BN and Si3N4 enhanced fracture toughness much more than non-coated SiC platelets by enhancing crack deflection.