• Journal of Korea Foundry Society
• /
• v.13 no.6
• /
• pp.540-546
• /
• 1993

The effects of fluid flow on the purification of aluminum were studied. As the revolution rate(N) increased, the size of columnar grain decreased gradually. The concentration of solidified crystal was decreased with increasing distance from chill and revolution rate(N). Distribution boundary layer thickness(${\delta}$) was calculated from the solute distribution obtained in solid experimentally and by use of BPS equation. The value of ${\delta}$ changed from about $60{\mu}m$ at N value of 27rpm to about $15{\mu}m$ at N value of 1000rpm. From this result, high purification was obtained by decreasing the diffusion boundary layer under forced convection.

• Journal of Korea Foundry Society
• /
• v.13 no.6
• /
• pp.555-562
• /
• 1993

A study was investgated the relationship between fracture characteristics and microstructure changes according to Cu addition and heat treatment methods on the ductile cast iron. According to increment of Cu addition pearlite volume fraction was increased due to the deffect of anti-ferritizing of Cu. At the case of austempering heat treatment, fracture toughness of Cu contained specimen was decreased. The reason for the results seems to be responsible for decrement of plastic zone size at the crack tip. It was observed that the excellent fracture toughness can be obtained at the condition of normalizing and the specimen was not contained Cu. Under the such conditions, fractographs is composed of dimple pattern and fracture toughness 71.6MPa $\sqrt{m}$, tensile strength determined as the value of 961.6MPa, respectively.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.146-148
• /
• 2003

SrZrO$_3$ resistive oxide barriers on Ag sheathed Bi2223 monocore tapes were prepared by the sol-gel and dip coating method to reduce AC coupling loss. The performance of the dip-coated SrZrO$_3$ thin films was evaluated in terms of bond strength and surface microstructure by varying the amount of PVP (polyvinylpyrrolidone) binder. Although bond strength and coating thickness increased as the PVP content rose, surface microcracking was more severe for the specimen containing higher content of PVP binder. It suggests that coating thickness and microcracking of the SrZrO$_3$ films on Bi2223 tapes was governed primarily by the amount of PVP binder.

• Journal of the Korean Ceramic Society
• /
• v.32 no.7
• /
• pp.846-852
• /
• 1995

The multiply reinforced mullite-zirconia composites were prepared with addition of Al2O3 particles, platelets, and fibers. The sinter-HIP specimens (presintered at 1$700^{\circ}C$ and hipped at 1$600^{\circ}C$) showed that the fracture toughness of Al2O3 fiber reinforcement (4.4 MPa.{{{{ SQRT {m} }}) was higher than those of platelet (4.0 MPa.{{{{ SQRT {m} }}) and of particle (3.9MPa.{{{{ SQRT {m} }}) reinforcement, whereas the fracture strength of Al2O3 particle reinforcement (304 MPa) was higher than those of platelet (293MPa) and of fiber (248MPa) reinforcement.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.387-393
• /
• 1998

The formation of titanium diboride ($TiB_2$ ) via the reduction of $TiO_2$ with boric oxide and carbon was studied in a partially reducing atmosphere of argon mixed with 4 vol.%H2. The effect of reaction time, temperature, partial pressure of nitrogen and $TiO_2/B_2_O3$ stoichiometric ratio on the reducibility of oxides has been studied. The phases formed were analysed by using X-ray rowder diffraction and scanning sosctron microscopic techniques. In this paper, we also investigated the presence of $CaC_2$ as a reducing agent on the reducibility of oxide mixtures and on the Ti-B-C-Ca-O phase equilibria. The morphology of $TiB_2$ formed in the presence of $CaC_2$ is compared with the microstructure of $TiB_2$ formed as a consequence of carbothermic reduction. The observed variation in $TiB_2$ crystals formed is also explained.

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.783-788
• /
• 1989

The reason of abnormal expansion in BaTiO3 synthesized in the equimolecular mixture and synthesized in Ba-rich region were investigated at the point of crystal and microstructure. The shrinkage and the expansion of the mixtures in BaCO3-TiO2 system were determined by the mass of BaCO3 added to the equimolecular BaCO3 and TiO2, Ba2TiO4 which was much formed and BaTi2O3 were important crystal in the reaction of Ba-rich region. Sintering phenomena of unreacted BaCO3 activity and the secondary phase caused to generate microcracks in the specimens.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1021-1029
• /
• 1994

SiC ultrafine particles of 1, 10, 20 and 30 vol% were dispersed in $\alpha$-Si3N4 matrix and hot-pressed under the condition of 30 MPa at 1800 and 190$0^{\circ}C$ respectively. Physical, mechanical properties and microstructures of sintered Si3N4-SiC nanocomposites were investigated. Flexural strength and density of Si3N4-10 vol% SiC nanocomposites hot-pressed at 190$0^{\circ}C$ represented the 1002 MPa and 97.9%T.D respectively, and it was confirmed as a remarkable improvement of 67% compared to Si3N4 monolith. Fracture toughness was shown as 7.2 MPa.m1/2 when the same composition was hot pressed at 180$0^{\circ}C$. This effect was supposed to be due to the improvement of microstructure by the adequate suppression of the excessive growth of Si3N4 grain with SiC nano-particles.

• Journal of the Korean Ceramic Society
• /
• v.33 no.2
• /
• pp.155-162
• /
• 1996

A Taguchi methodology study of the plasma spraying thermal barrier coating (TBC) layer is presented. The experiment parameters were designed by a L8-style orthogonal arrays approach. A Taguchi analysis was conduc-ted through the results of the coating properties which were affected by plasma spraying parameters. Zirconia (partially stbilized with ytrria: PSZ) was sprayed on TiAl intermetallic compound substrates, The coating layer was characterized by thickness microstructure and porosity using SEM and Image analyzer. The coating quali-ties are discussed with respect to thermal barrier effect thermal cycling test6 and adhesion strength test. An optimum condition of plasma spraying process which are derived from the Taguchi analysis could be found for high quality TBC.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.601-610
• /
• 1997

In cofiring of multilayered alumina with tungsten, the change of camber with lamination condition was experimented and the effect of sintering shrinkage of alumina and tungsten was investigated. From the exact measurement of sintering shrinkage of tungsten thick film, as lamination pressure increased, the sintering shrinkage of alumina decreased but that of tungsten thick film was not changed. So it was though that the main factor which induced the sintering shrinkage difference between ceramics and metal with lamination condition was the change of sintering shrinkage of ceramics. In case of high lamination pressure, high green sheet density, the cofired specimen showed low camber due to low shrinkage difference between alumina and tungsten and there was a linear relation between camber and shrinkage difference. It was found that this shrinkage difference could change the thickness of tungsten film and the microstructure within via hole during cofiring.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.05a
• /
• pp.198-201
• /
• 2006

To produce fine structure with uniform surface of barrier ribs in PDP, acid etching process has been used in manufacture process. It is necessary to understand the mechanism of etching, particularly on the interface of ceramic fillers and matrix glass. We investigated the effect of ceramic fillers (ZnO, $Al_{2}O_3$) on the microstructure of borate glass system to find an etching mechanism of barrier ribs. The harrier ribs was etched with a several steps, dissolving a small amount of residual glass, taking out alumina fillers, and removing a cluster type of ZnO fillers and glass matrix.