• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.2
• /
• pp.109-120
• /
• 1997

Microstructure and mechanical properties of Fe-Si-Mn-P high strength steel sheet have been investigated by controlling the cooling rate. Bainite and ferrite were obtatined by annealing in the ferrite pluse austenite region, and ferrite and austenite were obtatined after annealing in the fully austenite region. Ferrite and pearlite were obtained when the cooling rate was controlled from the annealing temperature above $760^{\circ}C$ and bainite showed with increasing cooling rate, however below $760^{\circ}C$ ferrite and bainite were obtained. Tensile strengths and hardness nearly unchanged with increasing cooling rate after control the cooling rate from the temperature above $760^{\circ}C$, while tensile strengths increased and elongation decreased with increasing cooling rate when the cooling rate was controlled from the tempeature below $760^{\circ}C$. Without regard to annealing temperature, tensile strength increased and elongation decreased with increasing cooling rate. Tensile strengths and elongation values heat treated in the ferrite plus austenite region were higher than those in the fully austenite region. Retained austenite and strength-elongation balance showed the maximum value at $780^{\circ}C$ and decreased with increasing annealing temperature. Strength-elongation balance value was controlled by the retained austenite.

• Korean Journal of Materials Research
• /
• v.16 no.4
• /
• pp.235-240
• /
• 2006

We investigated the effect of ZnO filler on the microstructure of $BaO-B_2O_3-ZnO-P_2O_5$ glass system to find an etching mechanism of barrier ribs. The sintering behavior of composites heated in the temperature range $560-600^{\circ}C$ was studied by volumetric shrinkage rate and microstructure. The etching test was carried out in $HNO_3$ solution at $50^{\circ}C$ for 10 min. The volumetric shrinkage of sintered sample decreased with the increased firing temperature because of the formation of two crystals. Glass and ZnO filler react forming the $BaZn_2(PO_4)_2$ crystal phases during the sintering process. Etching phenomenon of sintered samples by $HNO_3$ showed that the $BaZn_2(PO_4)_2$ crystal phase was strongly leached compared to glass matrix, crystal phases and fillers. Therefore, the control of interface by condition of sintering is so important to achieve etching effect in barrier ribs.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.129-129
• /
• 2018

Hard coating application is effective way of cutting tool for hard-to-machine materials such as Inconel, Ti and composite materials focused on high-tech industries which are widely employed in aerospace, automobile and the medical device industry also Information Technology. In cutting tool for hard-to-machine materials, high hardness is one of necessary condition along with high temperature stability and wear resistance. In recent years, high-entropy alloys (HEAs) which consist of five or more principal elements having an equi-atomic percentage were reported by Yeh. The main features of novel HEAs reveal thermodynamically stable, high strength, corrosion resistance and wear resistance by four characteristic features called high entropy, sluggish diffusion, several-lattice distortion and cocktail effect. It can be possible to significantly extend the field of application such as cutting tool for difficult-to-machine materials in extreme conditions. Base on this understanding, surface coatings using HEAs more recently have been developed with considerable interest due to their useful properties such as high hardness and phase transformation stability of high temperature. In present study, the nanocomposite coating layers with high hardness on WC substrate are investigated using high entropy alloy target made a powder metallurgy. Among the many surface coating methods, reactive magnetron sputtering is considered to be a proper process because of homogeneity of microstructure, improvement of productivity and simplicity of independent control for several critical deposition parameters. The N2 is applied to reactive gas to make nitride system with transition metals which is much harder than only alloy systems. The acceleration voltage from 100W to 300W is controlled by direct current power with various deposition times. The coating layers are systemically investigated by structural identification (XRD), evaluation of microstructure (FE-SEM, TEM) and mechanical properties (Nano-indenter).

• The Korean Journal of Food And Nutrition
• /
• v.31 no.1
• /
• pp.62-69
• /
• 2018

Pumpkin (Cucurbita moschata Duch.) seed is rich in protein and sulfur-containing amino acids. Tofu is a protein gel made from soybean, which is rich in lysine but lacking in sulfur-containing amino acids. This study was conducted to investigate the use of pumpkin seeds in tofu manufacture and to determine its quality and texture characteristics. Soybean was substituted with pumpkin seed to obtain pumpkin seed tofu at the following ratios: 10%, 30%, 50%, and 70% (P10, P30, P50 and P70). Tofu manufactured only with soybean was used as a control (Con). The higher rate of pumpkin seed substitution significantly decreased the moisture content and yield rate (p<0.05). In contrast, pH value and turbidity were significantly increased with the increase in the amount of pumpkin seed (p<0.05). The L-value (81.74~79.04), a-value (-0.19~-3.89) and b-value (12.40~9.84) of samples significantly decreased with the amount of pumpkin seed (p<0.05). No significant difference in syneresis was found among the samples (p<0.05). The hardness tended to decrease with the increase in the amount of pumpkin seed. The microstructure analysis revealed that the pore size of pumpkin seed tofu was smaller than that of Con. These results suggest that the pumpkin seed protein is a useful ingredient in the manufacture of tofu. Increasing the pumpkin seed substitution levels improves the texture of tofu.

• Journal of Welding and Joining
• /
• v.14 no.4
• /
• pp.99-108
• /
• 1996

The microstructure and bond strength are examined on the SiC/SiC and SiC/mild steel joints brazed by the Ag-Ti based alloys with different Ti contents. In the SiC/SiC brazed joints, the thickness of the reaction layers at the bond interface and the Ti particles in the brazing alloy matrices increase with Ti contents. When Ti is added up to 9 at% in the brazing alloy. $Ti_3SiC_2$ phase in addition to TiC and $Ti_5Si_3$ phase is newly created at the bond interface and TiAg phase is produced from peritectic reaction in the brazing alloy matrix. In the SiC/mild steel joints brazed with different Ti contents, the microstructure at the bond interface and in the brazing alloy matrix near SiC varies similarly to the case of SiC/SiC brazed joints. But, in the brazing alloy matrix near the mild steel, Fe-Ti intermetallic compounds are produced and increased with Ti contents. The bond strengths of the SiC/SiC and SiC/mild steel brazed joints are independent on Ti contents in the brazing alloy. There are no large differences of the bond strength between SiC/SiC and SiC/mild steel brazed joints. In the SiC/mild steel brazed joints, Fe dissolved from the mild steel does not affect on the bond strength of the joints. Thermal contraction of the mild steel has nearly no effects on the bond strength due to the wide brazing gap of specimens used in the four-point bend test. The brazed joints has the average bond strength of about 200 MPa independently on Ti contents, Fe dissolution and joint type. Fracture in four-point bend test initiates at the interface between SiC and TiC reaction layer and propagates through SiC bulk. The adhesive strength between SiC and TiC reaction layer seems to mainly control the bond strength of the brazed joints.

• Korean Journal of Materials Research
• /
• v.1 no.2
• /
• pp.65-70
• /
• 1991

The effect of inclusion particles on the microstructure development and electrical characteristics in the systems $ZnO-Bi_2O_3-CoO-Sb_2O_3\;and\;ZnO-Bi_2O_3-CoO-Sb_2O_3-Cr_2O_3 were investigated. The growth of ZnO grains, which was controlled by the spinel particles during sintering, decreased with increasing amount of spinel particles. Addition of $Cr_2O_3(0.5mol\%) increased the breakdown voltage without affecting the non-linear characteristics. The calculated barrier voltage of the $ZnO-Bi_2O_3-CoO-Sb_2O_3\;-and\;ZnO-Bi_2O_3-CoO-Sb_2O_3-Cr_2O_3$ systems were about 3.1V and 2.9V, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.417-421
• /
• 2018

$TiO_2$ has excellent photocatalytic properties and several studies have reported the increase in its specific surface area. The structure of $TiO_2$ nanofibers indicates promising improved photocatalytic properties and these nanofibers can thus potentially be applied in air pollution sensors and pollutant removal filters. In this study, a $TiO_2$ nanofiber was fabricated by the electrospinning method. The fabrication processing factors such as the applied voltage, the distance between nozzle and collector, and the inflow rate of solution were controlled. The precursor was titanium (IV) isopropoxide and as-spun $TiO_2$ nanofibers were heated at $450^{\circ}C$ for 2 h to obtain an anatase crystalline structure. The microstructure was analyzed using field emission scanning electron microscope (FE-SEM) and X-ray diffraction analysis (XRD). The anatase phase was observed in the $TiO_2$ nanofibers after heat treatment. The diameter of $TiO_2$ nanofibers increased with the flow rate, but decreased with decreasing applied voltage and nozzle to collector distance. The diameter of $TiO_2$ nanofibers was controlled in the range of 364 nm to 660 nm. These nanofibers are expected to be very useful in photocatalytic applications.

• Korean Journal of Materials Research
• /
• v.31 no.7
• /
• pp.409-419
• /
• 2021

The effect of solidification rate on micro-segregation in investment casting of IN738LC superalloy was studied. In Ni-based superalloys, the micro-segregation of solute atoms is formed due to limited diffusion during cast and solidification. The microstructure of cast Ni-based superalloys is largely divided into dendrite core of initial solidification and interdendrite of final solidification. In particular, mosaic shaped eutectic γ/γ' and carbides are formed in the interdendrite of the final solidification region in some cases. The micro-segregation phenomena formed in regions of dendrite core and interdendrite including eutectic γ/γ' and carbides were analyzed using OM, SEM/EDS and micro Vickers hardness. As a result of analysis, the lack of (Cr, W) and the accumulation of Ti were measured in the eutectic γ/γ', and the accumulation of (Cr, Mo) and the lack of Ti were measured in the interdendrite between dendrite and eutectic. Carbides formed in interdendritic region were composed of (Ti, W, Mo, C). The segregation applied to each microstructure is mainly due to the formation of γ' with Ni₃(Al,Ti) composition. The Ni accumulation accompanied by Cr depletion, and the Ti accumulated in the eutectic region as a γ' forming elements. The Mo tends to diffuse out from the dendrite core to the interdendrite, and the W diffuse out from the interdendrite to the dendrite core. Therefore, the accumulation of Mo in the interdendrite and the deficiency of W occur in the eutectic region located in the interdendrite. Heat treatment makes the degree of the micro-segregation decrease due to the diffusion during solid solution. This study could be applied to the heat treatment technology for the micro-segregation control in cast Ni-based superalloys.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.6
• /
• pp.258-263
• /
• 2021

ZnO varistor is a semiconductor device which can serve to protect the circuit from surge voltage because its non-linear I-V characteristics by controlling the microstructure of grain and grain boundaries. In order to obtain desired electrical properties, it is important to control microstructure evolution during the sintering process. In this research, we defined a dataset composed of process conditions of sintering and relative permittivity of sintered body, and collected experimental dataset with DOE. Meta-models can predict permittivity were developed by learning the collected experimental dataset on various machine learning algorithms. By utilizing the meta-model, we can derive optimized sintering conditions that could show the maximum permittivity from the numerical-based HMA (Hybrid Metaheuristic Algorithm) optimization algorithm. It is possible to search the optimal process conditions with minimum number of experiments if meta-model-based optimization is applied to ceramic processing.

• Journal of Chest Surgery
• /
• v.41 no.2
• /
• pp.177-188
• /
• 2008

Background: To evaluate the effects of inhaled nitric oxide (NO) and sphingosine 1-phosphate (S1P) as potential therapeutic agents of acute lung injury, we analyzed the morphology in vivo of the pulmonary microstructure using intravital videomicroscopy in a rat model of acute lung injury. Material and Method: Sprague Dawley rats were divided into five groups: a control group that underwent normal saline aspiration, an acute lung injury (ALI) group that underwent hydrochloric acid aspiration, and three treatment groups that underwent hydrochloric acid aspiration and were administered therapeutic agents- the S1P group, the NO group, and the S1P+NO group (n=7 per group). To quantify alveolar compliance and interstitial edema, the diameters of all measurable alveoli and interalveolar septa were averaged at one and two hours after aspiration. Alveolar compliance was determined according to diameter changes during the respiratory cycle and the change in tidal volume. Result: At two hours after aspiration, the mean alveolar compliance (% change) in the All group decreased significantly versus the control group of rats (respiratory cycle: 1.9% for the ALI group vs 6.5% for the control group, p=0.03; tidal volume: 3.2% for the ALI group vs 9.1% for the control group, p=0.003) and versus the NO group (tidal volume: 3.2% for the ALI group vs 16.9% for the NO group, p=0.001). At two hours after aspiration, the mean interalveolar septal thickness in the NO group tended to be smaller as compared to that in the All group ($15.2{\mu}m$ for the ALI group vs $12.3{\mu}m$ for the NO group, p=0.06). S1P did not exert a significant effect on the pulmonary microstructure of the injured rat lung. Conclusion: Improved alveolar compliance and reduced interstitial edema, observed by intravital videomicroscopy, suggest that inhaled NO ameliorates lung injury.