• 비파괴검사학회지
• /
• 제18권3호
• /
• pp.181-190
• /
• 1998

광원의 직경이 $5{\mu}m$ 수준인 X-선을 이용하여 미세 초점 X-선 단층촬영장치(computerized tomography system)를 제작하고 제어 및 계산 프로그램을 개발하였다. 본 장치는 비파괴검사용으로서 직경 20mm 이내의 시험체를 검사할 수 있다. 단층영상을 얻기 위한 계산 알고리즘으로서는 convolution back projection 알고리즘을 사용하였으며 광원의 형상을 평행 빔과 부채꼴 빔(fan beam) 등 두 종류를 사용하여 결과를 비교하였다. 장치의 제어 및 계산은 개인용 컴퓨터에서 동작하도록 하였다. 제작된 CT 장치와 프로그램을 이용하여 제작된 시편에 대하여 단층 영상을 복원하고 시편의 내부 구조 및 결함을 관찰하였다. 단층영상을 얻은 결과 실제 모습과 일치하는 재료내부의 결함에 대한 정보를 얻을 수 있었으며 해상도는 $20{\sim}30{\mu}m$정도인 것으로 판단되었다.

• 한국재료학회지
• /
• 제26권8호
• /
• pp.449-453
• /
• 2016

$HA(hydroxyapatite)/{\beta}-TCP$ (tricalcium phosphate) biomaterial (BCP; biphasic calcium phosphate) is widely used as bone cement or scaffolds material due to its superior biocompatibility. Furthermore, $NH_4HCO_3$ as a space holder (SH) has been used to evaluate feasibility assessment of porous structured BCP as bone scaffolds. In this study, using a spark plasma sintering (SPS) process at 393K and 1373K under 20MPa load, porous $HA/{\beta}-TCP$ biomaterials were successfully fabricated using $HA/{\beta}-TCP$ powders with 10~30 wt% SH, TiH2 as a foaming agent, and MgO powder as a binder. The effect of SH content on the pore size and distribution of the BCP biomaterial was observed by scanning electron microscopy (SEM) and a microfocus X-ray computer tomography system (SMX-225CT). The microstructure observations revealed that the volume fraction of the pores increased with increasing SH content and that rough pores were successfully fabricated by adding SH. Accordingly, the cell viabilities of BCP biomaterials were improved with increasing SH content. And, good biological properties were shown after assessment using Hanks balanced salt solution (HBSS).

• Journal of Chest Surgery
• /
• 제23권5호
• /
• pp.1003-1008
• /
• 1990

Primary choriocarcinoma of the lung is extremely rare and have been reported ten and several cases only in the literature. It is very difficult to confirm the "Pure primary pulmonary choriocarcinoma" clinically, so most cases that have been reported in the literature confirmed by autopsy and the prognosis is relatively poor compared with metastases. We experience one case of the primary pulmonary choriocarcinoma. She was 53 year old multiparous woman[4 \ulcorner0 \ulcorner2 \ulcorner0] who complain right chest pain for 4 years. On plain film and computerized tomogram of the thorax at admission, 2.5cmx3.5cmx5 cm sized, well demarcated ovoid mass was founded on the right middle lobe just below the parietal pleura and growing rapidly on plain film to 5cm x 6.5cm x 7cm after 15 days. We confirm the choriocarcinoma in the lung by percutaneous needle aspiration biopsy and strongly suspect primary after various examination for rule out metastases from the ovary or uterus. We perform middle lobe lobectomy because that can not confirm the primary or the metastases because there are not complete histological examination by bilateral ovariectomy and hysterectomy, and under the belief that extragestational or extragonadal primary choriocarcinoma is more resistant to the chemotherapy, and could be reduce the duration of hospitalization and the amount of chemotherapy used to achieve remission On 14th postoperative day, serum p-HCG level was returned to normal limit, and perform chemotherapy two times on 3rd and 5th week for prevention surgical traumatic hematogenous metastases or undetected microfocus, but the patient expire on 68th postoperative day due to intracerebral hemorrhage in the intracranial choriocarcinoma which strongly suspected surgical traumatic hematogenous metastases.etastases.

• 대한기계학회논문집A
• /
• 제38권4호
• /
• pp.409-417
• /
• 2014

구조물의 파괴는 주로 제조 과정에서 생긴 결함이나 사용 중 국부적인 손상의 원인으로 발생되는 균열에 의해 나타난다. 따라서 구조물이나 관련된 부품들의 균열 성장 과정을 분석하는 것은 구조물의 안정성 확보를 위하여 매우 중요하다. 본 논문에서는 균열의 성장을 분석하기 위해 노치가 있는 시편을 인장 실험하며, 마이크로 포커스 X-선 단층촬영을 이용하여 균열 성장을 관찰하였고, 노치가 있는 시편의 단층촬영의 영상으로부터 3 차원 재구축하여 만든 유한요소 모델과 이상적인 모양의 노치를 만든 유한요소 모델을 XFEM에 적용하여 3 차원 균열 성장의 시뮬레이션을 실시 하였다. 실제 시편의 인장 실험 결과와 시뮬레이션 실험들의 결과를 비교하였고, 보다 정밀한 3 차원적 균열 성장의 분석을 위해서는 실제적인 구조물 및 균열의 형태에 대한 3 차원 모델링이 반드시 실시되어야 함을 확인하였다.

• 한국재료학회지
• /
• 제25권4호
• /
• pp.165-170
• /
• 2015

Ceramics biomaterials are useful as implant materials in orthopedic surgery. In this study, porous HA(hydroxyapatite)/${\beta}$-TCP(tricalcium phosphate) composite biomaterials were successfully fabricated using HA/${\beta}$-TCP powders with 10-30 wt% $NH_4HCO_3$ as a space holder(SH) and $TiH_2$ as a foaming agent, and MgO powder as a binder. The HA/${\beta}$-TCP powders were consolidated by spark plasma sintering(SPS) process at $1000^{\circ}C$ under 20 MPa conditions. The effect of SH content on the pore size and distribution of the HA/${\beta}$-TCP composite was observed by scanning electron microscopy(SEM) and a microfocus X-ray computer tomography system(SMX-225CT). These microstructure observations revealed that the volume fraction of the pores increased with increasing SH content. The pore size of the HA/${\beta}$-TCP composites is about $400-500{\mu}m$. The relative density of the porous HA/${\beta}$-TCP composite increased with decreasing SH content. The porous HA/${\beta}$-TCP composite fabricated with 30%SH exhibited an elastic modulus similar to that of cortical bone; however, the compression strength of this composite is higher than that of cortical bone.

• Restorative Dentistry and Endodontics
• /
• 제28권6호
• /
• pp.485-490
• /
• 2003

Complete understanding of the exterior and interior structure of the tooth would be prerequisite to the successful clinical results, especially in the restorative and endodontic treatment. Although three-dimensional reconstruction method using x-ray microtomography could not be used in clinical cases, it may be the best way to reconstruct the morphologic characteristics of the tooth structure in detail without destructing the tooth itself. This study was done to three dimensionally reconstruct every teeth in the arch in order to increase the understanding about the endodontic treatment and to promote the effective restorative treatment by upgrading the knowledge of the tooth morphology. After placing tooth between the microfocus x-ray tube and the image intensifier to obtain two-dimensional images of each level. scanning was done under the condition of 80 keV, $100{\;}\mu\textrm{m}$, 16.8 magnification with the spot size of $8{\;}\mu\textrm{m}$. Cross-section pixel size of $16.28{\;}\mu\textrm{m}$ and 48.83 cross-section to cross-section distance were also used. From the results of this study, precise three dimensional reconstructed images of every teeth could be obtained. Furthermore, it was possible to see image that showed interested area only, for example. enamel portion only, pulp and dentin area without enamel structure, pulp only, combination image of enamel and pulp, etc. It was also possible to see transparent image without some part of tooth structure. This image might be used as a guide when restoring and preparing the full and partial crown by showing the positional and morphological relationship between the pulp and the outer tooth structure. Another profit may be related with the fact that it would promote the understanding of the interior structure by making observation of the auto-rotating image of AVI file from the various direction possible.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.73-73
• /
• 2009

In this sutdy, a new class ACA(Anisotropic Conductive Adhesive) with low-melting-point alloy(LMPA) and self-organized interconnection method were developed. This developed self-organized interconnection method are achieved by the flow, melting, coalescence and wetting characteristics of the LMPA fillers in ACA. In order to observe self-interconnection characteristic, the QFP($14{\times}14{\times}2.7mm$ size and 1mm lead pitch) was used. Thermal characteristic of the ACA and temperature-dependant viscosity characteristics of the polymer were observed by differential scanning calorimetry(DSC) and torsional parallel rheometer, respectively. A electrical and mechanical characteristics of QFP bonding were measured using multimeter and pull tester, respectively. Wetting and coalescence characteristics of LMPA filler particles and morphology of conduction path were observed by microfocus X-ray inspection systems and cross-sectional optical microscope. As a result, the developed self-organized interconnection method has a good electrical characteristic($2.41m{\Omega}$) and bonding strength(17.19N) by metallurgical interconnection of molten solder particles in ACA.

• 한국의학물리학회지:의학물리
• /
• 제26권4호
• /
• pp.215-222
• /
• 2015

본 연구에서는 단일 비산란 그리드 및 다색광 x-선원을 이용하여 위상대조 x-선 영상을 용이하게 구현할 수 있는 새로운 방법을 제안한다. 제안된 신기법의 개념 입증을 위해 집속형 선형 그리드(200 lines/inch 선 밀도), 마이크로 초점 x-선관(${\sim}5{\mu}m$ 초점크기), CMOS형 평판형 검출기($48{\mu}m$ 픽셀 크기)로 실험장치를 구성하였으며, 한 번의 x-선 촬영($90kV_p$, 0.1 mAs)으로 감약대조 x-선 영상과 향상된 가시성을 지진 산란 x-선 영상 및 차분 위상대조 x-선 영상을 Fourier변조복원 기법을 적용하여 성공적으로 분리 획득하였다. 더 나아가, 감약대조 x-선 영상과 산란 x-선 영상을 합성함으로써 일반 감약대조 x-선 영상에서는 명확하게 볼 수 없는 샘플의 미세 구조를 보다 선명하게 나타냄을 확인하였다. 본 논문에서 제안한 단일 비산란 그리드 기반 위상대조 x-선 영상화 기법은 실험 구성 및 절차가 단순하고 새로운 대조도에 기반한 산란 및 위상대조 x-선 영상을 동시에 제공하기 때문에 차세대 x-선 영상화 신기법으로 다양한 응용분야에서 용이하게 적용될 수 있을 것으로 전망한다.