• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.9
• /
• pp.848-852
• /
• 2008

Characteristics of microcrystalline-silicon thin-films deposited by plasma-enhanced chemical-vapor deposition (PECVD) method were studied. There were optimum values of RF power density and $H_2$ dilution ratio $(H_2/(SiH_4+H_2))$; maximum grain size of about 35 nm was obtained at substrate temperature of 250 $^{\circ}C$ with RF power density of 1.1 W/$cm^2$ and $H_2$ dilution ratio of 0.91. Larger grain was obtained with higher substrate temperature up to 350 $^{\circ}C$. Grain size dependence on RF power density and $H_2$ dilution ratio could be explained by etching effects of hydrogen ions and changes of species of reactive precursors on growing surface. Surface-mobility activation of reactive precursors by temperature could be a reason of grain-size dependence on the substrate temperature. Microcrystalline-silicon thin-films that could be used for flat-panel electronics such as active-matrix organic-light-emitting-diodes are expected to be fabricated successfully using these results.

• Journal of Pharmaceutical Investigation
• /
• v.38 no.3
• /
• pp.157-162
• /
• 2008

The aim of the study was to formulate the stable amlodipine maleate tablet by selecting and combining of suitable ingredients. Amlodipine tablets were designed by using different manufacturing methods or formulations. Dissolution rate at 30 min of newly formulated tablets was over 98% in 0.1 M HCl medium. After 4 months storage under accelerated condition, the changes of appearance, loss on drying, content and total impurity were investigated. For long-term stability tests, two formulations of K017 (direct compressed tablets consisting of microcrystalline cellulose and pregelatinized starch) and K018 (wet granulated tablets by OpadryAMB) were stored under $25^{\circ}C$, 60% RH for 24 months. Under the accelerated condition, moisture content in K017 formulation was increased as 5.96% for 4 months, while other formulations with anhydrous monobasic phosphoric potassium or by wet granulation showed higher increase in moisture content compared to K017. In addition, K017 formulation showed a low decrease in contents and total relative substance as 0.8% and 0.7%, respectively. Similar stability of amlodipine in K017 was obtained under the long-term stability test. These results indicate that the K017 combined with microcrystalline cellulose and pregelatinized starch as ingredients is very stable formulation to protect active substance from moisture contact and sustain stability. Therefore, suitable combination of ingredients such as microcrystalline cellulose and pregelatinized starch could attribute to enhance the stability of moisture-labile drug such as amlodipine maleate.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.57-58
• /
• 2008

Microcrystalline (${\mu}c$) silicon thin films were prepared on glass by plasma-enhanced-chemical-vapor-deposition (PECVD) at various substrate temperature, and dilution ratio of $H_2$ with $SiH_4$. The structural and optical properties of. the ${\mu}c-Si$ thin films were investigated using XRD and UV-VIS spectrophotometer. The ${\mu}c-Si$ thin film with 42 nm grain size was grown at optimal condition of 2.5 Torr, spacing between electrodes of 3cm, deposition time of 3000s, RF power of 200W, substrate temperature of $350^{\circ}C$, $SiH_4$ ($20%SiH_4$+80%He) of 50sccm, and $H_2$ of 100sccm.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.197-199
• /
• 2011

In this paper, the bottom-gate thin-film transistors (TFTs) were fabricated with an amorphous/microcrystalline Si double layer (DL) as an active layer and the variations of the electrical characteristics were investigated according to the DC bias stresses. Since the fabrication process of DL TFTs was identical to that of the conventional amorphous Si (a-Si) TFTs, it creates no additional manufacturing cost. Moreover, the amorphous/microcrystalline Si DL could possibly improve stability and mass production efficiency. Although the field effect mobility of the typical DL TFTs is similar to that of a-Si TFTs, the DL TFTs had a higher reliability with respect to the direct current (DC) bias stresses.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.64.2-64.2
• /
• 2011

Recently, Silicon Germanium (SiGe) alloys have been received considerable attention for their great potentials in advanced electronic and optoelectronic devices. Especially, microcrystalline SiGe is a good channel material for thin film transistor due to its advantages such as narrow and variable band gap and process compatibility with Si based integrated circuits. In this work, microcrystalline silicon-germanium films (${\mu}c$-SiGe) were deposited by DC/RF magnetron co-sputtering method using Si and Ge target on Corning glass substrates. The film composition was controlled by changing DC and RF powers applied to each target. The substrate temperatures were changed from $100^{\circ}C$ to $450^{\circ}C$. The microstructure of the thin films was analyzed by x-ray diffraction (XRD) and Raman spectroscopy. The analysis results showed that the crystallinity of the films enhances with increasing Ge mole fraction. Also, crystallization temperature was reduced to $300^{\circ}C$ with $H_2$ dilution. Hall measurements indicated that the electrical properties were improved by Ge alloying.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.218-221
• /
• 2008

Bottom-gate microcrystalline silicon thin film transistors (${\mu}c$-Si:H TFTs) were fabricated on glass and transparent polyimide substrates by conventional 13.56 MHz RF plasma enhanced chemical vapor deposition at $200^{\circ}C$. The deposition rate of the ${\mu}c$-Si:H film is 24 nm/min and the amorphous incubation layer near the ${\mu}c$-Si:H/silicon nitride interface is unobvious. The threshold voltage of ${\mu}c$-Si:H TFTs can be improved by $H_2$ or $NH_3$ plasma pretreatment silicon nitride film.

• YAKHAK HOEJI
• /
• v.18 no.4
• /
• pp.236-242
• /
• 1974

Extrusion-spheronization processing combination was used to produce spherical granules with experimental formulations which contain microcrystalline cellulose as a diluent. The produced granules were compared on the basis of the following physical properties ; (a) bulk density, (e) porosity, (f) friabillity and (g) dissolution rate. With the specific experimental formulations used in this study, the increased plate rotational speeds of Marumerizer (400-1200rpm) produced continually more spherical material and also the obtained data indicated that the particle size distribution and dissolution rate depend upon the amount of microcrystalline cellulose used. As a result, the spherical granule preparation with microcrystalline cellulose has good properties in flow rate, packing propertyu and friability and offers a suitable method of granule preparation in pharmaceutical industry.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1B
• /
• pp.107-111
• /
• 2006

The samples collected from two reactors are analyzed by X-ray diffraction and M$\ddot{o}$ssbauer spectroscopy in this study. It is concluded that the iron oxide crystal attached on anthracite media which possesses catalytic ability is identified to be Ferrihydrite, regardless of the value of pH from the analysis of the iron oxide. Iron oxide in Batch reactor is identified to be Microcrystalline goethite.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.1
• /
• pp.45-50
• /
• 1992

To utilize shellfish by-products effectively, chitin, chitosan, and microcrystalline chitin were prepared from 6 kinds of crustacean shells(Antarctic krill, Euphausia superba; Red snow crab, Chinonecetes japonicus: Daelongsuyum shrimp, Solenocera prominentis: Lobster, Linuparus trigonus: Gasibal shrimp, Nephrops thomsoni: Blue crab, Portunus trituberculatus) and their functional properties were studied. Apparent volume(AV), settling volume(SV), water binding capacity(WBC), and fat binding capacity(FBC) of various chitins, chitosans, and microcrystalline chitins ranged from $3.1\pm0.1ml/g\;to\;27.0\pm0.2ml/g$ from $5.1\pm0.1ml/g\;to\;45.0\pm0.2ml/g,\;from\;318\pm40g/100g\;to\;2,382\pm12g/100g,\;and\;from\;235\pm20g/100g\;to\;2,169\pm20g/100g$, respectively, and the krill chitin and chitosan had the highest AV, SV, WBC, and FBC of them. Chitins and chitosans did not produce emulsion but microcrystalline chitins showed emulsifying properties. Emulsifying capacity and stability of various microcrystalline chitins ranged from $18.2\pm4.0\%\;to\;50.1\pm2.5\%\;and\;from\;15.2\pm3.5\%\;to\;31.1\pm1.0\%$, respectively. Dye binding capacity of microcrystalline chitins was higher than that of chitins or chitosans.

• Journal of Conservation Science
• /
• v.25 no.4
• /
• pp.373-381
• /
• 2009

To preserve steel cultural properties on display outdoors, the surface of these relics is processed with a covering treatment, which is a typical anti-corrosion method. Since the registered cultural heritage of Korea No. 78 Locomotive at Jangdan Station of Gyeongui Line will be treated by preservation process and displayed in the open outdoor area, effective surface covering agents were selected through testing to prevent the corrosion of the locomotive. The mixed wax are based on two types of microcrystalline wax which is one of regular surface covering agents for locomotives and bee‘s wax. For the weather resistance test, 3 types of wax were applied to each specimen of the locomotive and the specimens were tested in the Xenon-Arc Accelerated Weathering Tester for 1000 hours in accordance with the ISO 4892-1981 criteria and the test results were compared. As a result, on the surface of the specimen coated with the bee's wax, a whitening event appears after 400 hours which causes aging, and the specimens coated by the microcrystalline wax showed signs of a whitening event after 800 hours. The moisture contact angle with the microcrystalline wax coating was also less than with the bee's wax. Therefore, it was found that the high temperature microcrystalline wax is the most effective coating agent in terms of weather resistance and moisture blocking capability and the high temperature microcrystalline wax was adopted for coating the surface of the locomotive.