• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.68-75
• /
• 2000

This paper presents the construction of an ultra-precision machining system and machining experiments using the developed system. The system is composed of air bearing system, granite bed, air pad, and linear feeding mechanism. The cutting conditions have great effect on the surface quality in ultra-precision machining. the ultra-precision machining is mainly processed by several ${\mu}{\textrm}{m}$ depth of cut and feed rate. For this, tools with sharper cutting edge and less tool wear are needed. To satisfy these requirement, diamond is generally used as a tool material for ultra-precision machining. In order to evaluate the cutting characteristics of the PCD and MCD tools on the aluminum alloy, the machining experiments performed using the developed system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1456-1464
• /
• 1993

The achievable machining accuracy depends upon the level of the micro-engineering, and the dimensional tolerances in the order of 10 nm and surface roughness in the order of 1 nm are the accuracy targets to achieved today. Such requirements cannot be satisfied by the conventional machining processes. Single point diamond turning is one of the new techniques which can produce the parts with such accuracy limits. The aims of this thesis are to get a better understanding of the complex cutting forces. A cutting model for describing the influence of cutting conditions (cutting speed, feedrate and depth of cut), material properties of the workpiece and tool geometry has been proposed after estimating the two cutting force models-the Recht model and the Dautzenberg model. The experiments with Al-alloy workpieces, which have been carried out in order to estimate the models, show that the proposed model in this thesis is better than the two models. As the depth of cut and feedrate are increased in the operations settings (depth of cut 8-100$\mu{m}$, feedrate 8-140$\mu{m}$/rev, and cutting speed 8 m/sec), the relation of dimensionless cutting forces from experiments are similar to the proposed model. With the undeformed chip area of $30-80{\times}10^{2}$\mu{m}^2$, the experimental cutting forces accord with the force prediction.

• Journal of Biosystems Engineering
• /
• v.13 no.2
• /
• pp.38-45
• /
• 1988

This study was intended to develop the system automatically controlling travel direction of combine by means of sensing paddy rows. The control system was composed of three detecting levers having different length, micro-switch, microcomputer and electro-hydraulic control system. Sensor and control system developed was tested to estimate optimum design values and its actual performance as installed in combine. The computer simulation and performance test at simulated and actual field were conducted to test for possibility of practical use. The results of the study arc summarized. as follows: 1. The travel traces of combine hiving the conventional sensor with 2 levers and the new sensor detecting the slope of paddy rows were compared through computer simulation. Turning frequency of combine having new sensor was fewer than that of conventional sensor, but the rate of turning for the combine with new sensor was much greater than that of conventional sensor. 2. As sensor was established behind the tip of divider, the sensor itself well followed paddy rows but the tip of divider did not, resulting in divider being deviated from paddy rows. It was analyzed that the sensor should be attached closer to the tip of divider to have a better performance of the control system. 3. The greater the length of sensor lever for given location of sensor attachment and combine forward speed, the higher sensitivity of turning in control system. Moreover, increasing combine speed resulted in a worse performance of control system following paddy rows. Consequently, it was necessary that an optimum length of sensor attachment and for the range of combine operational speed. 4. Field test of combine installed with the sensor and electro-hydraulic system developed in this study showed that it may be operated smoothly and well behaved to paddy rows to 4th gear of combine speed which was 59cm/s. Consequently. it was concluded that the combine with the guidance control system developed in this study may be successfully used for paddy combining.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.818-821
• /
• 2004

With a rapid development in the area of micro and ultra precision technology, the micro surface machining of small size parts are explosively increased. Especially, to improve efficiency of various beams in lens and reflector, non-rotational symmetric form and several mm level heights changeable surface can be machined at a time. These geometric complex 3D surface cannot be machined by general short stroke FTS. The long stroke FTS if firmly needed to move directly several mm and have nm level positioning accuracy for the complex surface form. The long stroke FTS used linear motors to drive moving unit long and fine, aero static bearings to decrease friction and moving errors in guide way, optical linear scale with nm level resolution to measure position of FTS. Furthermore, to increase the performance of acceleration of FTS, the light material, such as AL is used for the structure and the high stiffness box type structure is selected. In this paper, the genetic algorithm approach is described to determine a set of design parameters for auto tuning. The authors have attempted to model the design problem with the objective of minimizing the error, such as variable pattern change. This method can give the better alternative than existing other method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.7
• /
• pp.535-540
• /
• 2009

Experiments are conducted to elucidate effects of counterflow burner diameter on flame extinction behaviors in C-curve. Present experimental results with burner diameters of 18, 26, and 50 mm in normal-gravity are compared with the numerical result of Oppdif code as well as the previous experimental results in micro-gravity. The turning point migrates to a higher global strain rate as burner diameter decreases. It is shown that the C-curve with the burner diameter of 50mm is best-fitted to the numerical result of Oppdif code and the previous micro-gravity results also excurse to the numerical result. This suggests that the precise C-curve can be obtained only with an appreciably large burner. The main reason why these differences appear is shown to be attributed to the transition of shrinking flame disk to flame hole due to strong effects of radial conduction heat loss, which is the typical extinction characteristics of low strain rate flames with a finite burner diameter in a counterflow diffusion flame.

• Journal of Korean Society of Transportation
• /
• v.19 no.6
• /
• pp.143-160
• /
• 2001

Micro-simulation models have been recognized as an efficient assessment tool in developing traffic signal control technologies. In this paper a prototype of a microscopic simulation model which can be applied to evaluate the performance of traffic-adaptive signal control strategies was developed. In the simulation process, space-based arrays were appled to estimate parameters of car following and lane changing models. Two levels of link types, a micro-type and macro-type links, were also embodied in the simulation process. The proposed model was tested on a test network consists of 9 intersections. The performance of the proposed model was evaluated in link by link comparisons with the results of NETSIM. The results show that the proposed model could appropriately simulate traffic flows of the test network. The model also produces traffic adaptive signal timings, cycle lengths and green times for turning movements, based on the detector data. It implies that the optimization process of the model produces reasonable signal timings for the test network on the cycle basis.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.956-961
• /
• 2004

This paper proposes a study on the spherical lens manufacturing by simultaneous 3 axis for NC lathe. We use friction drive system for moving system in experimental diamond turing machine. The diamond turning machine use manufacturing for high quality lens, mirror and many optics products. Especially, the high tech industry require a lot of lens. For example, optical engineering. medical science, space engineering and material engineering etc. The friction drive system is very simple and quiet, compared to ball screw system. We find a problem at the simultaneous 3 axis and suggest a solution. Also, when we manufactured a micro lens. find a problem and solution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.102-107
• /
• 1993

The achievable machining accuracy depends upon the level of the micro-engineering, and the dimensional tolerances in the order of 10nm and surface roughness in the order of 1nm are the accuracytargets to be achieved today. Suchrequirements cannot be satisfiedby the conventional machining processes. Single point diamond turning is one of the new techniques which can produce the parts with such accuracy limits. The aims of this thesis are to get a better understanding of the complex cutting process with a diamond tool and, consequently, to develope a predicting modelof a turned surface profile. In order to predict the turned surface profile, a numerical model has been developed. By means of this model, the influences of the cutting conditions, the material properties of the workpiece, the geometry of the cutting tool and the dynamic behaviour of the lathe and their influences via the cutting forces upon the surface roughness have been estimated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.115-120
• /
• 1992

Mirror-surface machining is very important machining technology to manufacture optical parts. especially brittle materials. In case of optical plastics, it is produced through both grinding and polishing till now. New machining method which is more efficient and contributed to the protection of the environmental pollution is, therefore, studied. In this , experimental results and an analysis of surface roughness in ultrasonic vibration cutting of optical plastic (CR-39) which is used for optical lens is presented. In results, a comparison of the micro-structure of machined surfaces produced by cutting with ultrasonic vibration and conventional turning is presented by analyzing S.E.M. photograph. Also, wavelength spectrum analysis is performed to investigate the surface-characteristics machined by ultrasonic vibration cutting.

• Journal of Korean Vacuum Science & Technology
• /
• v.3 no.1
• /
• pp.10-15
• /
• 1999

Using micro-wells on the Mo substrate, we could obtain various tubular-volcano-types of free-standing diamond field emitters by depositing a diamond film detaching the film and turning the film upside down. The field emission characteristics of these structures were investigated as a function of size, shape and the number density of the tubular-volcano-type diamond field emitters. The field emission characteristics, especially the current density, were greatly enhanced with increasing the number density of the tubular-volcano-type diamond field emitters on the Mo substrate. Based on these results, we suggest that the reduction of the well size can give better field emission characteristics by the increase in the number density of the tubular-volcano-type diamond field emitters. Finally, we suggest the feasibility of fabricating a large-area field emission display using our patterned tubular-volcano-type free-standing diamond field emitters.