• 한국유체기계학회 논문집
• /
• 제16권3호
• /
• pp.18-25
• /
• 2013

Recently the requirement of long-term mobile energy source for mobile robot or small-sized unmanned vehicle is highly increased, and the micro turbine generator(MTG) which is known to have high energy and power density is under development. MTG is designed to have air foil bearing and high speed rotor of which operating speed is 400,000rpm. In the development stage of high speed rotor and bearing, stability analysis for the full operational speed range is essential and the dynamic coefficients such as stiffness and damping coefficients of bearing depending on the rotational speed are required for that. Although perturbation method is usually used to identify the dynamic coefficients, it's not easy to give the perturbation to the high speed rotating rotor. In this study, we present the dynamic coefficients measurement system for air foil bearing which consists of electromagnets, gap sensors, high speed motor and controller. This measurement system can exert the sine sweep force to the rotor-bearing, measure the displacement of rotor and get FRF(Frequency response function) of rotor-bearing. The least square estimation method is applied to identify the dynamic coefficients of bearing from the measured frequency response at the different rpm and the identified dynamic coefficients for the wide rotational speed range are presented.

• Nuclear Engineering and Technology
• /
• 제33권2호
• /
• pp.145-155
• /
• 2001

This simulation first allows us to define a transition zone from a bubble to jet mode of the argon out-flow and hereinafter to define a similar area for water-steam leak in the KALIMER SG (Korea Advanced Liquid Metal Reactor Steam Generator) using a water mock-up system, taking into account the KALIMER leak classification and tube bundle design, as a simulation of a real water-steam into sodium leak. in accordance with leak conditions in the KALIMER SG, the transition from bubbling to jetting is studied by means of turbulence regime simulation for argon out-flow through a very small orifice, which has the equivalent diameter of about 0.253 mm. finally the noise generation mechanism is explained from the existing experimental data. We also confirmed the possibility of micro-leak detection from the information of the bubbling mode through simulations and the experiment in this study.

• 전기학회논문지P
• /
• 제64권1호
• /
• pp.7-13
• /
• 2015

This paper presents mathematical models for high speed permanent-magnet synchronous machine. The mathematical method with two successive steps is used to estimate design parameter as well as the output power. At first, mathematical model for a linkage flux problem is employed to calculate the number of winding turns and stack length of armature core. The magnetic circuit model for an induced voltage and the electric circuit model for a current are modeled. The output powers of the electrical generator were evaluated by the mathematical techniques. The results of this mathematical methods predict the specifications of the machine and can be applied in the design stage of the electrical machine.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.264-266
• /
• 2005

Recently, on-line diagnosis methods through wired and wireless networks are widely adopted in the diagnosis of industrial Electric Facilities, such as generators, transformers and motors. Also smart sensors which includes sensors, signal conditioning circuits and micro-controller in one board are widely studied in the field of condition monitoring. This paper suggests an self-powered system suitable for condition-monitoring smart sensors, which uses parasitic vibrations of the facilities as energy source. First, vibration-driven noise patterns of the electric facilities are presented. And then, an electromagnetic generator which uses mechanical mass-spring vibration resonance are suggested and designed. Finally energy consumption of the presented smart sensor, which consists of MEMS vibration sensors, signal conditioning circuits, a low-power consumption micro-controller, and a ZIGBEE wireless tranceiver, are presented. The usefulness and limits of the presented electromagnetic generators in the field of electric facility monitoring are also suggested.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.361-366
• /
• 2001

A mim turbo-shaft engine of 50HP for UAV, which can be easily modified to turbo-prop and turbo-jet engine by sharing the core engine and has many applications to civilian demands and munitions, will be developed This kind of micro gas turbine engine has been developed mostly by the corporations which have special technology but are small in its scale. Especially, the gas turbine engine can be easily applied to other fields and developed by domestic technology, so that the sharing of technology is planed to realize through the cooperations with academies and research institutes. In this paper, the gas turbine engine, which has the compressor ratio of 3.8, the turbine inlet temperature of l180K and the engine speed higher than 100,000 rpm, is composed of centrifugal compressor, combustor, gas generator turbine, free power turbine and gear box. The competitiveness of the gas turbine engine can be obtained from minimizing its cost by the utilization of domestic infrastructure for the performance test and the decisive outsourcing.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권4호
• /
• pp.383-390
• /
• 2014

This paper presents an excitatory CMOS neuron oscillator circuit design, which can synchronize two neuron-bursting patterns. The excitatory CMOS neuron oscillator is composed of CMOS neurons and CMOS excitatory synapses. And the neurons and synapses are connected into a close loop. The CMOS neuron is based on the Hindmarsh-Rose (HR) neuron model and excitatory synapse is based on the chemical synapse model. In order to fabricate using a 0.18 um CMOS standard process technology with 1.8V compatible transistors, both time and amplitude scaling of HR neuron model is adopted. This full-chip integration minimizes the power consumption and circuit size, which is ideal for motion control unit of the proposed bio-mimetic micro-robot. The experimental results demonstrate that the proposed excitatory CMOS neuron oscillator performs the expected waveforms with scaled time and amplitude. The active silicon area of the fabricated chip is $1.1mm^2$ including I/O pads.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.142-142
• /
• 2007

Micro thermoelectric generator has been attractive for the alternative power source to operate the wireless sensor node. In this paper, we designed the column-type micro thermoelectric device and their device characteristics were measured. n-type Bi2Te3 and p-type BiSbTe3 thermoelectric thin films were grown on (001) GaAs substrates by metal organic chemical vapour deposition (MOCVD) and they were pattemed. The height of thermoelectric film were controlled by the deposition time, temperature and MO-x gas pressure. Seebeck coefficient was measured at room temperature and hole concentration and electrical resistivity of thermoelectric film were also characterized.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권6호
• /
• pp.316-323
• /
• 2004

This paper develops an ADWHM(Advanced Digital Watt-Hour Meter) which integrates and implements the voltage management data record function and the load management data record function in the electronic watt-hour meter. ADWHM is developed based on PIC16F874 which is 8bit micro-controller of RISK type for the easy of programing and maintenance, and electronic power signal processing module is located at front of it to reduce the computing load of processor. Also, a 16kbyte EEPROM is used to record the voltage management data and load management data for a week as well as watt-hour data and USART communication mode is used to transfer data from ADWHM to PC. The accuracy of the voltage and unt measuring for ADWHM is verified by identifying the LCD display values of the ADWHM after the voltage signals of id levels from digital function generator is applied to PT(Potential Transformer) and CT(Current Transformer) output under state which it is separated from real power line. On the its basic functions such as watt-hour data recording function, voltage management data recording function and load management data recording function was verified by showing data for three days among the collected data to PC by RS232C communication from ADWHM which was connected to real power lines for a week.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.662-671
• /
• 2020

최근, 국·내외적으로 CO₂배출의 저감을 위한 기술적인 방안 중 하나로 도서지역의 마이크로그리드에 기 설치된 디젤발전기의 가동률을 줄이고 신재생에너지전원의 비중을 높여 운용하고 있는 실정이다. 특히, 국내에서는 가파도, 가사도, 울릉도 등의 도서지역에 디젤발전기와 신재생에너지, 전기저장장치로 구성된 독립형 마이크로그리드의 실증 및 보급 사업이 활발하게 진행되고 있으며, 기존의 디젤발전기 대신 정전압, 정주파수(constant voltage constant frequency, CVCF) 기능을 가진 CVCF 인버터 및 CVCF 인버터용 배터리를 도입하여 마이크로그리드를 안정적으로 운용하는 연구들이 진행되고 있다. 그러나, CVCF 인버터 기반 마이크로그리드의 정상상태 운용특성에 있어서, 출력이 불안정한 태양광전원과 풍력발전과 같은 신재생에너지전원이 계통에 연계되면서 전력품질에 많은 문제가 발생하고 있다. 따라서, 본 논문에서는 신재생에너지전원과 전기저장장치 연계에 따른 마이크로그리드의 운용특성을 분석하기 위하여, PSCAD/EMTDC를 이용하여 30kW급 마이크로그리드 시스템을 모델링하고, 이를 바탕으로 마이크로그리드 시험장치를 구현한다. 30kW급 마이크로그리드 시스템을 바탕으로 시뮬레이션 및 시험을 수행한 결과, 제안한 방법이 CVCF 인버터 기반의 마이크로그리드 시스템에서 저전압, 과전압 및 불평형 문제를 개선하는 데 유용함을 확인하였다.

• 전기전자학회논문지
• /
• 제25권4호
• /
• pp.721-727
• /
• 2021

본 논문은 게이티드 링 발진기를 이용한 UWB(Ultar-wideband) 임펄스 생성기 구조에 관한 내용이다. 기존 구조에서 필요로 하던 수 GHz의 발진기 및 PLL 회로를 게이티드 링 발진기로 대체하여 회로의 복잡도와 전력 낭비를 줄였다. 제안하는 방식은 링 발진기의 Head switch에 인가되는 Enable 신호의 길이를 조정함으로써 필요한 구간에만 발진기를 동작시키고 임펄스를 생성함으로써 출력 없이 쉬는 시간 동안 낭비되는 전력을 줄였다. 그리고 카운터를 통한 Pulse shaping 방법을 통해 사이드 로브의 발생을 억제하고 주파수 대역 변경을 위해 중심 주파수 변경시 대역폭 변화를 막을 수 있었다. 설계된 UWB 임펄스 생성기는 디지털 비트를 조정함으로써 6.0GHz에서 8.8GHz의 중심 주파수를 변경할 수 있으며 또한 사용 대역폭을 약 1.5GHz로 유지할 수 있음을 검증하였다.