• 한국생산제조학회지
• /
• 제24권6호
• /
• pp.647-652
• /
• 2015

A probe pin is a key component of LED inspection equipment. The probe pin makes contact with the LED electrodes and supplies an electric current. Because the mechanical and electrical homogeneity of the probe surface affects the service life and reliability, its characterization is essential. For this study, the hardness was measured using a micro-Vickers hardness test. Moreover, the thicknesses of the plating at different locations and the elemental compositions were examined using an FE-SEM. The uniformity of the plating was found to be acceptable because palladium was detected consistently throughout the tested domain. In addition, the hardness of the surface was determined to be higher than that of the typical palladium range, which is attributed to the use of undercoated nickel.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.1027-1028
• /
• 2010

• Tribology and Lubricants
• /
• 제23권6호
• /
• pp.255-260
• /
• 2007

This paper presents the contact pressure distribution of pin bushing bearings for various lubrication friction modes such as oil film and elastohydrodynamic lubrication contacts, a mixed lubrication contact, a boundary contact, and a dry contact. During a sliding contact of a plain bearing, the boundary and dry rubbing contacts are dominated between a piston pin and a pin bushing bearing. This may come from a micro-scale clearance, an explosive impact pressures from the piston head, and an oscillatory motion of a pin bearing. The computed results show that as the oil film parameter $h/{\sigma}$ is increased from the dry rubbing contact to the oil film lubrication friction, the maximum oil film pressure is radically increased due to an increased viscous friction with a thin oil film thickness and the maximum asperity contact pressure is reduced due to a decreased asperity contact of the rubbing surfaces.

• 제어로봇시스템학회논문지
• /
• 제19권11호
• /
• pp.979-983
• /
• 2013

The three-dimensional measurement method of confocal systems is a spot scanning method which has a high resolution and good illumination efficiency. However, conventional confocal systems had a weak point in that it has to perform XY axis scanning to achieve FOV (Field of View) vision through spot scanning. There are some methods to improve this problem involving the use of a galvano mirror [1], pin-hole array, etc. Therefore, in this paper we propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array in a dual microscope configuration. We made an area scan possible by using a combination MLA (Micro Lens Array) and pin-hole array, and used an objective lens to improve the light transmittance and signal-to-noise ratio. Additionally, we made it possible to change the objective lens so that it is possible to select a lens considering the reflection characteristic of the measuring object and proper magnification. We did an experiment using 5X, 2.3X objective lens, and did a calibration of height using a VLSI calibration target.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.543-548
• /
• 1994

This is the paper on the development of assemnly automation and visual inspection system for smart card reader connector. The automation consists of 3 main process injection, assembly and inspection. During the injection, the main pin of a reel. transferred under uniform tension, is cut with an injection interval and positioned precisely to an injection mold by roll feeder after injection. The main base is stacked to a magazine for main pin's exact positionning to a mold . For last effective production, The turn table and pick & place are driver with gears and came by a single monter. We developed the small parts handling technigue for stable supply of micro ist pin and 2nd pin and could determine the orientation and position of those pins. For reliable inspection, We used the vision system which examins the guality of arranged pins with a CCD camera. The connector models which can be manufactured with this system are 8 pin and 10 pin type. The user can select the connector model for production and adjust the torerable error range during the inspection of arranged pins.

• 소성∙가공
• /
• 제12권6호
• /
• pp.582-587
• /
• 2003

This paper is concerned with the mechanical property changes of the milli-size products manufactured by forward extrusion processes with square dies. Experiments are carried out with pure aluminum and pure copper billets. Extrusion ratio and knock-out pad are chosen as the important process parameters affecting the changes of mechanical properties such as shear strength and hardness. Shear strength tests with the extruded milli-size pin have shown the strong relation between victors hardness and shear strength in the neck of a stepped pin. As the extrusion ratio increases, the hardness on both the surface and the center line of a pin also increase. It is also noted that the hardness on the surface is a little higher than that on the center. The existence of knock-out pad in extrusion die causes the hardness in the neck of a extruded pin to increase. Finally, the approximated linear relations between shear strength and hardness of a pin are suggested.

• 한국식품과학회지
• /
• 제25권5호
• /
• pp.546-551
• /
• 1993

제분방법별(Pin mill, Colloid mill, Micro mill, Jet mill)로 제조한 쌀가루의 특성과 쌀 수제비 제조후 식미에 미치는 영향을 조사하였다. 지방, 회분, 단백질은 제분 방법에 따라 큰 차이를 보이지 않았다. 제분방법별 쌀 가루의 청값, 열수가용성 아밀로오스 함량, 그리고 전분 손상도는 Jet mill, Micro mill, Colloid mill, Pin mill의 순으로 높았음을 나타내었다. 수분흡수지수, 수분용해지수 및 보수력을 측정한 결과 전분손상도가 증가함에 따라 전체적으로 증가하였다. 또한 시료농도 15%의 겔을 형성하였을 때 Pin mill의 경우 강도에 있어서 가장 높음을 보여주었다. 아밀로그램을 이용한 호화개시온도와 최고점도는 입자가 미세하여 짐에 따라 점차 낮아지는 경향을 보였으며 Differential Scanning Colorimetry 측정에 의한 측정값도 아밀로그램에서와 동일한 양상을 나타내어 호화흡열의 면적에서 산출한 호화엔탈피$({\Delta}H)$가 Jet mill의 경우 0.83 kcal로 가장 낮았다. 즉 전분의 손상도가 증가함에 따라 호화엔탈피는 감소하였다. 쌀수제비 제조실험 결과는 Jet mill이 관능검사 결과 가장 우수한 것으로 판명되었고 반죽상태도 양호함을 보여주었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.797-801
• /
• 2003

The mechanical properties such as shear strength and the hardness of milli-size products that manufactured for various process parameters by forward extrusion using square dies are investigated. Shear strength test is implemented for the observation of relation between vickers hardness and shear strength in the interface of head and shaft part of a stepped pin. When the extrusion ratios of pure aluminum and pure copper billets increase, the hardness on both the surface and the center line of a pin also increase, especially the hardness on the surface is shown to be a little higher than on the center. The existence of knock-out pad in extrusion die caused hardness increase in the interface of a extruded pin. As compared shear strength with hardness of a pin, the approximated linear relations are suggested in this study.

• 한국산학기술학회논문지
• /
• 제18권4호
• /
• pp.50-57
• /
• 2017

본 사출 금형을 통해 제품 생산 시 사출 금형 내에서 제품 형상을 형성하는 코어는 금형 내부에 틀의 형태로 가공되어 설치되며 이때 부분적인 코어의 형상을 핀에 가공하여 설치하는 부품을 코어 핀이라 한다. 이러한 사출 코어 용 코어 핀은 제품의 소형화 집적화에 따라 그 크기가 마이크로의 크기로 작아지고 있다. 하지만 이를 가공 시 기존의 센터리스 연삭 장치로는 마이크로 사이즈의 피삭재를 고정하여 밀착 시켜주는 장치의 부재로 인해 진동이 발생한다. 이러한 이유로 마이크로 크기의 직경을 가지는 코어 핀의 경우 가공 시 진동에 의해 변형 발생으로 가공 불량률이 매우 높다. 따라서 본 논문에서는 마이크로 크기의 코어 핀을 가공하기 위해 기존의 평면 연삭기에 설치하여 사용이 가능한 소형의 연삭 시스템을 개발 하였다. 이를 이용하여 코어 핀에 대한 연삭 실험을 진행하였으며 표면 거칠기, 진원도, 원통도의 측정을 통해 성능을 검증하였다.

• 한국기계가공학회지
• /
• 제14권3호
• /
• pp.124-130
• /
• 2015

The purpose of this study is to investigate friction characteristics according to micro-dimple patterns. The surface texturing of micro-dimple patterns was tested to examine the friction of pin-on-disk using flat-on-flat contact geometry. The patterns of both dimple circle and groove pattern were adopted to carry out the effect of those ones. In the low loads, such as 13.8N and 27.7N, the friction coefficients of groove pattern were lower than those of dimple circle pattern. In many other comparisons of normal loads, the groove pattern had lower friction forces, which showed the effect of surface texturing. The relationship between sliding time and friction forces showed that the increase of friction forces of groove pattern were relatively lower than those of dimple pattern. In conclusion, the dimple patterns of dimple-circle pattern and groove pattern strongly contributed to reducing the friction between contacting materials.