• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.387-388
• /
• 2009

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.721-722
• /
• 2007

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2002년도 춘계공동학술발표회요약집
• /
• pp.288.2-288
• /
• 2002

• 한국주조공학회지
• /
• 제24권1호
• /
• pp.3-9
• /
• 2004

Die casting is "a process in which molten metal is injected at high velocity and pressure into a mold(die) cavity". Casting with smooth surfaces, high dimensional precision, complicated shapes, and reduced weight can be obtained using this process. But this process is susceptible to casting defects such as porosities, scattered chilled layers, hard spots, etc. For preventing casting defects, we developed "low-velocity high pressure die casting technology", "squeeze die casting technology", "heat insulating sleeve lubricant technology", and "direct pouring technology". The "direct pouring technology" is useful for producing molten metal without oxide contamination. It consists of a pumping system which supplies pure molten metal to the die casting machine. By using this technology, we have successfully reduced oxide contamination in castings to 1/20 of that of our previous castings.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.464-464
• /
• 2011

We report a method to fabricate a large-area metal nanowire-grid polarizer. Liquid-bridge-mediated nanotransfer molding (LB-nTM) is based on the direct transfer of metal nanowires from a mold to a transparent substrate via liquid layer. A metal particle solution is used as an ink in the LB-nTM, which can be used for the formation of metal nanowires. The nanowires have higher depth are preferred for high transmittance. The height of nanowires that we made is about 140 nm. Large-area WGP is fabricated with good average transmittance of 74.89% in our measuring range.

• 한국산학기술학회논문지
• /
• 제18권6호
• /
• pp.330-335
• /
• 2017

최근 자동차 산업에서 전기 모터 연료 전지에 대한 수요가 급증했으며, 연료 전지 케이스로 사용되는 사각형 알루미늄 캔에 대한 수요 또한 증가하고 있다. 직사각형 배터리 케이스의 바닥에 있는 에어 벤트는 비정상적으로 높은 압력이 발생할 때 미리 압력을 방출하여 큰 폭발을 방지하는 역할을 한다. 직사각형 컵 배터리 케이스는 6 단계의 다단계 딥 드로잉으로 외형을 만들고 직사각형 배터리 케이스와 용접하여 벤트 부품을 제작해왔다. 그러나 본 연구에서는 직사각형 케이스의 바닥면에 공기 벤트 형상을 직접 추가 하는 연구를 수행하였다. 단조의 초기 형상으로는 사각 컵 다단식 딥 드로잉 성형 해석에서 추출한 두께와 형상을 이용한 유한 요소 해석 기법을 사용 하였다. 그 결과, 예측 정밀도가 향상되고, 배부름 및 파단 등의 결함을 미리 예측할 수 있었다. 초기 분석 결과를 토대로 두 가지 단조 형상이 후보로 제시되었고 성형 해석을 통해 최적의 단조 형상을 결정 하였다. 이러한 결과를 바탕으로 금형을 제작하고 실제 결과와 분석 결과를 비교하여 본 연구의 타당성을 검증하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.319-324
• /
• 2001

A finite element model for the process of squeeze casting for metal matrix composites (MMCs) in cylindrical mold is developed. The fluid flow and the heat transfer are the fundamental phenomena in the squeeze casing process. To describe heat transfer with solidification of molten aluminum, the energy equation in terms of temperature and enthalpy are applied to two dimensional axisymmetric model which is similar to the experimental system. And one dimensional flow model is employed to simulate the transient metal flow. The direct iteration technique was used to solve the resulting nonlinear algebraic equations. A computer program is developed to calculate the enthalpy, temperature and fluid velocity. Cooling curves and temperature distribution during infiltration and solidification are calculated for pure aluminum. The temperature is measured and recorded experimentally. At two points of the perform inside and one point of the mold outside, thermocouple wire are installed. The time-temperature data are compared with the calculated cooling curves. The experimental results show that the finite element model can estimate the solidification time and predict the cooling process.

• Design & Manufacturing
• /
• 제6권1호
• /
• pp.63-66
• /
• 2012

In the manufacturing of a LCD TV bottom chassis, the distortion after forming should be suppressed below pre-defined amount to avoid contact with electric components. Finite element analysis procedure of forming and springback of a LCD TV bottom chassis is developed to investigate the distortion behaviour. It is shown that after the first forming large distortion occur due to uneven metal flow induced by various embossings. In the second forming, distortion is decreased by introducing bead that absorbs the excessive metal flow. It is proved that analysis method could describe these behaviour effectively. The developed analysis method can be used to find the proper location and shape of bead more quickly and effectively.

• 한국주조공학회지
• /
• 제27권2호
• /
• pp.88-94
• /
• 2007

General criteria for the risering design of steel castings and commercial codes for the flow and solidification analysis were used to design the optimized risering in V-process. Three type of specimens were chosen including thin plates and a thick disc. Sided riser installed in the front of a plate casting was effective to prevent the shrinkage defects and to increase the casting yield ratio. Exothennic sleeve and chill were also effective. It was possible to apply the general criteria for the risering design of steel castings to V-process. Temperature of a mold surface was expected to rise over $1,000^{\circ}C$ in the temperature calculation considering radiation effect of molten metal in the mold. Since weakening temperature of the vinyl used in V-process is about $70^{\circ}C$, it should be emphasized that a proper coating of the vinyl film is necessary to prevent the possibility of burning out of the vinyl by the molten metal.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.351-359
• /
• 2006

Ni based($Ni_{57}Zr_{20}Ti_{18}Si_2Sn_3$) bulk metallic glass(BMG) powders were produced by a gas atomization process, and ductile Cu powders were mixed using a spray drying process. The Ni-based amorphous powder and Cu mixed Ni composite powders were compacted by a spark plasma sintering (SPS) processes into cylindrical shape. The relative density varied with the used SPS mold materials such as graphite, hardened steel and WC-Co hard metal. The relative density increased from 87% to 98% when the sintering temperature increased up to $460^{\circ}C$ in the WC-Co hard metal mold.