• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.146-146
• /
• 2011

The blue light emitting diode (LED) structure based on non-polar a-plane (11-20) GaN which was coated TiO2 nanoparticles using spin coating method was grown on r-plane (1-102) sapphire substrates to improve light extraction efficiency. We report on the emission and structural properties with temperature dependence of photoluminescence (PL) and x-ray rocking curves (XRC). From PL results at 13 K of undoped GaN samples, basal plane stacking fault (BSF) and near band edge (NBE) emission peak were observed at 3.434 eV and 3.484 eV, respectively. We also found the temperature-induced band-gap shrinkage, which was fitted well with empirical Varshini's equation. The PL intensity of TiO2 nanoparticles ?coated multiple quantum well (MQW) sample is decayed slower than that of no coating sample with increasing temperature. The anisotrophic strain and azimuth angle dependence in the films were shown from XRC results. The full width at half maximum (FWHM) along the GaN [11-20] and [1-100] directions were 564.9 arcsec and 490.8 arcsec, respectively. A small deviation of FWHM values at in-plane direction is attributed to uniform in-plane strain.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.199-199
• /
• 2011

Recently, Thin film transistors (TFTs) with amorphous oxide semiconductors (AOSs) can offer an important aspect for next generation displays with high mobility. Several oxide semiconductor such as ZnO, $SnO_2$ and InGaZnO have been extensively researched. Especially, as a well-known binary metal oxide, tin oxide ($SnO_2$), usually acts as n-type semiconductor with a wide band gap of 3.6eV. Over the past several decades intensive research activities have been conducted on $SnO_2$ in the bulk, thin film and nanostructure forms due to its interesting electrical properties making it a promising material for applications in solar cells, flat panel displays, and light emitting devices. But, its application to the active channel of TFTs have been limited due to the difficulties in controlling the electron density and n-type of operation with depletion mode. In this study, we fabricated staggered bottom-gate structure $SnO_2$-TFTs and patterned channel layer used a shadow mask. Then we compare to the performance intrinsic $SnO_2$-TFTs and doping hafnium $SnO_2$-TFTs. As a result, we suggest that can be control the defect formation of $SnO_2$-TFTs by doping hafnium. The hafnium element into the $SnO_2$ thin-films maybe acts to control the carrier concentration by suppressing carrier generation via oxygen vacancy formation. Furthermore, it can be also control the mobility. And bias stability of $SnO_2$-TFTs is improvement using doping hafnium. Enhancement of device stability was attributed to the reduced defect in channel layer or interface. In order to verify this effect, we employed to measure activation energy that can be explained by the thermal activation process of the subthreshold drain current.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.354-354
• /
• 2012

In this study, we report the vertically aligned ZnO nanowires by using different type of Ga-doped ZnO (GZO) thin films as seed layers to investigate how the underlying GZO film micro structure affects the distribution of ZnO nanowires. Arrays of highly ordered ZnO nanowires have been synthesized on GZO thin film seed layer prepared on p-Si substrates ($7-13{\Omega}cm$) with utilize of a pulsed laser deposition (PLD). With the vapor-liquid-solid (VLS) growth process, the ZnO nanowire synthesis carries out no metal catalyst and is cost-effective; furthermore, The GZO seed layer facilitates the uniform growth of well-aligned ZnO nanowires. The influence of the growth temperature and various thickness of GZO seed layer have been analyzed. Crystallinity of grown seed layer was studied by X-Ray diffraction (XRD); diameter and morphology of ZnO nanowires on seed layer were investigated by field emission scanning electron microscopy (FE-SEM). Our results suggest that the GZO seed layer with high c-axis orientation, good crystallinity, and less lattice mismatch is key parameters to optimize the growth of well-aligned ZnO nanowire arrays.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.75-75
• /
• 2011

전이금속(transition metal) 질화물(nitride)은 높은 경도, 내마모성, 부식 저항성 그리고 내열성 등과 같은 우수한 기계적 물성 때문에 많은 연구가 되어 왔다. 이 중 질화 티타늄은 높은 경도, 내식 및 내마모의 우수한 기계적 특성으로 공구(tool)와 같은 제품의 수명 향상을 위한 표면 코팅으로 사용되어 왔으며, 금(gold)색의 미려한 색상을 이용한 제품의 외관 표면처리, 정형외과 및 치과용 보형물의 수명 및 안정성 향상 등 다양한 분야에 응용 되고 있다. 본 연구에서는 Cathodic Arc 코팅 방식을 이용하여 질화 티타늄을 합성하였으며, 경사 코팅에 따른 단층 및 다층 피막(3-layer)의 미세조직 변화와 그 물성을 평가하였다. 아크 소스에 장착된 타겟은 99.5%의 Ti 타겟을 사용하였고, 시편과 타겟 간의 거리는 약 31 cm이며, 시편은 알코올과 아세톤으로 초음파 세척 된 냉연강판과 SUS 304를 사용하였다. 시편을 진공용기에 장착하고 ~10-6 Torr까지 진공배기를 실시하고, Ar 가스를 진공용기 내로 공급하여 ~10-4 Torr에서 시편에 bias (Pulse : 400V)를 인가한 후 아크를 발생시켜 약 5분간 청정을 실시하였다. 플라즈마 청정이 끝나면 시편에 인가된 bias를 차단하고 코팅하였다. 경사 코팅을 위한 시편의 회전각은 $30^{\circ}$, $45^{\circ}$, $60^{\circ}$이며, 질화 티타늄의 두께는 약 $3{\mu}m$로 동일하게 코팅 하였다. 경사 코팅된 박막의 경우는 동일 시간 코팅하였을 경우 경사각이 커질수록 두께가 감소하였다. 경사각에 따라 코팅 층이 성장하였고, Bias를 인가 할 경우에는 경사 입사의 효과가 상쇄됨이 관찰되었다. 또한 경사 코팅에 의해 제조된 티타늄 질화물의 경도는 저하 되었으며, $30^{\circ}$와 $60^{\circ}$에 비해 $45^{\circ}$ 경우 경도 저하가 가장 적었다. 결론적으로 Cathodic 아크 코팅 방법으로 질화티타늄을 합성하였고, 경사 코팅을 통해 박막의 미세조직 변화를 확인 하였다. 본 연구에서 얻어진 결과를 이용하여 다양한 구조로 박막의 성장을 유도 할 수 있으며, 이를 통해 경도, 내마모성, 내식성 등의 물성을 변화시킬 수 있는 장점을 가질 것으로 예상된다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.158-158
• /
• 2012

A new kind of organic-inorganic hybrid polymer, poly(tetraphenyl)silole siloxane (PSS), was invented and synthesized for realization of its unique charge trap properties. The organic portions consisting of (tetraphenyl)silole rings are responsible for electron trapping owing to their low-lying LUMO, while the Si-O-Si inorganic linkages of high HOMO-LUMO gap provide the intrachain energy barrier for controlling electron transport. Such an alternation of the organic and inorganic moieties in a polymer may give an interesting quantum well electronic structure in a molecule. The PSS thin film was fabricated by spin-coating of the PSS solution in THF organic solvent onto Si-wafer substrates and curing. The electron trapping of the PSS thin films was confirmed by the capacitance-voltage (C-V) measurements performed within the metal-insulator-semiconductor (MIS) device structure. And the quantum well electronic structure of the PSS thin film, which was thought to be the origin of the electron trapping, was investigated by a combination of theoretical and experimental methods: density functional theory (DFT) calculations in Gaussian03 package and spectroscopic techniques such as near edge X-ray absorption fine structure spectroscopy (NEXAFS) and photoemission spectroscopy (PES). The electron trapping properties of the PSS thin film of quantum well structure are closely related to intra- and inter-polymer chain electron transports. Among them, the intra-chain electron transport was theoretically studied using the Atomistix Toolkit (ATK) software based on the non-equilibrium Green's function (NEGF) method in conjunction with the DFT.

• 센서학회지
• /
• 제15권1호
• /
• pp.58-64
• /
• 2006

In this study, we describe a low-temperature wafer-level thermocompression bonding using electroplated gold seal line and bonding pads by electroplating method for RF-MEMS devices. Silicon wafers, electroplated with gold (Au), were completely bonded at $320^{\circ}C$ for 30 min at a pressure of 2.5 MPa. The through-hole interconnection between the packaged devices and external terminal did not need metal filling process and was made by gold films deposited on the sidewall of the throughhole. This process was low-cost and short in duration. Helium leak rate, which is measured to evaluate the reliability of bonded wafers, was $2.7{\pm}0.614{\times}10^{-10}Pam^{3}/s$. The insertion loss of the CPW packaged was $-0.069{\sim}-0.085\;dB$. The difference of the insertion loss between the unpackaged and packaged CPW was less than -0.03. These values show very good RF characteristics of the packaging. Therefore, gold thermocompression bonding can be applied to high quality hermetic wafer level packaging of RF-MEMS devices.

• 공업화학
• /
• 제10권2호
• /
• pp.225-230
• /
• 1999

Li(DPM)을 원료로 hot wall 수평 관형 반응기를 이용하여 질소-산소 및 아르곤-산소의 분위기에서 $Li_2O$ 고체박막을 LPMOCVD법으로 합성하였다. XRD와 ESCA 분석으로부터 질소-산소 분위기에서는 $Li_2CO_3$막이, 아르곤-산소의 분위기에서는 $Li_2O$막이 성장하였음을 알아냈다. 성막된 산화리튬과 리튬카보네이트는 기판의 실리콘 성분과 반응하여 실리케이트를 형성하였다. 마이크로 trench법과 Monte Carlo 시뮬레이션에 의해 기상반응 속도상수 및 표면반응 속도상수가 얻어졌으며 이를 이용한 성막속도 계산치와 실험치를 비교한 결과 실험조건범위 내에서 잘 일치하였다.

• 정보저장시스템학회논문집
• /
• 제1권2호
• /
• pp.127-131
• /
• 2005

We report a nanometer scale mark formation using a $PtO_x$ thin film or a TbFeCo rare-earth transition metal film and the mechanism. The multi-layer samples($ZnS-SiO_2/PtOx/ZNS-SiO_2,\;ZnS-SiO_2/TbFeCo/ZnS-SiO_2$) were prepared with a magnetron sputtering method on a polycarbonate or a glass substrate. By laser irradiation of approximately a few nanoseconds, nanometer scale marks were fabricated. During the fabrication process, the thin films were thermally reacted or inter-diffused during the laser irradiation. 75 nm bubble marks in the PtOx multi-layer sample by an approximately 4-ns laser irradiation. Inside the bubble mark, Pt particles with a few nanometer sizes are distributed. The $50{\sim}100$ nm bubble marks in the TbFeCo multi-layer sample by a few nanosecond laser irradiations. We will report the detail structure of the samples, the bubble mark formation process and the mechanism.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.82-82
• /
• 2018

광전소자용 투명전극으로 적용하기 위한 초박형 Al 박막에 대해서 기초연구를 수행하였다. 증착 전 챔버(chamber) 내 기저압력은 $3{\times}10^{-7}Torr$이하로 유지하였으며 Ar 불활성 기체의 유입을 통해 작업압력을 $1{\times}10^{-2}Torr$로 상승시켜 증착을 실시하였다. DC 마그네트론 스퍼터링법을 이용하여 유리기판상에 Al 박막의 증착을 실시하였으며, 박막의 두께가 3-12 nm인 Al 박막을 각각 형성하였다. 두께가 7 nm 일 때 면저항은 $135{\Omega}/{\square}$로 측정되었고 7 nm 이상인 두께의 박막은 두께가 증가할 때 면저항이 점진적으로 감소되는 경향을 확인할 수 있었다. 두께가 10 nm인 박막의 측정된 면저항은 $13.1{\Omega}/{\square}$로 두께 7 nm인 박막과 비교하였을 때 약 10배의 차이를 확인할 수 있었다. 두께 6 nm 이하인 박막은 면저항 측정이 불가능하였는데 이는 SEM 분석 결과, 연속박막을 이루지 못 하였기 때문이라고 결론을 내릴 수 있었으며, 두께 12 nm인 박막까지 완전한 연속박막이 형성되지 않았다. 각각의 박막에서 입자의 크기는 선 교차법(line intercept method)을 이용하여 시편당 평균 120개의 입자에 대한 평균값을 측정하였으며, 이론적으로 예상할 수 있는 바와 같이 두께가 증가할수록 입자크기도 비례하여 증가하게 되는 것을 확인할 수 있었다. 가시광선 파장영역 내 투과도의 경우, 3 nm 두께에서 평균 80% 이상의 투과도가 측정된 데 반하여, 4-5 nm 두께에서 평균 60%로 급격하게 감소되기 시작하며 그 이후, 두께 증가에 따라 투과도가 점진적으로 감소되는 경향을 확인할 수 있었다. 또한 Al 박막은 시간의 경과에 따른 표면의 산화가 진행되어 기존에 측정된 면저항보다 10-60%의 면저항이 증가하였는데 이는 두께가 얇을수록 더 산화의 영향을 많이 받기 때문에 나타난 결과로 보인다. 추후 산화방지막 및 빛반사방지막 층을 초박형 Al박막과 함께 Oxide/Metal/Oxide 구조로 형성하여 위와 같은 현상들을 해결하고 박막물성의 증진을 통해 투명전극에 적용을 목표로 한다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.67-67
• /
• 2018

The 5xxx series aluminum alloys are recently used in not only marine system but also automotive area because of a low density material, good mechanical properties and better resistance to corrosion. However, Aluminum alloys are less resistant than the purest aluminum such as 1xxx aluminum alloy. Electrochemical anodization technique has attracted in the area of surface treatment because of a simple procedure, a low-cost efficiency than other techniques such as lithography and a large volume of productivity, and so on. Here, The relationship between the corrosion behavior and the thickness of aluminum anodic oxide have been studied. Prior to anodization, The 5052 aluminum sheets ($30{\times}20{\times}1mm$) were degreased by ultra-sonication in acetone and ethanol for 10 minutes and eletropolished in a mixture of perchloric acid and ethanol (1:4, volume ratio) under an applied potential of 20V for 60 seconds to obtain a regular surface. During anodization process, Aluminum alloy was used as a working electrode and a platinum was used as a counter electrode. The two electrodes were separated at a distance of 5cm. The applied voltage of anodization is conducted at 40V in a 0.3M oxalic acid solution at $0^{\circ}C$ with appropriate magnetic stirring. The surface morphology and the thickness of AAO films was observed with a Scanning Electron Microscopy (SEM). The corrosion behavior of all samples was evaluated by an open-circuit potential and potentio-dynamic polarization test in 3.5wt% NaCl solution. Thus, The corrosion resistance of 5052 aluminum alloy is improved by the formation of an anodized oxide film as function of increase anodization time which artificially develops on the metal surface. The detailed electrochemical behavior of aluminum 5052 alloy will be discussed in view of the surface structures modified by anodization conditions such as applied voltages, concentration of electrolyte, and temperature of electrolyte.