• Journal of Environmental Science International
• /
• v.21 no.7
• /
• pp.787-795
• /
• 2012

The purpose of this study is to synthesize transition metal doped mesoporous silica catalyst and to characterize its surface in an attempt to decomposition of $N_2O$. Transition metal used to surface modification were Ru, Pd, Cu and Fe concentration was adjusted to 0.05 M. The prepared mesoporous silica catalysts were characterized by X-ray diffraction, BET surface area, BJH pore size, Scanning Electron Microscopy and X-ray fluorescence. The results of XRD for mesoporous silica catalysts showed typical the hexagonal pore system. BET results showed the mesoporous silica catalysts to have a surface area of 537~973 $m^2/g$ and pore size of 2~4 nm. The well-dispersed particle of mesoporous silica catalysts were observed by SEM, the presence and quantity of transition metal loading to mesoporous surface were detected by XRF. The $N_2O$ decomposition efficiency on mesoporous silica catalysts were as follow: Ru>Pd>Cu>Fe. The results suggest that transition metal doped mesoporous silica is effective catalyst for decomposition of $N_2O$.

• Journal of Environmental Science International
• /
• v.22 no.7
• /
• pp.837-845
• /
• 2013

This study was designed to synthesize mesoporous carbon, porous carbonic material and to characterize its surface in an attempt to adsorption methane gas($CH_4$). Synthesis of mesoporous carbon was carried out under two steps ; 1. forming a RF-silica complex with a mold using CTMABr, a surfactant, and TEOS, raw material of silica, and 2. eliminating silica through carbonization and HF treatment. The mesoporous carbon was synthesized under various conditions of synthesis time and calcination. Eight different types of mesoporous carbon, which were designated as MC1, MC2, MC3, MC4, MCT1, MCT2, MCT3, and MCT4, were prepared depending upon preparation conditions. The analysis of mesoporous carbon characteristics showed that the calcination of silica stabilized the mixed structure of silica and carbonic complex, and made the particle uniform. The results also showed that hydrothermal synthesis time did not have a strong influence on the size of pore. The bigger specific surface area was obtained as the hydrothermal synthesis time was extended. However, the specific surface area was getting smaller again after a certain period of time. In adsorption experiments, $CH_4$ was used as adsorbate. For the case of $CH_4$, MCT3 showed the highest adsorption efficiency.

• Journal of Environmental Science International
• /
• v.19 no.6
• /
• pp.681-687
• /
• 2010

Mesoporous silica was prepared from hydrothermal synthesis using gel mixture of tetraethylorthosilcate (TEOS) as silica source and cetyltrimethylammonium bromide (CTMABr) as a surfactant. In the optimum synthesis cause, molar ratio of template and silica changed. The surface and structure properties of mesoporous silica were determined by XRD, SEM, TEM and BET. Also, surface potential of mesoporous silica was measured using zeta potential. $N_2$ adsorption isotherm characteristics, including the specific surface area ($S_{BET}$), total pore volume $V_T$), and average pore diameter ($D_{BJH}$), were determined by BET. As a result, SBET of $100m^2/g{\sim}1500m^2/g$ was determined from the $N_2$ adsorption isotherm. Also, the average pore diameter was 2 nm∼4 nm. Mesoporous silica's surface potential of minus charge was determined from zeta potential.

• Journal of the Korean Ceramic Society
• /
• v.44 no.7
• /
• pp.358-361
• /
• 2007

Well-ordered mesoporous SiCBN ceramics have been successfully synthesized by infiltrating a polymeric precursor, which was prepared from borazine and 2,4,6-trimethyl-2,4,6-trivinylcyclotrisilazane via a hydroboration reaction, into a mesoporous carbon (CMK-3) as a hard template. This was followed by pyrolysis at $1400^{\circ}C$ under nitrogen gas and subsequent oxidative removal of the carbon template without chemical etching. The prepared mesoporous SiCBN ceramic was characterized by a small-angle XRD, TEM, and BET surface area. The resulting mesoporous SiCBN ceramic revealed a BET surface area of $275 m^2g^{-1}$ and a pore volume of $0.8 cm^3 g$ with no crystallization.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.159.1-159.1
• /
• 2014

We report a simple method for preparing hydrophobic mesoporous silica and its use as a pre-concentrating agent of gas analytes. Hydrophobic mesoporous silica was prepared by coating PDMS (polydimethylsiloxane) thin layer on commercial mesoporous silica with thermal deposition method in a sealed chamber. By using this method, we were able to coat PDMS layer on inner-walls of pores larger than 15 nm. Also, contact angle measured on a surface consisting of PDMS-coated mesoporous silica exceeded $150^{\circ}$, implying that the surface has high water repellency. Pre-concentration ability of PDMS-coated mesoporous silica and baremesoporous silica was tested under dry and humid conditions. Adsorption and molecular desorption of gas analytes was much enhanced by PDMS-coating on mesoporous silica under both dry and humid conditions. Therefore we suggest that PDMS-coated mesoporous silica can be an efficient pre-concentration agent in order to enhance sensitivity of various detectors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.159-159
• /
• 2007

In order to reduce a signal delay in ULSI, low resistive metal and intermetal dielectric material of low dielectric constant are required. Ordered mesoporous silica film is proper to intermetal dielectric due to its low dielectric constant and superior mechanical properties. In this study, ordered mesoporous silica films was synthesized using TEOS (tetraethoxysilane) / MTES (methyltriethoxysilane) mixed silica precursor and Brij-$76^{(R)}$ surfactant. These films had the porosity of 40% and dielectric constant of 2.5. To lower dielectric constant, the ordered mesoporous silica films were surface-modified by HMDS (hexamethyldisilazane) treatment. HMDS substituted -OH groups on the surface of silica wall for -Si$(CH_3)_3$ groups. After the HMDS treatment, ordered mesoporous silica films were calcined at various calcination temperatures. Through the investigation, it was concluded that the proper calcination temperature is necessary as aspects of structural, electrical, and mechanical properties.

• Korean Journal of Materials Research
• /
• v.20 no.2
• /
• pp.97-103
• /
• 2010

In this study, a new, relatively simple fabrication method for forming a mesoporous $Al(OH)_3$ film on Al substrates was demonstrated. This method, i.e., alkali surface modification, was simply comprised of dipping the substrate in a $5\times10^{-3}$ M NaOH solution at $80^{\circ}C$ for one minute and then immersing it in boiling water for 30 minutes. After alkali surface modification, a mesoporous $Al(OH)_3$ film was formed on the Al substrate, and its chemical state and crystal structure were confirmed by XPS and TEM. According to the results of the XPS analysis, the flake-like morphology after the alkali surface modification was mainly composed of $Al(OH)_3$, with a small amount of $Al_2O_3$. The mesoporous $Al(OH)_3$ layer was composed of three regions: an amorphousrich region, a region of mixed amorphous and crystal domains, and a crystalline-rich region near the $Al(OH)_3$ layer surface. It was confirmed that the stabilization process in the alkali surface modification strongly influenced the crystallization of the mesoporous $Al(OH)_3$ layer.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.1
• /
• pp.16-22
• /
• 2007

Recently, mesoporous metallic materials are becoming more and more important in various applications like catalysts, electrochemical detectors, batteries, and fuel cells because of their high surface area. Among the various methods for manufacturing mesoporous structure, surfactant templating method followed by electroplating has been tried in this study. A mesoporous metallic film was prepared by electrodeposition from electroplating solution mixed with surfactant template. Nonionic type lyotropic liquid crystalline surfactant, Brij56, and nickel acetate based solution were selected as a template material and electroplating solution, respectively. To determine the content of surfactant forming a hexagonal column structure, the phase diagram of electroplating solution and surfactant mixture has been exploited by polarized optical microscopy equipped with heating and cooling stage. Nickel films were electroplated on Cu foil by stepwise potential input method to alleviate the concentration polarization occurred during the electroplating process. TEM and XRD analyses were performed to characterize the size and shape of mesostructures in manufactured nickel films, and electrochemical characterization was also carried out using cyclic voltammetry.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.2
• /
• pp.449-453
• /
• 2009

A mesoporous assembly of layered titanate with well-dispersed Pt cocatalysts has been synthesized via a restacking of exfoliated titanate nanosheets and a simultaneous adsorption of Pt nanoparticles. According to powder X-ray diffraction analysis, the obtained mesoporous assembly shows amorphous structure corresponding to the disordered stacking of layered titanate crystallites. Field emission-scanning electron microscopy and $N_2$ adsorption-desorption isotherm measurement clearly demonstrate the formation of mesoporous structure with expanded surface area due to the house-of-cards type stacking of the titanate crystallites. From high resolution-transmission electron microscopy and elemental mapping analyses, it is found that Pt nanoparticles with the size of ~2.5 nm are homogeneously dispersed in the mesoporous assembly of layered titanate. In comparison with the protonated titanate, the present mesoporous assembly of layered titanate exhibits better photocatalytic activity for the photodegradation of organic molecules. This finding underscores that the restacking of exfoliated nanosheets is quite useful not only in creating mesoporous structure but also in improving the photocatalytic activity of titanium oxide.

• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.298-300
• /
• 2007

Frictional characteristics of mesoporous $SiO_2$ thin films were evaluated with different pore sizes. The films were manufactured by sol-gel and self-assembly methods to have a porous structure. The pores on the surface may play as the outlet of wear particle and the storage of lubricant so that the surface interactions could be improved. The pores were exposed on the surface by chemical mechanical polishing (CMP) or plasma-etching after forming the porous films. The ball-on-disk tests with mesoporous $SiO_2$ thin films on glass specimen were conducted at sliding speed of 15 rpm and a load of 0.26 N. The results show considerable dependency of friction on pore size of mesoporous $SiO_2$ thin films. The friction coefficient decreased as increasing the pore size. CMP process was very useful to expose the pores on the surface.