• International Journal of Air-Conditioning and Refrigeration
• /
• 제14권4호
• /
• pp.125-130
• /
• 2006

This study has been performed to investigate the thermal performance of variable conductance heat pipe (VCHP) with screen meshed wick. The active length of condenser section in a VCHP is varied by non-condensible gas, which controls the operating temperature, and the heat capacity of VCHP is controlled by the operating temperature. In this study, numerical analysis of the VCHP based on the diffusion model of non-condensible gas is done for the thermal control performance of VCHP. Water is used as a working fluid and nitrogen as a control non-condensible gas in the copper tube. As a result, the thermal conductance of VCHP has been compared with that of constant conductance heat pipe (CCHP) corresponding to the variation of operating temperature.

• ETRI Journal
• /
• 제40권5호
• /
• pp.582-591
• /
• 2018

In this paper, we present a performance analysis of large-scale multi-input multi-output (MIMO) systems for wireless backhaul networks. We focus on fully connected N nodes in a wireless meshed and multi-hop network topology. We also consider a large number of antennas at both the receiver and transmitter. We investigate the transmission schemes to support fully connected N nodes for half-duplex and full-duplex transmission, analyze the achievable ergodic sum rate among N nodes, and propose a closed-form expression of the achievable ergodic sum rate for each scheme. Furthermore, we present numerical evaluation results and compare the resuts with closed-form expressions.

• Composites Research
• /
• 제28권4호
• /
• pp.244-248
• /
• 2015

When a small gear rotates at a very high speed over 40,000 rpm, frictional heat is generated on the gear surfaces. Thermal deformations and stresses arising from frictional heat may lower the efficiency and fatigue life of the high-speed gear. Especially, such frictional heat has much stronger effects on the performance of millimeter-sized high-speed gears used for surgical and dental hand-pieces, due to a small surface area. An analytical equation was derived to calculate frictional temperature on a mating gear surface and conduction heat transfer analysis was performed. Thermal deformation and contact stresses were then calculated using FEM for gears used for medical hand-pieces. The contact stresses of the meshed gear and pinion increase by 19.4% and 16.4%, respectively, when the frictional thermal deformations are considered.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권3호
• /
• pp.118-126
• /
• 2002

AVR parameter tuning for voltage control of generators has generally been done with the off-line open-circuit model of the synchronous generator. When the generator is connected on-line and operating with load the AVR operates in an entirely different environment from the open-circuit conditions. This paper describes a new method for AVR parameter tuning for on line conditions using SQP(Sequential Quadratic Programming) meshed with frequency response characteristics of linearized on-line system model. As the proposed method uses the un - line system model the tuned parameter sets show more optimal behavior in the on-line operating conditions. furthermore, as this method considers the performance indices that are needed for stable operation as constraints, AVR parameter sets that are tuned by this method could guarantee the stable performance, too.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.135-136
• /
• 2006

In this paper, isolation strategies for improving broadband circuit performance and preventing noise arising from circuit component coupling are presented. Equivalent circuit parameters, including parasitic elements, are determined for capacitor and inductor structures. The effects of the relative position of the components with regard to a ground plane are considered in the equivalent circuits. Novel meshed ground structures are investigated to determine a configuration that improves the overall circuit performance.

• International Journal of CAD/CAM
• /
• 제11권1호
• /
• pp.11-17
• /
• 2011

A new method has been developed in this paper for automatic quadrilateral mesh generation for a two-dimensional domain. The method is named 'centering method' because it centers a point at the domain and then divides it into sub-domains using cutting lines from the center point. Each of the cutting lines is selected based on the criterion using the angles between the boundary of the domain and the cutting line. The decomposition of the domain into sub-domains is repeated until every subdomain has four or six nodes. Pre-defined splitters are used to divide six-node domains into quadrilateral elements depending on their configuration and presence on the boundary of the initial domain. Arbitrary domains are meshed as examples to verify the robustness of the new method.

• 한국통신학회논문지
• /
• 제32권6A호
• /
• pp.511-518
• /
• 2007

현재의 전송네트워크용량을 향상시킬때 중요하게 고려해야 할것중의 하나가 네트워크 scalability 이다. 새로운 풀 메쉬의 링 확장 방법 및 플래닝 툴을 제안하였다. 3$\sim$15 노드의 확장링에서 본 툴을 사용하여 SNR이 증진되는 것을 입증하였다. 노드의 출력신호 및 광 SNR이 제안된 NPOT에 의해 -16dBm/10dB 에서 +005dBm/21dB 로 증진되었다.

• 센서학회지
• /
• 제14권5호
• /
• pp.343-349
• /
• 2005

Carbon nitride films were deposited on various substrates for humidity sensors with meshed electrode by reactive RF magnetron sputtering system. As the ratio of injected nitrogen was decreased, the sensitivity of sensor was increased. When the ratio of injected nitrogen was $50{\sim}70%$, the sample showed the best linearity. The sensor impedance changed from $95.4{\;}k{\Omega}$ to $2.1{\;}k{\Omega}$ in a relative humidity range of 5 % to 95 %. The humidity sensors based on silicon wafer revealed higher lineality and faster response than those of alumina or quartz substrates. The adsorption saturation time of the sample was about 80 sec, and its desorption time was about 90 sec.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.189-190
• /
• 2006

During cold compaction processes loose powder is pressed under tooling action in order to produce complex shaped engineering components. Here, the analysis of the plastic deformation of granular packings is of fundamental importance to the development of computer simulation models. Powders can be idealized by packing discrete particles, where each particle is a sphere meshed with finite elements. The pressing of a body centered cubic packing was compared with numerical prediction and experimental data. The global response was expressed in force-displacement curve, and the accuracy of the numerical models analyzed for high relative densities up to 0.95.

• 조명전기설비학회논문지
• /
• 제16권3호
• /
• pp.61-66
• /
• 2002

배전시스템은 고 신뢰도가 요구되는 사례시스템이다. 신뢰도는 정해진 기간과 운전 조건하에서 설비나 시스템이 적절히 자기 기능을 할 수 있는 확률로 정의된다 수용가에서 배전시스템의 성능을 예측하고 검증하기 위한 기본적인 신뢰지수는 평균고장률, 평균고장기간, 평균 활용률 등이 포함된다 본 논문에서는 EDSA의 배전계통 신뢰도 평가 프로그램을 이용하여 배전 시스템의 기본적인 신뢰도 평가지수를 구하고, 수지식 사례 배전시스템을 개선시키기 위한 방법으로 환상식 시스템으로 구성을 변경시켜 수치적으로 얼마나 높은 신뢰도가 얻어졌는지를 보여준다.