• TTA 저널
• /
• 통권87호
• /
• pp.157-161
• /
• 2003

한국정보통신기술협회(TTA)는 2003년 3월 7일 대은전자㈜(http://www.dek.co.kr/) Gate Hub(모델명: DEK1521)의 성능시험을 수행하여 TTA Verified 인증서(번호: TTA-V-N-03-014)를 발급하였다. 또한 2003년 4월 3일 ㈜네오정보시스템(http://www.neoinfosys.co.kr/) 세대통신 분배장치(모델명: NIS - HM1616A)의 성능시험을 수행하여 TTA Verified 인증서(번호: TTA-V-N-03-026)를 발급하였다. 위의 두 장비는 Fast Ethernet Switch module과 전화 및 데이터 라인 연결 module을 함께 갖추었으며, TTA가 위의 두 장비를 이용하여 수행한 시험은 Fast Ethernet Switch module의 성능을 측정하는 것이었다. 본 고에서는 TTA가 마련한 Fast Ethernet Switch에 대한 인증기준(TTA-V-N-03-004-CC20)을 바탕으로 위의 두 장비에 대해 수행한 Fully meshed Throughput/Aging 시험 결과를 소개한다.

• 대한기계학회논문집B
• /
• 제24권6호
• /
• pp.777-784
• /
• 2000

A Navier-Stokes code based on an unstructured finite volume method is used to simulate the MIT flapping foil experiment. A low Reynolds number ${\kappa}-{\varepsilon}$ turbulence model is used to close the Reynolds averaged Navier-Stokes equations. Computations are carried out for the whole experimental domain involving two flapping foils and a downstream hydrofoil. The computational domain is meshed with unstructured quadrilateral elements, partly structured. Numerical solutions show good agreement with experiment. The first harmonics of the velocity in the boundary layer shows local peak value inside the boundary layer and also local minimum near the edge of boundary layer. It is intensified as it develops along the blade surface. This is shown to be caused as the unsteadiness inside the boundary layer is being convected at a speed less than the free stream value. It is also shown that there is negligible mixing of the unsteadiness between the boundary layer and the free stream.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.7-12
• /
• 2003

heat pipe with screen meshed wick. The heat pipe was designed in 200 screen meshs, 500 mm length and 12mm O.D tube of copper, water as working fluid and nitrogen as non-condensible gas. Heat pipe used in this study has evaporator, condenser and adiabatic section, respectively. Experimental data of wall temperature distribution along axial length is presented for heat transport capacity, condensor cooling water temperature change, degrees of an inclination angle, and operating temperature.

• 한국정밀공학회지
• /
• 제20권2호
• /
• pp.192-198
• /
• 2003

A finite element analysis of end-to-end artery/PTFE anastomosis has been presented in this study to evaluate the distribution of compliance and stresses in the vicinity of the anastomosis due to any mismatch in compliance characteristics. The artery wall was assumed to be made of linear isotropic material in this simplified model and a nonlinear analysis and convergency study with respect to increasing meshed element numbers were performed with a mean artery pressure loading of the artery-PTFE model. Also, sub-modeling method was Introduced to progress the accuracy of the finite element analysis. The results are as follow : 1. A hypercompliant zone on the artery side was observed around 4.Omm from the anastomosis and a high hoop stresses in the wall of artery and PTFE was dominant. 2. An artery displays large deformation so that nonlinear analysis and sub-modeling method was used. 3. An anastomosis with the thinner thickness and larger diameter PTFE (B type) could reduce the compliance disagreement.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.784-787
• /
• 2002

The NURBS surfaces are widely employed for exchanging geometric models between different CAD/CAE systems. However if the input NURBS surfaces are poorly parameterized, most surface meshing algorithms may fail or the constructed meshes can be ill-conditioned. In this paper presents a new method is presented that can generate well conditioned meshes even on poorly parameterized NURBS surfaces by regenerating NURBS surfaces. To begin with, adequate Points are sample on original poorly parameterized surfaces and new surfaces are created by interpolating these points. And then. mesh generation is performed on new surfaces. With this method, models with poorly parameterized NURBS surfaces can be meshed successfully.

• 한국초전도ㆍ저온공학회논문지
• /
• 제7권2호
• /
• pp.16-20
• /
• 2005

As power systems grow more complex and power demands increase, the fault current tends to gradually increase. In the near future, the fault current will exceed a circuit breaker rating for some substations, which is an especially important issue in the Seoul metropolitan area because of its highly meshed configuration. Currently, the Korean power system is regulated by changing the 154kV system configuration from a loop connection to a radial system, by splitting the bus where load balance can be achieved, and by upgrading the circuit breaker rating. A development project applying 154kV Superconducting Fault Current Limiter (SFCL) to 154kV transmission systems is proceeding with implementation slated for after 2010. In this paper, SFCL is applied to reduce the fault current in power systems according to two different application schemes and their technical impacts are evaluated. The results indicate that both application schemes can regulate the fault current under the rating of circuit breaker, however, applying SFCL to the bus-tie location is much more appropriate from an economic view point.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.65-67
• /
• 2001

Because of the difficulty of acquiring new generation sites and right- of-way, additional units have been added to the existing generation sites and the transmission system has been developed into highly meshed configuration. The reliable operation of power systems has been restricted by this system characteristics. The enhancement of system analysis techniques and establishment of appropriate measures have been required in this situation. In addition the deregulation of electric power industry in Korea would give rise to better tools for power system analysis and control. In this paper, dynamic models were developed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 A
• /
• pp.68-70
• /
• 2001

Because of the difficulty of acquiring new generation sites and right- of-way, additional units have been added to the existing generation sites and the transmission system has been developed into highly meshed configuration. The reliable operation of power systems has been restricted by this system characteristics. The enhancement of system analysis techniques and establishment of appropriate measures have been required in this situation. In addition the deregulation of electric power industry in Korea would give rise to better tools fur power system analysis and control. In this paper, dynamic models were developed and stability studies were implemented using developed dynamic models of EUROSTAG and compared with the simulation results of PSS/E.

• International Journal of CAD/CAM
• /
• 제9권1호
• /
• pp.17-24
• /
• 2010

For several years, researchers have focused on improving the integration of the CAD, CAM and Analysis through a better communication between the various analysis tools. This tendency to integrate the CAD/Analysis and automation of the corresponding processes requires data sharing between the various tasks using an integrated product model. We are interested in this research orientation to CAD/CAM/Analysis integration by rebuilding the CAD model (BREP), starting from the Analysis results (deformed mesh). Because this problem is complex, it requires to be split into several complementary parts. This paper presents an original interoperability process between the CAD and CAE. This approach is based on a new technique of rebuilding the CAD surface model (Nurbs, Bezier, etc.) starting from triangulation (meshed surface) as a main step of the BREP solid model. In our work, the advantages of this approach are identified using a centrifugal pump example.

• 한국정보과학회:학술대회논문집
• /
• 한국정보과학회 2004년도 봄 학술발표논문집 Vol.31 No.1 (A)
• /
• pp.430-432
• /
• 2004

Multicasting is an efficient means of one to many (or many to many) communications. Due to the frequent and unpredictable topology changes, multicast still remains as challenge and no one-size-fits-all protocol could serve all kinds of needs in ad hoc network. Protocols and approaches currently proposed on this issue could be classified mainly into four categories, tree-based, meshed-based, statelessness and hybrid. In this article, we borrow the concept of Eulerian ring in graph theory and propose a novel ring-based multicast framework--Hierarchical Eulerian Ring-Oriented Multicast Architecture (HEROMA) over wireless mobile Ad hoc network. It is familiar with hybrid protocol based on mesh and tree who concentrates on efficiency and robustness simultaneously. Architecture and recovery algorithm of HEROMA are investigated in details. Simulation result is also presented, which show different level of improvements on end-to-end delay in scenario of small scale.