• 한국방재학회 논문집
• /
• 제10권3호
• /
• pp.45-52
• /
• 2010

기후변화와 교통의 관계는 크게 기후변화가 교통에 미치는 영향과 교통이 기후변화에 미치는 영향으로 나눌 수 있다. 본 연구에서는 전자의 관점에서 폭설이 도시교통에 미치는 영향을 파악하였으며, 통행자의 불편익에 대한 방안을 제시함으로 폭설에 대해 효과적으로 대처하고자 하였다. 예기치 못한 기후변화의 파급효과는 통행시간과 운행비용, 사고비용 등으로 분석되었으며, 이를 기반으로 해당구간의 융설시스템(Snow Melting System) 도입에 따른 사업의 효과성을 분석하였다. 본 연구의 결과는 기후변화로 인한 교통불편익을 최소화하는 방재시설물 설치를 위한 평가기준으로 적용될 수 있을 것이다.

• 한국수산과학회지
• /
• 제47권3호
• /
• pp.241-246
• /
• 2014

Viruses in the genus Megalocytivirus have been subdivided into four subgroups. Among these subgroups 2 and 4, represented by the red sea bream iridovirus (RBIV) and the olive flounder iridovirus (FLIV), respectively, are non-exotic. subgroups 1 and 3, represented by the red sea bream iridovirus (RSIV) and the infectious spleen and kidney necrosis virus (ISKNV), respectively, have not been detected in Korea and are known as exotic. Shellfish are filter-feeders, and can thus filter and accumulate Megalocytivirus in their digestive glands, allowing us to track viral contamination in surrounding aquatic environment. In this study, we developed a high-resolution melting (HRM) analysis to differentiate among subgroups of Megalocytivirus accumulated in shellfish, and confirmed the convenience and efficiency of this method. More than two subgroups of Megalocytivirus were found in the digestive gland of a single shellfish. We classified all Megalocytivirus viruses from shellfish in Korea into subgroups 2 and 4, although proportions of subgroups were different among regions. Compared to nucleotide sequencing analysis, HRM analysis is a simple and rapid method for differentiating of Megalocytivirus subgroups.

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.54-61
• /
• 2015

In this study, effect of laser power on hardness and microstructure of SKD61 Hot Die steel of which surface was melted and hardened with Yb:YAG disk laser was investigated. Beam speed was fixed at 70 mm/sec and distance between them was 0.8 mm about Laser surface melting. The only thing that was changed laser power. Laser powers were 2.0, 2.4 and 2.8 kW. No defect was found under all conditions. As the laser power increased, the penetration depth were deepened and the bead width was also widened. There was no hardness deviation of fusion zone at same laser power and it was higher than that of heat affected zone. In addition, the more laser power increased, the more hardness in fusion zone decreased. Fusion zone was macroscopically dendrite structure. However, core matric in dendrite was lath martensite of 100 nm size. There were $M_{23}C_6$ of 500 nm and the VC and $Mo_2C$ of a nano meters on boundary of dendrite.

• Journal of the Korean Wood Science and Technology
• /
• 제34권5호
• /
• pp.59-66
• /
• 2006

The thermal properties of wood flour, Hwangto, and maleated polyethylene (MAPE) reinforced HDPE composites were investigated in this study. The thermal behavior of reinforced wood polymer composites was characterized by means of thermogravimetric (TGA) and differential scanning calorimetric (DSC) analyses. Hwangto and MAPE were used as an inorganic filler and a coupling agent, respectively. According to TGA analysis, the increase of wood flour level increased the thermal degradation of composites in the early stage, but decreased in the late stage. On the other hand, Hwangto reinforced composites showed the higher thermal stability than virgin HDPE, from the determination of differential peak temperature ($DT_p$). Decomposition temperature of wood flour and/or Hwangto reinforced composites increased with increase of heating rate. From DSC analysis, melting temperature of reinforced composites little bit increased with the addition of wood flour or Hwangto. As the loading of wood flour or Hwangto to HDPE increased, overall enthalpy decreased. It showed that wood flour and Hwangto absorbed more heat energy for melting the reinforced composites. Hwangto reinforced composites required more heat energy than wood flour reinforced composites and virgin HDPE. Coupling agent gave no significant effect on the thermal properties of composites. Thermal analyses indicate that composites with Hwangto are more thermally stable than those without Hwangto.

• 한국결정성장학회지
• /
• 제19권4호
• /
• pp.190-195
• /
• 2009

스컬용융법에 의해 Na사규소운모를 합성하였다. $Mg_3(OH)_2Si_4O_{10}:Na_2SiF_6:SiO_2=8.3:24.8:66.9$ mol% 비율로 혼합한 출발원료를 ${\phi}13{\times}H14cm$의 냉각도가니에 채우고 2.84MHz 출력주파수의 고주파발진기를 이용하여 가열하였다. 원료는 융액상태에서 1시간 유지하였으며 도가니 내에서 냉각시켰다. 운모의 비저항은 추정하였으며, 원주모양과 판상으로 합성할 수 있었다.

• 설비공학논문집
• /
• 제19권6호
• /
• pp.434-440
• /
• 2007

One of the cold start problems of a FCV is the freezing of the water in the water tank when a FCV is not in operation and the surrounding temperature drops below $0^{\circ}C$. The ice in the tank should be melted as quickly as possible for a satisfactory operation of fuel cell vehicles. In this study, the melting process for the constant heat fluxes of the plate heaters was numerically calculated in the 2-D model of the tank and plate heaters. The enthalpy method and FVM code was used for this analysis. The changes of the temperature with heat fluxes and the heat transfer area could be investigated. The energy balance error was found to increase with the heat flux. From this numerical analysis, the proper heat flux value and some important design factors relating local overheating and pressurization of the water tank could be examined.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.679-684
• /
• 2011

Recently, STS 301L joints of side panels to frames for stainless steel rolling stock have been made out by using existing welding methods including Resistance Spot Welding, Laser Welding and Arc Welding. Most of the processes were jointed by spot welding because it is faster at welding and comparatively less expensive for investment in welding facilities than other methods. During spot welding, however, indentation of the metal surface was made due to pressure and melting property of welding. Moreover, since the melting metal was forced to periphery of the plate as indentation was made, sheet separation, which cracked apart between jointed sheets, was carried out. A slight deformation which resulted from sheet separation deteriorated the emotional quality of railway vehicles. This paper suggests that by processing conventional spot electrode tip appropriately, melting metal is able to push up around the processed part (Hollow Spot Electrode Tip) and prevent from being dislodged from first place to periphery. Consequently, sheet separation is remarkably decreased. Also, the emotional quality of appearance of stainless steel rolling stock is enhanced considerably.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.226-234
• /
• 2009

The purpose of this study was to investigate the melting phenomenon of filler wire in detail and to obtain the precise temperature distribution of filler wire during GTA welding under the ultra-high welding speed condition in order to develop the ultra-high-speed GTA welding process with the pulse-heated hot-wire system by using three kinds of materials. The melting phenomenon of filler wire was observed using a high-speed camera and the temperature distribution of filler wire was measured using a radiation thermometer. From the above result, the adequate welding conditions of each material to make the GTA welding process with the ultra-high welding speed could be obtained. The ultra-high-speed GTA welding process needed the adequate wire current in order to obtain the adequate temperature distribution and the adequate melting position of filler wire. Moreover, the temperature distributions of three kinds of filler wire could be estimated by using the proposed simple estimation method.

• 한국주조공학회지
• /
• 제13권4호
• /
• pp.350-358
• /
• 1993

Aluminum base composites reinforced with various amount of SiC particles and Mg contents have been investigated by different fabrication method for twenty-years. In this paper, how the decomposition and dissolution behaviors of $SiCp(20{\mu}m)$ in the melt of Al composites arised was studied. As the results, the decomposition and dissolution of SiCp into the melt of Al composites increased with increase of the temperature above $720^{\circ}C$, and holding time at a given melting temperature. Because SiC is thermodynamically unstable in this Al-SiCp composite at temperature above the liquidus, SiCp dissolves and reacts with Al in matrix to form $Al_4C_3$ according to following chemical equation $4Al+3SiC{\rightarrow}Al_4C_3+3Si$, Si decomposed and dissolved from SiCp increases Si content of matrix, while liquidus temperature of matrix decrease with increase of SiC content in matrix. The hardness of SiCp decreased with increase of the melting temperature, the hardness of the matrix /particle interface increased with increase of the melting temperature due to increase of the $Mg_2Si$ and $Al_4C_3$ intermetallic compounds, etc.

• 한국군사과학기술학회지
• /
• 제23권3호
• /
• pp.195-203
• /
• 2020

Selective laser melting(SLM) is one of the powder bed fusion(PBF) processes, which enables quicker production of nearly fully dense metal parts with a complex geometry at a moderate cost. However, the process still lacks knowledge and the experimental evaluation of possible process parameter sets is costly. Thus, this study presents a finite element analysis model of the SLM process to predict the melt pool characteristics. The physical phenomena including the phase transformation and the degree of consolidation are considered in the model with the effective method to model the volume shrinkage and the evaporated material removal. The proposed model is used to predict the melt pool dimensions and validated with the experimental results from single track scanning process of Ti-6Al-4V. The analysis result agrees with the measured data with a reasonable accuracy and the result is then used to evaluated each of the process parameter set.