• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.1
• /
• pp.17-21
• /
• 2018

The natural frequency of a laminated cantilever microbeam was studied in the present investigation. The microbeam was made of quartz on a silicon chip, and its top and bottom surfaces were coated with thin(~30nm) gold films. An ultrasonic testing platform was employed to resonate the microbeam, and its time domain signal was optically measured. The natural frequency was quantified through the fast Fourier transform of the waveform, and the result showed good agreement with a theoretical estimation from the classical beam theory. This study is expected to provide a dynamic evaluation technique for micro/nanoscale materials and micromechanical structures.

• Journal of Power Electronics
• /
• v.18 no.5
• /
• pp.1501-1512
• /
• 2018

This paper proposes a three-phase three-switch buck-type converter as the MSC of a wind turbine system. Owing to a novel switching modulation scheme that can eliminate the unwanted diode rectifier mode switching state, the proposed system exhibits a satisfying ac voltage and current waveform quality and torque ripple up to the level of a typical current source rectifier even under a wide power factor operating range. The proposed system has been verified through simulations and HILS tests on a PMSG wind turbine model of 5MW/4160V. The proposed converter has been shown to provide a stator current THD of 3.9% and a torque ripple of 1% under the rated power condition. In addition to the inherent advantage of the reduced switch count of three-phase three-switch buck-type converters, the proposed switching modulation technique can make this converter a viable solution for the MSC placed inside of a nacelle, which is under severe volume, weight and mechanical vibration design limits.

• Journal of Biomedical Engineering Research
• /
• v.14 no.1
• /
• pp.31-40
• /
• 1993

It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propa gation characteristics of the internal vibration in the tissue for the low frequency mechanical vibra lion by using bispectral analysis is proposed. In the method, low frequency vibration of $f_0(=100Hz)$ is applied on the surface of the object, and the waveform of the internal vibration ${\times}{\;}(t)$ is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal ${\times}{\;}(t.)$ at the frequencies ($f_0,{\;}f_0$) and ($f_0,{\;}2f_0$) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, where since bispectrum is free from the gallssian additive noise we can get the value with high S/N. Basic experimental system is con structed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization.

• International Journal of Safety
• /
• v.11 no.2
• /
• pp.10-14
• /
• 2012

Recently, the combined power plants are refocused rapidly as a replaceable energy system of the nuclear power plant. The large turbine is revolved highly at 1800~3600 rpm. Thus, the turbine speed should be monitored with mechanical and electrical method for a safety. The electrical cutoff valve which blocks the flow channel with the electrical signal is with a built in. The aim of this study is to develop a manufacturing technology through by the localization of a solenoid actuated directional control valve. Especially the results show performances of the solenoid valve by the experiments and modeling and the reliability estimation. Applied load port pressure was changed rapidly on the form of a quadratic curve over time. And in the cases of square waveform when 0~100 V and 20~120 V input voltage, it was driven on a stable state until 13.4 Hz and 16.6 Hz, respectively. We think that this study will give useful data for the electricity safety system of the combined power plant gas turbine.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.305-309
• /
• 1999

This paper presents an high efficiency energy conversion system for very high-speed flywheel energy storage system using high Tc superconducting bearings. Main configuration of power convertor is designed to replace of the conventional battery with EMB(Electro Mechanical Battery). PMSM(Permanent Magnet Synchronous Motor) using Halbach array is used as the energy conversion system of motor and generator. Some PWM methods for the high frequency inverter is described and the power factor effects to the torque characteristics and efficiency of the motor and generator is analyzed. As the results, it is verified that the inverter output current is well regulated to be in-phase or inverse-phase sinusoidal waveform to have the wide operational range from 2,500rpm to 42,000rpm. Proposed circuit is designed to obtain the very high speed, high efficiency and stable rotational characteristics, and to be applied to1.2r[kW]/65[Wh] system.

• Journal of Welding and Joining
• /
• v.28 no.6
• /
• pp.28-34
• /
• 2010

This paper was described on investigation to prevent porosity in high speed MIG Welding of Al 6082-T6. Porosity measurement was carried out by using image analysis of micrographs with the help of an analysis software. The main parameter was arc length and torch progressive angle. The porosity ratio was increased as arc length was increased. The arc length was increased depending upon the output voltage. By proper selection of pulse waveform parameter, the stable arc of one pulse one drop was generated. The porosity ratio of optimum condition in one pulse one drop was lower than high voltage condition. When torch progressive angle was an angle of advance $10^{\circ}$, porosity ratio was minium.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.318-323
• /
• 2001

Characteristics of the pulsatile flow in a 3-dimensional elastic blood vessel are investigated to understand the blood flow phenomena in the human body arteries. In this study, a model for the elastic blood vessel is proposed. The finite volume prediction is used to analyse the pulsatile flow in the elastic blood vessel. Variations of the pressure, velocity and wall shear stress of the pulsatile flow in the elastic blood vessel are obtained. The magnitudes of the velocity waveforms in the elastic blood vessel model are larger than those in the rigid blood vessel model. The wall shear stresses on the elastic vessel vary with the blood vessel motions. Amplitude indices of the wall shear stress for blood in the elastic blood vessel are $4\sim5$ times larger than those of the Newtonian fluid. As the phase angle increased, point of the phase angle is are moved forward and the wall shear stresses are increased for blood and the Newtonian fluid.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.1
• /
• pp.53-61
• /
• 2011

Edge notched A16061-T6 aluminum was repaired with a GFRP composite patch as a function of the number of stacking, Damage progress of specimen for tension load has been monitored by acoustic emission(AE), AE energy rate, hit rate, amplitude, waveform and 1st peak frequency distribution were analyzed. Fracture processes were classified into Al cracking, Fiber breakage, Resin cracking and Delamination. Displacement of a specimen can be divided into Region I, II and ill according to acoustic emission characteristics. Region II where the patch itself was actually fractured was focused on to clarify the AE characteristics difference for the number of stacking.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.2
• /
• pp.28-33
• /
• 2003

The piezoelectric transformer converters electrical energy into mechanical energy, It is high efficiency and small size transformer for high output voltage. The piezoelectric transformer operates the resonance frequency and the output voltage waveform is close to sine wave. Therefore, it is suitable for driving the LCD backlight in the notebook computer. In this paper, we discussed about the inverter which os driving piezoelectric transformer by generating sine wave through LC resonance after converting input DC voltage to the gate signal of FET. As the result of experiments, it was showed that the resonance frequency and voltage gain of the piezoelectric transformer was proportional to the load variation, and voltage gain was independent of the input voltage variation.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.15 no.5
• /
• pp.19-24
• /
• 1978

In this paper, the functional propertied of vibrotactile sense of skin were studied by means of psycophysical experiments with respect to frequency and waveform of mechanical vibration, two-point threshold, contactor size of stimulators. Furthermore, leased on the experimental result, a small vibrotactile stimulator made of piezoelectrc ireed vibrator array was proposed for a aid blind to recognition of the Korean letters. A tactile output image is presented by an 8 row$\times$1 column array of samall vibrator reeds with 200 Hz rectangular wave, the array fitting on a fore-finger. Under the control of the NOVA mini-computer, the bimorph reeds array could represent any of one of the 24 characters of the Korean vowel and consonant at the 8 positions from left to right on the array. Without learning effect, the identification test of the Korean characters by the designed experimental system was carried out. The average rate of correct response was 90%.