• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.153-158
• /
• 2013

The purpose of this study is to investigate the performance characteristics of the counterflow exhaust heat recovery device for the applied gasoline engines. The EHRS device is installed behind the catalyst. This study investigates the engine warm-up characteristic, the exhaust noise characteristic, the back-pressure characteristic. The engine warm-up characteristics is (load 0%, load 10%, load 20%) in (idle, 1000rpm, 1500rpm, 2000rpm, 2500rpm) conditions by measuring the time it warmed up, coolant temperature ($25^{\circ}C{\sim}80^{\circ}C$) until the performance evaluation is performed. The wide open throttle and the coast down the exhaust noise and the back-pressure characteristic experiment repeated twice. The test conditions is 950rpm~6,050rpm proceed experiment repeated 3-5 times. Load 0% idle conditions except the results improved engine warm-up characteristics. The exhaust noise obtain similar results the BASE+EHRS W/O_FRT_MUFF with BASE and back-pressure to obtain similar results BASE+EHRS W/O_FRT_ MUFF with BASE+EHRS.

• 복식
• /
• 제58권1호
• /
• pp.1-8
• /
• 2008

The purpose of this study was to investigate the mechanical properties and hand values of polypropylene knit and to analyze its color-fastness for light, laundering and abrasion, comparing to nylon and polyester knits. The results of this study were as follows: 1. Polypropylene stretched more with less force than nylon and polyester and its elastic recovery and shape stability were better than nylon and polyester. 2. Polypropylene was more flexible than nylon and polyester. 3. Polypropylene stretched more easily for shearing but its recovery from shearing was less than nylon and polyester. 4. Polyester had smoother surface than nylon and polyester. 5. Polypropylene was compressed more easily than polyester with less force but less than nylon. Its recovery from compression was more than nylon and polyester. 6. Polypropylene had lower KOSHI and SHARI values and higher FUKURAMI value than nylon and polyester. It had better T.H.V. value than nylon but less than! polyester. 7. Color fastness of polypropylene for lanudering, light, and abrasion in wet and dry conditions was good except polypropylene dyed with red color.

• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1961-1971
• /
• 2006

A soft recovery system (SRS) is a device that stops a high speed projectile without damaging the projectile. The SRS is necessary to verify the shock resistant requirements of microelectronics and electro-optic sensors in smart munitions, where the projectiles experience over 20,000 g acceleration inside the barrel. In this study, a computer code for the performance evaluation of a SRS based on ballistic compression decelerator concept has been developed. It consists of a time accurate compressible one-dimensional Euler code with use of deforming grid and a projectile motion analysis code. The Euler code employs Roe's approximate Riemann solver with a total variation diminishing (TVD) method. A fully implicit dual time stepping method is used to advance the solution in time. In addition, the geometric conservation law (GCL) is applied to predict the solutions accurately on the deforming mesh. The equation of motion for the projectile is solved with the four-stage Runge-Kutta time integration method. A small scale SRS to catch a 20 mm bullet fired at 500 m/s within 1,600 g-limit has been designed with the proposed method.

• 대한조선학회논문집
• /
• 제53권3호
• /
• pp.195-200
• /
• 2016

In this study, compression tests for the polyisocyanurate foam which is recognized as the insulation material for the storage tank of the liquefied natural gas (LNG) were carried out for investigation of the material characteristic of mechanical behavior. Deformation recovery ratio according to the various initial deformation levels were estimated and the mechanical behavior of foams that are experienced compressive deformation was also obtained experimentally. The test results were analyzed based on the conditions of initially applied strain level and engineering strain rate.

• 대한가정학회지
• /
• 제40권7호
• /
• pp.15-24
• /
• 2002

In this work, the effect of fusible interlining on the appearance related properties and mechanical characteristics of Lyocell fabric after fusing was investigated. Two different types(20's and 10's) of Lyocell face fabric with six different interlining(by thickness and structure) for earth Lyocell fabric were examined. In order to establish the optimum fusing condition for the different face fabric and interlining, peel strength of each fused fabric was measured, which was dependent on the fusing temperature, pressure, and time. The characteristics related appearance and mechanical characteristics of each fused fabric were determined. The results are as follows: The peel strength was excellent, when the fabric was fused with the force of 3kgf/$textrm{cm}^2$ at $120^{\circ}C$ for 15seconds. Flex stiffness, G, 2HG, 2HG5(shear), B, 2HB(bending) of 100% Lyocell fabric 10's were higher than those of 100% Lyocell 20's. Flex stiffness, crease recovery, G, 2HG, B, 2HB of thicker woven interlining were higher than those of thinner woven interlining. Crease recovery of twill interlining were higher than those of plain interlining. In case of shear and bending properties, however, plain interlining was higher than twill interlining. Flex stiffness, crease recovery, G, 2HG, 2HG5, B, 2HB of nonwoven interlining were higher than those of woven interlining. In case of drapability, however, woven interlining was higher than nonwoven interlining.

• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.292-297
• /
• 1986

본 연구에서는 2024 Al 합금에 대하여 260-380.deg. C의 온도 범위 및 2~5kgf/ m $m^{2}$의 부과응력 범위에서 실시한 고온 정상 크리이프 변형 중의 내부응력 .sigma. $_{i}$,의탄성 변형 .epsilon.$_{A}$ 및 회복율 r의 측정 실험을 통하여 이들 상호간의 관계 를 살펴 보고자 한다.다.다.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.1002-1012
• /
• 2001

The work reported here is an extensive study of tendon response to multiple cyclic tests including 3% constant peak strain level test (A-type test), 3% constant peak strain level test with two rest periods (B-type test), and 3∼4% different peak strain level test (C-type test). A sufficient number of specimens were tested at each type of the test to statistically evaluate many changes in response during testing and differences in response between each type of the test. In cyclic tests, there were decreses (relaxations) in the peak stresses and hysteresis, increases in the slack strains, and during lower peak strain level (3%) cyclic block after higher peak strain level (4%) cyclic block in the C-type tests. Considering the results of this study and those of the other study of multiple cyclic tests with rest periods by Hubbard and Chun, 1985, recovery phenomena during the rest periods occurred predominantly at the beginning of the rest periods. Consistently in both studies, the effects of rest periods were small and transient compared to the effects of the cyclic extensions. The recovery with cycles at lower peak strain level (3%) after higher peak strain level (4%) in the C-type test has not been previously documented. This recovery seems to be a natural phenomena in tissue behavior so that collagenous structures recover during periods of decreased demand.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제9권3호
• /
• pp.27-35
• /
• 2001

Heat transfer characteristics of a heat exchanged for low temperature waste heat recovery using oscillating capillary tube heat pipe (OCHP) were evaluated against the charging ratio variation of working fluid and various working fluids. R-l42b, R-22 and R-290 were used as working a 2.6mm in outside diameter, 1.44mm in inside diameter with 101m length and 140 turns. Charging ratio of working fluid was 40% and 50%. water was used as secondary fluid. Inlet temperature and mass velocity for each secondary fluid were 297 K, 280 K and 9~27 $4kg/m^2s$, respectively. From experimental results, it was found that heat transfer performance of R-22 was higher than those of R-142b and R-290 and it was proportional to Figure of Merit for thermosyphon. As a result, it was thought that R-22 was the most reasonable working fluid of waste heat recovery for low temperature waste heat recovery.

• 한국태양에너지학회 논문집
• /
• 제37권5호
• /
• pp.27-37
• /
• 2017

In this study, an artificial solar simulator composed of a 2.5 kW Xe-Arc lamp and mirror reflector was used to carry out the solar thermal two step thermochemical water decomposition cycle which can produce high efficiency continuous hydrogen production. Through various operating conditions, the change of hydrogen production due to the possibility of a dual-zone reactor and heat recovery were experimentally analyzed. Based on the reaction temperature of Thermal-Reduction step and Water-Decomposition step at $1,400^{\circ}C$ and $1,000^{\circ}C$ respectively, the hydrogen production decreased by 23.2% under the power off condition, and as a result of experiments using heat recovery technology, the hydrogen production increased by 33.8%. Therefore, when a thermochemical two-step water decomposition cycle is conducted using a dual-zone reactor with heat recovery, it is expected that the cycle can be operated twice over a certain period of time and the hydrogen production amount is increased by at least 53.5% compared to a single reactor.

• Journal of Electrical Engineering and Technology
• /
• 제11권4호
• /
• pp.839-847
• /
• 2016

Energy recovery battery testing systems (ERBTS) have been widely used in battery manufactures. All the ERBTS are connected in parallel which forms a special and complicated micro-grid system, which has the shortcomings of low energy recovery efficiency, complex grid-connected control algorithms issues for islanded detection, and complicated power circuit topology issues. To solve those shortcomings, a DC micro-grid system is proposed, the released testing energy has the priority to be reutilized between various testing system within the local grid, Compared to conventional scheme, the proposed system has the merits of a simplified power circuit topology, no needs for synchronous control, and much higher testing efficiency. The testing energy can be cycle-used inside the local micro-grid. The additional energy can be recovered to AC-grid. Numerous experimental comparison results between conventional and proposed scheme are provided to demonstrate the validity and effectiveness of the proposed technique.