• Polymer(Korea)
• /
• v.35 no.3
• /
• pp.189-195
• /
• 2011

The design of new bioactive scaffolds offering physiologic environment for tissue formation is an important frontier in biomaterials research. In this study, we performed compressive strength, water-uptake ability, and SEM analysis for physical property assessment of 3-D silk/PLGA scaffold, and investigated the adhesion, proliferation, phenotype maintenance, and inflammatory responses of RAW 264.7 and NIH/3T3 for cell compatibility. Scaffolds were prepared by the solvent casting/salt leaching method and their compressive strength and water-uptake ability were excellent at 20 wt% silk content. Result of cell compatibility assay showed that inflammatory responses distinctly decreased, and initial adhesion and proliferation were maximized at 20 wt% silk content. In conclusion, we suggest that silk/PLGA scaffolds may be useful to tissue engineering applications.

• Tunnel and Underground Space
• /
• v.8 no.4
• /
• pp.307-320
• /
• 1998

Tunnel lining is the final support of a tunnel and reflects the results of the interaction between ground and support system. Recently it is very difficult to support and manage the tunnel because the cracks on tunnel lining cause many problems in supporting and managing tunnels. Therefore the analysis of the cracks is quite strongly required. In this study, mechanical behaviour of a tunnel lining was examined by model tests and by numerical analyses. Especially the model test was examined for double linings including shotcrete and concrete lining. The model tests were carried out under various conditions taking different loading shapes, horizontal stresses, thicknesses of linings and double lining, vault opening behind the concrete lining and rock-like medium surrounding the lining. Due to horizontal stress, compressive stress prevailed on the lining. Thus the bearing capacity of the lining increased. The existence of a vault opening behind the concrete lining reduced the bearing capacity by the similar amount of reduction of concrete lining thickness. Rock-like medium cast around the side wall of the lining restrained the deflection of the lining, and the bearing capacity for cracking and failure increased vary much. In numerical analyses a algorithm which can analysis the double lining by introduction of interface element was developed. And the results of the numerical analyses were compared with the results of the model tests.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.4
• /
• pp.89-94
• /
• 2008

Purpose: To observe the high temperature creep test and the fracture surface of the samples of 9% Ni alloy steel generally used for all kinds of mahine parts and predict the durability of that by determining a constant of C with a Larson-Miller variable. Methods: The equipment of this test was made into lever-beam style designed by Andrade and F. Garofalo et al.. The condition of creep test was set under 16 kinds of conditions after fixing 4 kinds of temperature condition and 4 kinds of stress condition to check how it effects the samples. Results: The temperature of creep test was increased, the stress index (n) of creep deformation was gradually decreased from 3.97 to 3.55. The activation energy of creep deformation was decreased from 90.39 to 83.64 kcal/mol when the stress was increased. A constant of C value by calculation of larson-Miller variable was about 22 and if temperature for use is suggested, the durability could be calculated. Conclusions: By analyzing the fracture phenomenon and suggesting the observation result of the fracture surface of the samples and creep test of 9% Ni alloy steel, the basic design data for the practical use of accessories in the field of equipment could be constructed and used to predict the durability of the equipment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.212-219
• /
• 2003

This study is to evaluate the characteristics of SCC at the welded region of high strength steel using acoustic emission(AE) method. Specimens were loaded by a slow strain rate method in synthetic seawater and the damage process was monitored simultaneously by AE method. Corrosive environment was controlled using the potentiostat, in which -0.8V and -1.1V were applied to the specimens. In the case of one-pass weldment subjected to -0.8V, much more AE counts were detected compared with the PWHT specimen. It was verified through the cumulative counts that coalescence of micro cracks and cracks for the one pass weldment with -0.8V were mostly detected. In case of the one pass weldment subjected to -1.1V, time to failure became shorter and AE counts were produced considerably as compared with that of the two pass weldment. It was shown that AE counts and range of AE amplitude have close relations with the number and size as well as width of the cracks which were formed during the SCC.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.1
• /
• pp.18-26
• /
• 2016

The semiconductor industry is one of the key industries of Korea, which has continued growing at a steady annual growth rate. Important technology for the semiconductor industry is high integration of devices. This is to increase the memory capacity for unit area, of which key is photolithography. The photolithography refers to a technique for printing the shadow of light lit on the mask surface on to wafer, which is the most important process in a semiconductor manufacturing process. In this study, the width and step-height of wafers patterned through this process were measured to ensure uniformity. The widths and inter-plate heights of the specimens patterned using photolithography were measured using transmissive digital holography. A transmissive digital holographic interferometer was configured, and nine arbitrary points were set on the specimens as measured points. The measurement of each point was compared with the measurements performed using a commercial device called scanning electron microscope (SEM) and Alpha Step. Transmission digital holography requires a short measurement time, which is an advantage compared to other techniques. Furthermore, it uses magnification lenses, allowing the flexibility of changing between high and low magnifications. The test results confirmed that transmissive digital holography is a useful technique for measuring patterns printed using photolithography.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.3
• /
• pp.195-201
• /
• 2016

Eddy current testing (ECT) is commonly applied for the inspection of automated production lines of metallic products, because it has a high inspection speed and a reasonable price. When ECT is applied for the inspection of a metallic object having an uneven target surface, such as the spline gear of a spline shaft, it is difficult to distinguish between the original signal obtained from the sensor and the signal generated by a defect because of the relatively large surface signals having similar frequency distributions. To facilitate the detection of defect signals from the spline gear, implementation of high-order filters is essential, so that the fault signals can be distinguished from the surrounding noise signals, and simultaneously, the pass-band of the filter can be adjusted according to the status of each production line and the object to be inspected. We will examine the infinite impulse filters (IIR filters) available for implementing an advanced filter for ECT, and attempt to detect the flaw signals through optimization of system design parameters for detecting the signals at the system level.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.2
• /
• pp.148-154
• /
• 2014

Photoelasticity is a useful technique for obtaining the differences and directions of principal stresses in a model. In conventional photoelasticity, the photoelastic parameters are measured manually point by point. Identifying and measuring photoelastic data is time-consuming and requires skill. The fringe phase shifting method was recently developed and has been found to be convenient for measuring and analyzing fringe data in photo-mechanics. This paper presents an experimental study on the stress distribution along a horizontal line that passes the central point of a rhombus plate made of Photoflex (i.e., type of urethane rubber). The isoclinic fringe and/or principal stress direction is constant on this horizontal line, so a four-bucket phase shifting method can be applied. The method requires four photoelastic fringes that are obtained from a circular polariscope by rotating the analyzer at $0^{\circ}C$, $45^{\circ}C$, $90^{\circ}C$ and $135^{\circ}C$. Experimental measurements using the method were quantitatively compared with the results from FEM analysis; the results from the two methods showed comparable agreement.

• Korean Journal of Food Science and Technology
• /
• v.48 no.5
• /
• pp.461-465
• /
• 2016

In order to prevent the blackening and texture softening of heated shrimp, the pH was adjusted by soaking shrimps in acidic and alkali solutions, and their qualities were evaluated. The lightness of shrimps pretreated with 0.2% (w/w) citric acid and 0.05% (w/w) ascorbic acid solution increased by 20% compared to that of the control. The strength of mechanical hardness of shrimps soaked in acetic acid and phosphate solution (pH 6.0) was significantly higher ($1209g_f$) compared to that of untreated shrimp ($801g_f$; p<0.05), and the overall preference of texture was 0.4 points higher than that of the control in the descriptive sensory evaluation (p<0.05). In contrast, soaking in solution of pH 8 exhibited a weak texture hardening effect ($855g_f$). Additionally, the hardness of the heated shrimp after soaking at an adjusted pH of 4.0 increased to $4046g_f$, but the yield based on weight decreased to 38% compared to that of untreated shrimp (70%; p<0.05).

• Korean Journal of Food Science and Technology
• /
• v.28 no.1
• /
• pp.169-178
• /
• 1996

Target parameters such as water solubility index (WSI), intrinsic viscosity (IV), water holding capacity (WHC), oil holding capacity (OHC), soluble dietary fiber (SDF) and microstructure were investigated on three different screw configurations during twin-screw extrusion of wheat bran. WSI of raw wheat bran (RWB) was 13.7%, while that of extrudates ranged $16.3{\sim}23.2%$ when extruded using screw configurations with 5 reverse screw elements (RSE). It was found that the moisture content of RWB greatly affected WSI of extrudates. IV of wheat bran extrudates increased from 10.6 ml/g of RWB to $37.86{\sim}44.37\;ml/g$ of extrudates extruded using 3, 4 and 5 RSE, whose trend was highly related to the moisture content of RWB and the extrusion pressure. Multiplication of IV and soluble solid (SS) content exhibited good correlation $(R^2=0.85)$ with specific mechanical energy (SME). The results suggested that SS and molecular size are an important factor governed by the SME in solubilization of wheat bran. WHC increased with increasing feed rate and moisture content, while OHC decreased. SDF increased from 2.68% of RWB to $4.32{\sim}6.48%$ of extruded wheat bran, indicating the significant breakdown of cell wall components. Microstructure of the extrudates showed the distinct patterns of degradation and solubilization of cell wall structure, depending on the moisture content of RWB.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.300-309
• /
• 2016

Curved beams are increasingly used in buildings, vehicles, ships, and aircraft, which has resulted in considerable effort towards developing an accurate method for analyzing the dynamic behavior of such structures. The stability behavior of elastic curved beams has been the subject of many investigations. Solutions to the relevant differential equations have traditionally been obtained by the standard finite difference or finite element methods. However, these techniques require a great deal of computer time for a large number of discrete nodes with conditions of complex geometry and loading. One efficient procedure for the solution of partial differential equations is the differential quadrature method (DQM). This method has been applied to many cases to overcome the difficulties of complex algorithms and high storage requirements for complex geometry and loading conditions. Out-of-plane buckling of curved beams with rotatory inertia were analyzed using DQM under uniformly distributed radial loads. Critical loads were calculated for the member with various parameter ratios, boundary conditions, and opening angles. The results were compared with exact results from other methods for available cases. The DQM used only a limited number of grid points and shows very good agreement with the exact results (less than 0.3% error). New results according to diverse variation are also suggested, which show important roles in the buckling behavior of curved beams and can be used for comparisons with other numerical solutions or experimental test data.