• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.1-2
• /
• 2006

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.138-142
• /
• 2003

The conditions for measurement of the interior noise should meet the international standards. However, due to the limitations in test conditions the possible errors in measurement equipment, reliability of the measurement results has been questioned. Hence, the test procedure for the interior noise measurement of KTX vehicles are reviewed and investigated with the reference of international standards. Furthermore, the acceptable tolerance is inspected through the analysis of the factors that influence the interior noise of the KTX vehicle.

• Journal of Sensor Science and Technology
• /
• v.29 no.2
• /
• pp.128-132
• /
• 2020

Total organic carbon (TOC) analysis equipment, which was previously used to prevent eutrophication in advance, is heavy, bulky, and expensive; therefore, so it is difficult to be carried and has been used as an experimental unit. In this study, a through-carbon analysis chip that integrates pretreatment through photocatalytic oxidation and carbon dioxide measurement using a pH indicator was investigated. Both the total carbon - inorganic carbon method and the nonpurgeable organic carbon (NPOC) measurement method require an acidification part for injecting an acid solution for inorganic carbon measurement and removal, an oxidation part for total carbon or NPOC oxidation and a measurement part for Carbon dioxide (CO₂) measurement. Among them, the measurement of oxidation and CO₂ requires physical technology. The proposed TOC analysis chip decomposed into CO₂ as a result of the oxidizing of organic carbon using a photocatalyst, and the pH indicator that was changed by the generated CO₂ was optically measured. Although the area of the sample of the oxidation part and the pH indicator of the measurement part were distinguished in an enclosed space, CO₂ was quantified by producing an oxidation part and a measurement part that shared the same air in one chip. The proposed TOC analysis chip is less expensive and smaller, cost and size are disadvantages of existing organic carbon analysis equipment, because it does not require a separate carrier gas to transport the CO₂ gas in the oxidation part to the measurement part.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.178-180
• /
• 2016

TMDE(Test Measurement and Diagnostic Equipment) which is using in the military weapon system should perform the periodic calibration to maintain a measurement reliability during the life cycle, organizations are faced with increasing pressures to minimize costs while improving the reliability of test equipment. Previous studies suggest that reliability models are determined by considering simple size and characteristics of equipment, however an applying single Model may not be fit well maintenance data of many kinds of TMDEs. This paper presents that recommending an optimal calibration interval through the goodness of fit test with verifying statistical significance level among the several intervals which are computed with using major reliability models. According to the result of applying the actual proposed of calibration interval analysis method for various types of equipment, reliabilities are maintained for the end of calibration intervals.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.799-800
• /
• 2013

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.1
• /
• pp.7-15
• /
• 2011

In this paper, we implement measurement functionality for the 3GPP (Third Generation Partnership Project) WCDMA (Wideband Code Division Multiple Access) modem. Generally speaking, the receiving algorithms in normal modems cannot be used directly to the measurement system due to the lack of the measurement accuracy. In this paper, we propose the new measurement algorithm for precise 3GPP WCDMA signal measurements. In the measurement algorithm, 4-stage parameters estimation scheme is used. To improve the measurement accuracy, we increase the number of the received signal samples by interpolation. The proposed 3GPP WCDMA signal measurement algorithm can be used for verifying and implementing SoC/FPGA modem measurement systems.

• Proceedings of the IEEK Conference
• /
• 2000.07a
• /
• pp.233-236
• /
• 2000

A portable equipment that measures a current and voltage waveform of power transmission lines is pro-posed. In the equipment, the current and voltage, respectively, are detected by a loop coil and a capacitor clamped around the power lines. The detected data is transmitted by an FM wave to the receiver on the ground station. Since the receiver is isolated from the power lines, we do not require high potential insulators for the measurement of current and voltage. The proposed equipment is therefore, small-sized, light, and low in the cost of production. Experimental results presented here show that the equipment can monitor the current flowing in single wire over a ground plane and the potential of the wire.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.761-766
• /
• 1998

GPR(Ground Penetrating Radar) designed with a digital-based signal processing technology utilizes to identify very easily the location, the thickness and the level of either an underground embedment or an underground structure. Prior to use of this GPR equipment on pavement of about 15cm thick, the equipment should foremost be calibrated on a known sample under known condition. The purpose of this study is to verify the applicability of the GPR equipment to a model pavement of about 15cm thick. As part of this effort, the general approach of this study is to verify the applicability of the GPR equipment by various thickness levels and its error ranges thru a statistical analysis.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.100-101
• /
• 2018

Environmental problems caused by air pollution have been considered as serious critical issues in global perspectives. Controlling greenhouse gases has become one of the major environmental problems in construction fields as well. However, similar studies were mainly focused on suggestion of various methodologies for measuring CO₂ emissions of construction equipment and calculating emissions. This study aims to analyze the correlation between the CO₂ emissions and RPMs of equipment by the construction process based on row data collected from construction equipment actually operated in job sites. This study allows site personnels to determine the amount of emitted CO₂ under particular construction equipment under specific conditions during the targeted construction operations. The research findings expect to be used as fundamental informations for establishing environment-friendly construction operation planning.

• International journal of advanced smart convergence
• /
• v.11 no.4
• /
• pp.216-226
• /
• 2022

In this study, we selected and trained 9 people in the diaphragm training group and 9 people in the power-breath training group among elderly people aged 65 or older living in the community, and investigated the effect of combined training using respiratory equipment on lung function, balance, and life satisfaction. We conducted the elderly to do combined exercises, twice a week for a total of 6 weeks, that include the breathing training by diaphragm, the breathing training using Power-breath equipment, and the training using a theraband. We evaluated the changes in the lung function, the balance, and the life satisfaction before and after the intervention for our study subjects.As a result of our measurement, lung function, balance, and life satisfaction showed significant changes in the experimental group that performed the combined training using Power-breath equipment. As a result of the study, we confirmed that the elderly in the community had a positive effect on the life satisfaction by improving lung function and balance ability after conducting a combined training using respiratory equipment.