• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.989-996
• /
• 2011

An understanding of the concentrated solar flux is critical for the analysis and design of solar-energy-utilization systems. The current work focuses on the development of an algorithm that uses the Monte Carlo ray-tracing method with excellent flexibility and expandability; this method considers both solar limb darkening and the surface slope error of reflectors, thereby analyzing the solar flux. A comparison of the modeling results with measurements at the solar furnace in Korea Institute of Energy Research (KIER) show good agreement within a measurement uncertainty of 10%. The model evaluates the concentration performance of the KIER solar furnace with a tracking accuracy of 2 mrad and a maximum attainable concentration ratio of 4400 sun. Flux variations according to measurement position and flux distributions depending on acceptance angles provide detailed information for the design of chemical reactors or secondary concentrators.

• Journal of Broadcast Engineering
• /
• v.19 no.2
• /
• pp.215-226
• /
• 2014

The 3D technology has been spread slowly and the reason would be attributed to the fact that most commercialized 3D displays require 3D glasses. There have been various researches on human factors of glass type 3D display. In this study we measured and modeled crosstalk as well as 3D visual fatigue induced by mobile glassless 3D display. Crosstalk as well as visual fatigue varied depending on horizontal position of the 3D mobile display. Measured crosstalk was relative low around the center of the display and it increased at the side of the display. Similar results were found in the measurement of 3D visual fatigue and discomfort. These results imply that human factors should be considered in the process of design and evaluation of mobile 3D displays.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.5
• /
• pp.787-794
• /
• 2001

In this paper, the development of large-signal model extractor for GaAs FET device through the Monolithic Microwave integrated Circuit(MMIC) is presented. The measurement program controlled by personal computer is developed for the processing of an amount of measured data, and the de-embedding algorithm is added to the program for voltage dropping as attached series resistance on measurement system. The small-signal model parameters are typically consisted of 7 elements that are considered as complexity of large-signal model and its the accuracy of the small-signal model is verified through comparing with measured data as varied bias point. The fitting function model, one of the empirical model, is used for quick simulation. In the process of large-signal model parameter extraction, one-dimensional optimization method is proposed and optimized parameters are extracted. This study can reduce the modeling and measuring time and can secure a suitable model for circuit.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.3
• /
• pp.315-325
• /
• 2017

The design dimension may not be satisfactory at the final stage due to the welding during the assembly stage, leading to cutting or adding the components in large structure constructions. The productivity is depend on accuracy of the welding quality especially at assembly stage. Therefore, it is of utmost importance to decide the component dimension during each assembly stage considering the above situations during the designing stage by exactly predicting welding deformation before the welding is done. Further, if the system that predicts whether welding deformation is equipped, it is possible to take measures to reduce deformation through FE analysis, helping in saving time for correcting work by arresting the parts which are prone to having welding deformation. For the FE analysis to predict the deformation of a large steel structure, calculation time, modeling, constraints in each assembly stage and critical welding length have to be considered. In case of fillet welding deformation, around 300 mm is sufficient as a critical welding length of the specimen as proposed by the existing researches. However, the critical length in case of butt welding is around 1000 mm, which is far longer than that suggested in the existing researches. For the external constraint, which occurs as the geometry of structure is changed according to the assembly stage, constraint factor is drawn from the elastic FE analysis and test results, and the magnitude of equivalent force according to constraint is decided. The comparison study for the elastic FE analysis result and measurement for the large steel structure based on the above results reveals that the analysis results are in the range of 80-118% against measurement values, both matching each other well. Further, the deformation of fillet welding in the main plate among the total block occupies 66-89%, making welding deformation in the main plate far larger than the welding deformation in the longitudinal and transverse girders.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.3 s.36
• /
• pp.267-274
• /
• 2005

This paper presents the fabrication of surface acoustic wave (SAW)-based pressure sensor for long-term stable mechanical compression force measurement. SAW pressure sensor has many attractive features for practical pressure measurement: no battery requirement, wireless pressure detection especially at hazardous environments, and easy other functionality integrations such as temperature, humidity, and RFID. A $41^{\circ}$ YX $LiNbO_3$ piezoelectric substrate was used because of its high SAW propagation velocity and large values of electromechanical coupling factors $K^2$. A silicon substrate with $\~200{\mu}m$ deep cavity was bonded to the diaphragm with epoxy, in which gold was covered all over the inner cavity in order to confine electromagnetic energy inside the sensor, and provide good isolation of the device from its environment. The reflection coefficient $S_{11}$ was measured using network analyzer. High S/N ratio, sharp reflected peaks, and clear separation between the peaks were observed. As a mechanical compression force was applied to the diaphragm from top with extremely sharp object, the diaphragm was bended, resulting in the phase shifts of the reflected peaks. The phase shifts were modulated depending on the amount of applied mechanical compression force. The measured $S_{11}$ results showed a good agreement with simulated results obtained from equivalent admittance circuit modeling.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.161-166
• /
• 2006

Vertical gravity gradient measurement offers greater structural resolution and detectability than gravity alone. Practical difficulties of field measurement of vertical gravity gradient have raised questions of its accuracy and utility. But, modern automated gravimeter of $1\;{\mu}Gal$ sensitivity makes it easier to measure vertical gradient with required accuracy. It is particularly effective to engineering and environmental problems which target shallow subsurface structure. This paper attempts to apply the vertical gravity gradient technique to high resolution density mapping. The method was generally reviewed and numerical inverse modeling was executed for comparing with conventional gravity. And actual vertical gravity gradient data surveyed overt karstic cavity area at Muan was analysed and interpreted.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.33-38
• /
• 2008

Most structures of vehicle are composed of many substructures connected to one another by various types of mechanical joints. In vehicle engineering, it is important to study these jointed structures under random frequency vibration for the evaluations of fatigue life and stress concentration exactly. It is rarely obtained the accurate load history of specified positions in a jointed structure because of the errors such as modeling, measurement, and etc. In the beginning of design, exact load data are actually necessary for the fatigue strength and life analysis to minimize the cost and time of designing. In this paper, the hybrid method of practical dynamic load determination is developed by the combination of the principal stresses from F. E. Analysis and test of a jointed structure. Least square pseudo inverse matrix is adopted to obtain an inverse matrix of analyzed stresses matrix. The error minimization method utilizes the inaccurate measured error and the shifting error that the whole data is stiffed over real data. The least square criterion is adopted to avoid these errors. Finally, to verify the proposed system, a heavy-duty bus is analyzed. This measurement and prediction technology can be extended to the different jointed structures.

• Korean Journal of Geomatics
• /
• v.1 no.1
• /
• pp.1-5
• /
• 2001

This paper presents an investigation into the operational comparison of SPOT triangulation to build GCP library by analytical plotter and DPW (digital photogrammetric workstation). GCP database derived from current SPOT images can be used to other image sensors of satellite, if any reasons, such as lack of topographic maps or GCPs. But, general formulation of a photogrammetric process for GCP measurement has to take care of the scene interpretation problem. There are two classical methods depending on whether an analytical plotter or DPW is being used. Regardless of the method used, the measurement of GCPs is the weakest point in the automation of photogrammetric orientation procedures. To make an operational comparison, five models of SPOT panchromatic images (level 1A) and negative films (level 1AP) were used. Ten images and film products were used for the five GRS areas. Photogrammetric measurements were carried out in a manual mode on P2 analytical plotter and LH Systems DPW770. We presented an approach for exterior orientation of SPOT images, which was based on the use of approximately eighty national geodetic control points as GCPs which located on the summit of the mountain. Using sixteen well-spaced geodetic control points per model, all segments consistently showed RMS error just below the pixel at the check points in analytical instrument. In the case of DPW, half of the ground controls could not found or distinguished exactly when we displayed the image on the computer monitor. Experiment results showed that the RMS errors with DPW test was fluctuated case by case. And the magnitudes of the errors were reached more than three pixels due to the lack of image interpretation capability. It showed that the geodetic control points is not suitable as the ground control points in DPW for modeling the SPOT image.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.3
• /
• pp.168-174
• /
• 2016

A conductive oxide-based sapphire glass indium tin oxide/metal electrode and the optical coating, through patterning process was studied in excellent optical properties and integrated touch panel has a high strength. Indium tin oxide conductive oxides of the sapphire glass to 0.3 A at DC magnetron sputtering method of 10 min, gas flow Ar 10 Sccm Ar, $O_2$ 1.0 Sccm the formation conditions of the thin film after annealing at $550^{\circ}C$ for 30min was achieved through a 86% transmittance. In addition, the coating 130 nm hollow silica sol-gel was to improve the optical transmittance of the indium tin oxide to 91%. For the measurement by the modeling hollow silica sol by Macleod simulation and calculated the average values of silica part to the presence or absence in analogy to actual. Refractive index value and the actual value of the material on the simulation the transmittance difference is it does not completely match the air region similar to the actual value (transmission) could be confirmed that the measurement is set to a value of between 5 nm and 10 nm.

• The Journal of the Korea Contents Association
• /
• v.19 no.5
• /
• pp.553-561
• /
• 2019

In this study, the method of quality measurement for the statistical usefulness of de-identified data was examined in terms of prediction accuracy by statistical modeling. In the era of the 4th industrial revolution, effective use of big data is essential to innovation through information and communication technology, but personal information issues are constrained to actively utilize big data. In order to solve this problem, de-identification guidelines have been established and the possibility of actual re-identification of personal information has become very low due to the utilization of various de-identification methods. On the other hand, strong de-identification can have side effects that degrade the usefulness of the data. We have studied the quality of statistical usefulness of the de-identified data by KLT model which is a representative de-identification method, A case study was conducted to see how statistical accuracy of prediction is degraded by de-identification. We also proposed a new measure of data usefulness of the de-identified data by quantifying how much data is added to the de-identified data to restore the accuracy of the predictive model.