• 보존과학연구
• /
• 통권20호
• /
• pp.49-64
• /
• 1999

According to damage of papers by the chemical cause, papers become to acidify. Among the 3 kinds of method measuring the acidity of paper, one was nondestructive method measuring the surface of the paper by flat type electrode and the others were destructive methods measuring directly by cold water extract method and hot water extract method. In case of the cellulolytic cultural properties, the latter methods were not applied because those methods must bedissociated papers. To measure the paper acidity nondestructively, we investigated the correlation of the nondestructive method and the destructive methods. The conclusions are as follows. 1) In the relationship of the cold water extract method and the hot water extract method, It was indicated that the pH measured by the hot water extract method was high quality printing paper 0.08, rough printing paper 0.13, and Korean paper 0.29 higher than that by the cold water extract method.2) In the relationship of the cold water extract method and the surface measurement method, It showed that the pH value measured by the cold water extract method was high quality printing paper 1.86, rough printing paper 0.80,and Korean paper 0.58 higher than value that by the surface measurement.3) In the relationship of the hot water extract method and the surface measurement method, It showed that the pH value measured by the hot ABSTRACT water extract method was high quality printing paper 1.78, rough printing paper 0.66, and Korean paper 0.29 higher than that by the surface measurement. From the above-mentioned results, the pH value measured by the surface measurement was need to high about 1.78∼1.86 in high quality printing paper, 0.66-0.80 in rough printing paper, and 0.29∼0.58 in Korean paper and the surface measurement with flat type electrode was very available to measure the acidity of Korean papers actually.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 추계학술대회 논문집
• /
• pp.546-551
• /
• 2001

We analysed the affection to subgrade that railway underground crossing construction make with studying displacement of subgrade of each construction methods and processing of Front jacking method and Pipe roof method with already-measured data(during the construction) and additionally-measured field test data in railway underground crossing construction. We measured vertical and horizontal displacement at two construction places of front jacking method and pipe roof method each, and we analysed the results of the measurement at each stage of construction to applied to the excution of construction.

• 한국정밀공학회지
• /
• 제17권7호
• /
• pp.156-161
• /
• 2000

Least Squares and Minimum Zone method are known for obtaining a datum or a continuous approximate function of measured data. This study is for a Minimum Zone algorithm for a circle, which is useful to obtain the exact roundness from the reference circle of measured data. The proposed method is compared with the Least Squares Limacon method and Chrystal-Peirce algorithm. A computational algorithm for the Minimum Zone circle is suggested and results in less roundness than the other two methods. This Minimum Zone circle method will be used for other geometrical measured data, such as plane or sphere for obtaining the exact flatness or sphericity.

• 한국식생활문화학회지
• /
• 제34권6호
• /
• pp.761-770
• /
• 2019

Two experiments were conducted to determine how much sodium in food could be detected using a salinity meter. First, the salinity of mixed solutions of 0 to 6% sugar, 0 to 5% oil, and 0 to 6.4% MSG in a 1% NaCl solution was measured using a salinity meter and a Mohr titration method, and the results were compared with the calculated sodium expectations. As a result, the sodium contents of the sugar solutions and MSG solutions measured using a salinity meter were lower than the expected concentrations at 2% or more and 0.8% or more, respectively (p<0.05). The salinity of the 18 HMR products was measured in the same way, and the results were then compared with the sodium contents of the nutrition facts. The average sodium content of all products measured using the salinity meter and Mohr method was 1.12 times and 1.06 times the sodium content of the nutrition facts, respectively. On the other hand, the differences between the products were significant. The correlation coefficients between the nutrition facts and salinity meter, the nutrition facts and the Mohr method, and the salinity meter and Mohr method were 0.885, 0.920, and 0.950, respectively (p<0.01).

• Smart Structures and Systems
• /
• 제23권2호
• /
• pp.195-205
• /
• 2019

An accurate non-model-based method for delamination identification of laminated composite plates is proposed in this work. A weighted mode shape damage index is formulated using squared weighted difference between a measured mode shape of a composite plate with delamination and one from a polynomial that fits the measured mode shape of the composite plate with a proper order. Weighted mode shape damage indices associated with at least two measured mode shapes of the same mode are synthesized to formulate a synthetic mode shape damage index to exclude some false positive identification results due to measurement noise and error. An auxiliary mode shape damage index is proposed to further assist delamination identification, by which some false negative identification results can be excluded and edges of a delamination area can be accurately and completely identified. Both numerical and experimental examples are presented to investigate effectiveness of the proposed method, and it is shown that edges of a delamination area in composite plates can be accurately and completely identified when measured mode shapes are contaminated by measurement noise and error. In the experimental example, identification results of a composite plate with delamination from the proposed method are validated by its C-scan image.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 춘계학술대회 및 공장견학
• /
• pp.39-53
• /
• 1993

The minimum oil film thickness(MOFT) in the connecting-rod bering of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film charactrtistics. And cylinder pressure, crank-pin surface temperature and bearing tenp ture are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable detmuuination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• 한국추진공학회지
• /
• 제8권4호
• /
• pp.9-15
• /
• 2004

지상연소시험 후 측정된 추력은 시험대의 동특성으로 인해 실제 추력과는 달리 과도진동이 중첩되어 왜곡된 형태를 나타낼 수 있다. 본 연구에서는 왜곡된 추력을 보상하기 위해 측정된 추력만을 이용해 로켓모터의 실제 추력을 계산하는 방법을 제안하였고, 제안한 방법을 실험을 통해서 얻은 데이터에 적용하여 타당성을 입증하였다. 먼저 시험대 운동방정식을 이산시간 데이터 해석에 적합하도록 차분식으로 근사시키고, 시험대 특성 파라메타를 대수감소율 방법을 이용해 추정하였다. 그리고 측정추력과 추정한 시험대 파라메타 정보를 이용하여 시험대 변위를 계산한 후 차분식에 적용하여 실제추력을 계산하였다. 결과, 측정된 추력 이외에 다른 물리량을 측정하지 않고서 단지 측정된 추력 데이터만을 이용하더라도 시험대 과도응답이 제거된 실제 추력을 계산할 수 있었다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제44권5호
• /
• pp.435-441
• /
• 2021

The purpose of this study was to evaluate the quality of images and to quantitatively measure and analyze the dose of scattered ray to the organs, which were highly sensitive to radiation according to the use of cylinder cone in mastoid process radiography. When the cylinder cone was not used, the SID was 100cm and the field size was 24 × 36 cm(864 cm²). When using the cylinder cone which was a circle, the SID was 70 cm, the radius was 10.5 cm and field size was 86.59 cm². As a result of the study, SNR of the image quality evaluation was measured to be 2.58 for Law method and 3.90 for Stenver's method when not using cylinder cone, and 2.87 for Law method and 14.67 for Stenver's method when using cylinder cone. CNR was measured to be 0.03 for Law method and 0.04 for Stenver's method when cylinder cone was not used, and 0.04 for Law method and 0.05 for Stenver's method when using cylinder cone. When the cylinder cone was not used, the scattered ray dose was measured to be 0.10 mGy in the right eyeball, 0.30 mGy in the left eyeball, 2.02 mGy in the parotid gland, and 0.29 mGy in the thyroid gland for Law method and to be 0.03 mGy in the right eyeball, 0.12 mGy in the left eyeball, 1.43 mGy in the parotid gland, and 0.09 mGy in the thyroid gland for Stenver's method. When the cylinder cone was used, the scattered ray dose was measured to be 0.05 mGy in the right eyeball, 0.03 mGy in the left eyeball and the parotid and thyroid gland were below the measurable values for Law method and all areas were below the measurable values for Stenver's method. This was found to be statistically significant(p<0.000).

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.143-151
• /
• 1999

The shape of surface micro-crack is very irregular due to nonhomogeneous microstructure but is very important in respect to qualitative estimation of fatigue life. Fractal geomety can quantify the shape of surface mciro-crack. Fractal dimension is measured for surface micro-cracks with coast line and box counting method and estimates cycle ration in Al 2024-T3. The average fractal dimension $D_{favg}$ of surface micro-cracks has 3-parameter weibull distribution and location parameter is nearly constant but shape parameter decreases as cycle ration increases. The fractal dimension by coast line method is measured for individual surface micro-crack but the fractal dimension by box countin method is measured for all the surface micro-cracks under sampling area. Therefore, This paper shows fractal dimension $D_{fb}$ can predict cycle ratio $N/N_f$ more convenient than fractal dimension $D_{favg}$.