• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.8
• /
• pp.24-32
• /
• 2000

In this paper, we have designed and fabricated a new type power divider to be efficient to a size and electrical performance by folding each quarter-wavelength 70.7 Ω section into a tightly-coupled "meander-line" and inserting a slit. In this type, because of coupling, the electrical phase of quarter -wavelength line and the performance change. For this reason, with the inductive slit and the tuning of quarter-wavelength line length, we have compensated for those. The inductance value of the inserted slit is decided by its width and depth, therefore, we could improve the electrical performance through optimization of inductance. Input and output return losses of the designed power divider were -34.2 dB, -34.3 dB respectively, and isolation was -36.7 dB at 1.75 GHz. Besides, a new design approach reduced occupied substrate area by 3:1 approximately.

• ETRI Journal
• /
• v.35 no.1
• /
• pp.51-57
• /
• 2013

In this paper, a small internal antenna for a mobile handset is presented using multiband, wideband, and high-isolation multiple-input multiple-output techniques. The proposed antenna consists of three planar inverted-F antennas (PIFAs) that operate in the global system for mobile communication (GSM900), the digital communication system (DCS), the personal communication system (PCS), the universal mobile telecommunication system (UMTS), and wireless local area network (WLAN) bands with a physical size of $40mm{\times}10mm{\times}10mm$. A resonator attached to the folded PIFA creates dual resonances, achieving a wide bandwidth of approximately 460 MHz, covering the DCS, PCS, and UMTS bands; a meander shorting line is used to improve impedance matching. Additionally, a modified neutralization link is embedded between diversity antennas to enhance isolation, which results in a 6-dB improvement in the isolation and less than 0.1 in the envelope correlation coefficient evaluated from the far-field radiation patterns. Simulation and measurements demonstrate very similar results for S-parameters and radiation patterns. Peak gains show 3.73 dBi, 3.77 dBi, 3.28 dBi, 2.15 dBi, and 5.86 dBi, and antenna efficiencies show 56.15%, 72.15%, 68.59%, 52.92%, and 82.93% for GSM900, DCS, PCS, UMTS, and WLAN bands, respectively.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.279-284
• /
• 2005

We investigated the impedance matching characteristics of UHF-band RFID tag antenna and tag chip for increased reading range. A voltage multiplier designed using 0.4 $\mu$m zero-$V_T$ MOSFET showed that DC output voltage of about 2 V can be obtained using standard CMOS process. The input impedance of the voltage multiplier was examined to achieve impedance matching to the RFID tag antenna using analytical and numerical approaches. The input impedance of the voltage multiplier could be varied in a wide range by selecting the size of MOSFET and the number of multiplying stages, and thus can be impedance matched to a tag antenna in presence of other tag circuit blocks. A meander line inductively-coupled RFID tag antenna operating at UHF band also shows the feasibility of impedance matching to tile RFID tag chip.

• Journal of Navigation and Port Research
• /
• v.32 no.5
• /
• pp.363-368
• /
• 2008

This paper presents a miniaturization design technique of radio frequency identification (RFID) tag antenna operated in 910 MHz band. Miniaturization structure design for a tag antenna is performed by structure application of the folded dipole and meander line. In order to realize the maximum power transmission, imaginary part of a chip impedance and a tag antenna impedance is matched by complex conjugate number. The optimized tag antenna size is $50\;nm\;{\times}\;40\;nm\;{\times}\;1.6\;nm$ and its size is reduced about 62 % comparison with antenna size of reference [4]. The measured results of fabricated tag antenna are confirmed the reasonable agreement with prediction. The read range of the tag antenna with chip observed about 5 m.

• Progress in Superconductivity
• /
• v.4 no.2
• /
• pp.132-136
• /
• 2003

Extremely selective high temperature superconducting (HTS) band -pass filters were developed for the base transceiver station applications of Digital Cellular communication Service (DCS). The filters have a bandwidth of 25 MHz at a center frequency of 834 MHz. There are 12 resonators which have spiral-meander microstrip-line structures in order to reduce far-field radiations with a reasonable tunability. As a result, the size of filters is 5 mm $\times$ 17 mm $\times$ 41 mm. Device characteristics exhibited a low insertion loss of -0.4 dB with a -0.2 dB ripple and a return loss better than -10 dB in the pass-band at 65 K. The out-of-band signals were attenuated better than 60 dB about 3.5 MHz from the lower band edge, and 3.8 MHz from the higher band edge.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.5
• /
• pp.193-197
• /
• 2005

We investigated fault current limiting characteristics of the flux-lock type superconducting fault current limiter (SFCL), which consisted of a primary winding and several secondary windings connected in series between $high-T_C$ superconducting (HTSC) thin films. Each YBCO thin film has a 2 mm wide and 42 cm long meander line with 14 stripes of different length. The power imbalance due to the slight difference of Ie between YBCO current limiting elements causes the significant power burden on YBCO element with lower $I_C$. We confirmed from our experiments that the mutual coupling between the primary winding and secondary windings of the flux-lock type SFCL reduced the power imbalance between YBCO current limiting elements compared with the resistive type SFCL connected in series.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.4
• /
• pp.39-45
• /
• 2009

In this paper, designed and fabricated the microstrip antenna using parasitic plane. This active antenna for the use of AM/FM, DMB(Digital Multimedia Broadcasting), GPS(Global Positioning System) band in vehicle. Fabricated active antenna was compared to existing planar antenna represents more than 15% size reduction and equivalence performance compared to commercial helical antenna. And satisfy performance in DMB, GPS band. This active antenna composed of single input port and two output ports and entire size of antenna is $133{\times}31{\times}1.2mm$.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.288-294
• /
• 2004

In this paper, a ceramic antenna and diplexer are designed for dual-band handset ap plications. Basically, the antenna is designed by using the meander line configuration. The diplexer presented in this paper is composed of both low- and high-pass filters. We have designed the low- and high-pass filters with attenuation poles to improve the attenuation performances of the diplexer. The attenuation poles are located at each rejection frequency region so as to improve the shrinkage characteristic of the diplexer. In order to accomplish the volume effectiveness, the antenna and the diplexer have been designed and fabricated in a multi-layer structure. The diplexer designed with a multi-layer structure has inductors and capacitors, which are implemented by LTCC (Low Temperature Co-fired Ceramics) process technique. Design of the multi-layer antenna and diplexer has been achieved by employing the full 3-D EM simulation. The designed antenna and diplexer offer excellent return loss and broadband performances with highly isolated rejection performance.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.287-290
• /
• 2003

For microwave device applications, c-axis oriented high temperature superconducting YBa$_2$Cu$_3$O$_{7-{\delta}}$ (HTS-YBCO) epitaxial thin films on the r-cut sapphire substrate(Al$_2$O$_3$) were prepared. In order to reduce the lattice mismatch with a substrate and to enhance the crystallity of HTS thin films, CeO$_2$ buffer layer on the r-cut sapphire substrate was grown by the RF-magnetron sputtering. The YBCO films on the CeO$_2$ buffer layer were deposited using the pulsed-laser deposition (PLD) method. These HTS YBCO /CeO$_2$/Al$_2$O$_3$ multilayer thin films(30 $\times$ 30 mm$^2$) routinely exhibited a critical temperature(T$_{c}$) of 89 K from the R-T measurement. Using HTS YBCO/CeO$_2$ /Al$_2$O$_3$ multilayer thin film. We fabricated and characterized the microwave passive devices (planar type filters) with cryopack-age such as the coupled -line type low-pass filter (LPF) and the open-loop meander type bandpass filter (BPF).filter (BPF).).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05b
• /
• pp.20-23
• /
• 2003

The operational characteristics of flux-lock type high-Tc superconducting fault currentlimiters(HTSC-FCLs) was described and currents equation at each coil was derived from equivalent circuit. $YBa_{2}Cu_{3}O_{7-x}$(YBCO) thin film was used as the current limiting elements of the flux-lock type HTSC-FCL, which were fabricated by etching the YBCO thin film into 2 mm wide and 420 mm long meander line consisting of foureen stripes with different length. The 2nd peak on the current of coil 2 after a fault disappeared by current of the 3rd winding, which was installed in the flux-lock type HTSC-FCL.