• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.6
• /
• pp.843-849
• /
• 2010

This paper presents definition of symmetry of a ship section where three symmetries are proposed: material, geometric, and load symmetries. Precise terminologies of centroid, moment plane, and neutral axis plane are also defined. It is suggested that force vector equilibrium as well as force equilibrium are necessary condition to determine new position of neutral axis due to translational and rotational mobility. It is also stated that new reference datum of ENMP(elastic neutral moment plane), PNMP(fully plastic moment plane), ENAP(elastic neutral axis plane), and INAP(inelastic neutral moment plane) are required to define asymmetric section properties such as second moment of area, elastic section modulus, yield moment, fully plastic moment, and ultimate moment. Since collision-induced damage and flooding-induced biaxial bending moment produce typical asymmetry of section, the section properties are calculated for a typical VLCC. Geometry asymmetry is determined from ABS and DNV rules and two moment planes of 0/30 degs are assumed for load asymmetry. It is proved that the property reduction ratios directly calculated from second moment of area are usually larger than area reduction ratio. Reduction ratio of ultimate moment capacity shows almost linearly proportional to area reduction ratio. Mobility of elastic and inelastic neutral axis planes is visually provided.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.2
• /
• pp.135-142
• /
• 2023

Resin-bonded fixed partial denture (RBFPD)as known as Maryland bridge is is a well-known conservative method for its minimized invasion of the teeth for an anterior single tooth edentulous area. Despite of its various advantages, RBFPD was not widespread because of its high debonding rates, non-esthetic look or weak structure for material property. Currently, with the introduction of zirconia to dental material for RBFPD, Maryland bridge entered upon a new phase. Zirconia surmounts poor esthetics of metal framework, having proper strength, and overcomes ceramic's structural weakness, being sufficiently esthetic. In this case, edentulous area of maxillary left lateral incisor was restored using zirconia resin-bonded fixed partial denture. Restoration of missing tooth in anterior area was achieved using non-invasive and esthetic prosthesis, then we report this case as satisfactory results were obtained for both the operator and the patient.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.15-20
• /
• 2023

In the fine blanking process, which is a press operation known for producing parts with narrow clearances and high precision through the application of high pressure, die roll often occurs during the shearing process when the punch penetrates the material. This die roll phenomenon can significantly reduce the functional surface of the parts, leading to decreased product performance, strength, and fatigue life. In this research, we conducted an in-depth analysis of the factors influencing die roll in the curvature area of the fine blanking process and identified its root causes. Subsequently, we designed and experimentally verified a die roll reduction process specifically tailored for the door latch manufacturing process. Our findings indicate that die roll tends to increase as the curvature radius decreases, primarily due to the heightened bending moment resulting from reduced shape width-length. Additionally, die roll is triggered by the absorption of initial punch energy by scrap material during the early shearing phase, resulting in lower speed compared to the product area. To mitigate the occurrence of die roll, we strategically selected the Shaving process and carefully determined the shaving direction and clearance area length. Our experiments demonstrated a promising trend of up to 75% reduction in die roll when applying the Shaving process in the opposite direction of pre-cutting, with the minimum die roll observed at a clearance area length of 0.2 mm. Furthermore, we successfully implemented this approach in the production of door latch products, confirming a significant reduction in die roll. This research contributes valuable insights and practical solutions for addressing die roll issues in fine blanking processes.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.3 s.17
• /
• pp.91-99
• /
• 2005

It is required to study systematical on the concrete quality management to extend structure life because rebuilding effect is reducing under present condition of large sized and high stories structure. Concrete, which shows its intensity by hydrating action and a big change in quality according to hot weather and temperature, produces a lot of qualify problem under hot and cold weather Because of each specification and construction plan which does not have basic standard on site, concrete's quality is irregular and makes some defect. As a result, Daegu is turned out to be the longest area after investigating application period and days focused on 8 cities weather information about relationship between hot weather circumstance and construction environment. Therefore, we first surveyed the concrete material in the region and found out the problem of quality nanagement. Then figure out the way of solution. Moreover, we integrated concrete material quality management, which is applied differently to each site, to have equal quality and to reduce defect from construction site. And then, based on various test of construction condition and analysis of quality management item, we suggest effective concrete quality management to make concrete material construction standard guide and plan under hot weather.

• Journal of the Korean Applied Science and Technology
• /
• v.23 no.2
• /
• pp.147-152
• /
• 2006

The accidents occurred by unstable material which is easily exploded or burnt up were caused by heat and collision under the condition of relatively low temperature without oxygen, have been reported frequently. However, the amount of the unstable material is getting higher by development of fine ceramic research area even though its dangerous characteristic is disregarded. This research studied a heat stability and measured boiling point of various carpet material. Carpet has been used in home as well as general indoor usage. Now a day, carpet material which is hardly burnt has been on commercial, but its detailed unstable conditions is not mentioned. This research reports the measurement of the initial temperature of generation heat and heat-radiation change on differential scanning calorimeter (DSC). The DSC data of nylon bulked continuous filament (N-BCF) yam 100%, nylon (NY), poly propylene (PP), and a new material named polytrimethylene terephthalate (PTT) are studied and researched about the effect of them using TGA, furnace, and direct-burning experiment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.29-32
• /
• 1998

A new treatment of LiV$_3$O$_{8}$ has beer proposed for improving its electrochemical behavior as a cathode material secondary lithium batteries. Early in its development, the preparation method of LiV$_3$O$_{8}$ strongly influenced its electrochemical properties, such as discharge capacity, rate capability and cycling efficiency. In the present experiment, a new synthesis route has been applied to obtain LiV$_3$O$_{8}$ . Instead of the conventional high temperature technique leading to the crystalline form, a solution technique producing the amorphous form has been used. This material, after dehydration, shows an electrochemical performance exceeding that of the crystalline one. These measurements showed that the ultrasonic treatment process of crystalline LiV$_3$O$_{8}$ causes a decrease in crystallinity and considerable increases in specific surface area and interlayer spacing. So the ultrasonic method provides a convenient means for improving the electrochemical behavior of LiV$_3$O$_{8}$ as a cathode material for secondary lithium batteries.batteries.

• Journal of the Korean Chemical Society
• /
• v.38 no.10
• /
• pp.726-733
• /
• 1994

Supercritical fluid extraction (SFE) followed by gas chromatographic separation and mass spectrometric (MS) detection were used in rapid analysis of polycyclic aromatic hydrocarbons (PAH's) in air particulate material extracted for 30 min with 10 ml of supercritical $N_2O$ without another sample preparation step. Two samples, urban dust in Seoul area and a certified air particulate reference material 1649 supplied by the NBS (National Bureau of Standards), were processed for the purpose of evaluating extraction and analysis methods. As a result, the quantitative recovery of PAH's in the SFE method was relatively lower than conventional organic solvent extraction methods, but reproducibility was resonable, and analysis time was reduced remarkably. The method has proved to be suitable for monitoring of PAH's in air particulate material.

• Journal of Hydrogen and New Energy
• /
• v.8 no.1
• /
• pp.11-21
• /
• 1997

$ZrV_{0.7}Mn_{0.5}Ni_{1.2}$ alloy is attractive for anode material in Ni/MH secondary battery because of its large hydrogen storage capacity in gas-solid reaction and long cycling durability in KOH electrolyte. In this work, in order to further improve the discharge performance of this alloy electrode, the alloy was annealed by optimal condition which is for 12 hours at $1000^{\circ}C$. The alloy annealed under optimal condition had higher rate capability and discharge capacity than as-cast one. The microstructure of the as-cast and annealed alloy was investigated by scanning electron microscopy and energy dispersive spectroscopy. Ni content in the matrix was increased, being this homogenized after annealing. Additionally, The measurement of the surface area by B.E.T. analysis showed that there was little difference as-cast and annealed alloy. Therefore, improvement in the rate capability of the annealed alloy is due to increase of Ni content in the matrix.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.18 no.3
• /
• pp.368-386
• /
• 1994

The primary purpose of this study was to identify the diversity and embellishment of American Indian clothing and relationship between culture and clothing in American Indian Culture Areas. After the introduction of European material culture, change in American Indian clothing was conducted. The result of the Study as follows: 1. The most influential factors affecting the diversity of American Indian clothing were environmental factors. Climates and geographical features, Raw material were reflected in clothing style and clothing material in each culture Area. 2. Economic situation and life style were shown to be influential to clothing development. The best known instance of this was greatly elaborated clothing and personal adornment of the Plains who had higher stand of life and nomadic life style. 3. Religious concepts were important factors influencing American Indian clothing. Indian tribes had different ritual performance they used particular motifs in clothing. Clothing, such as "ghost shirt", Apache medicine shirt and Pueblo ceremonial clothing, served hidden pur- poses. 4. Techenology was another factor identified in this study as influencing American Indian clothing. Especially, weaving skills of Southwest played a great role in textile development. Pueblo "manta" and Navaho "bil" were famous for Indian costume. 5. European material culture allowed great change of traditional native Indian clothing. American Indian had new material, new styles, new concept of clothing. 6. American Indian, although Indian applicated European trade goods, was actually quite conservative in retaining traditional designs and modes of decoration. Asthetics and traction of American Indian were reflected in American Indian clothing.d in American Indian clothing.

• Korean Institute of Interior Design Journal
• /
• v.15 no.6 s.59
• /
• pp.60-67
• /
• 2006

In modem days when architectural materials have grave impacts on overall design expression, materials for architecture, especially finishing materials have become the most essential elements for the design expression, as architectural space and form have been. When it comes to the architectural materials, they can be conceived by visual and tactile sensory system and perceptional system which based on memory and experience. This study confirms how materials bring into effect on architecture in the sense of its design. The main subject of this analysis is expression method of architectural finishing materials. Also, this study finds out the relationship between finishing materials and the images of materials by analyzing the effect factor of architectural material expression with the perspectives of materials, formal and environments and by examining roles of the architectural materials in design. The material factor, in the expression of materiality, is how to make tectonic space and to vary the surface of building as finishing material design. The formal factor is related to set up the new direction in the architectural form and to create the dynamic and informal space. And the social and cultural environment as the effect factor gives new situation and context to architectural material expression. This principle enables us to use architectural materials as one of the important elements which express the whole characteristics of the area.