• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.3
• /
• pp.12-21
• /
• 2022

Directed energy deposition (DED) was adopted as a metal additive manufacturing method to develop a mold for the hot stamping process. The test piece was machined from Heatvar laminate material, and results were obtained through microstructure and defect observations, as well as hardness, tensile strength, and joint strength tests. 1) Spherical pores and irregular-shaped cavities were observed as lamination defects, and columnar dendrites formed in the structure, which tended to become coarse upon heat treatment. 2) The hardness of the heat-treated material (480HV) was slightly lower than that of the non-heat-treated material (500HV). 3) In the tensile test, the maximum tensile stress and strain of the heat-treated material were 1392 MPa and 15%, respectively, which were slightly higher than the values of 1381 MPa and 13%, respectively, for the non-heat-treated material. 4) In the case of the early final fracture in the tensile test, in most cases, pores or irregularly shaped cavities were observed at the fracture surface or near the surface. 5) In the joint strength test, most of the specimens finally fractured in the laminated metal area, and the fracture surface was intragranular. In addition, dimples formed over the entire area on the fracture surface of the fractured specimen after sufficient elongation.

• Korean Institute of Interior Design Journal
• /
• v.20 no.4
• /
• pp.201-210
• /
• 2011

This study is on the space planning of accommodation area in accommodation barge, which is a kind of offshore plant supply vessel providing workers with exclusive accommodation facilities. Firstly, the space layout of accommodation area is analyzed using the general arrangement drawings of 10 actually-built accommodation barges currently in use. Secondary, the design guides and standards for living quarters of offshore plants issued from overseas classification societies such as ABS, NORSOK etc. are analyzed and based on the analysis design guidelines for accommodation area of accommodation barge are newly suggested. Thirdly, a model of accommodation area in accommodation barge is set up and space arrangements and movement lines for each deck of the accommodation area of the model are planned. Fourthly, cabins, dinning room and galley, recreation spaces, and sanitary spaces of the accommodation area of the model are planned. The results of this study may be summarized as follows. An accommodation barge has 'barge deck' for small scale work and material storage, and 'accommodation area' for the living and resting of workers. The accommodation area is made of workers accommodation sector, service sector, crew sector and business sector. The interior design guidelines for accommodation area of accommodation barge should be made soon by Korea Register of Shipping.

• Journal of Korean Society of Rural Planning
• /
• v.13 no.3
• /
• pp.83-90
• /
• 2007

The purpose of main entrance was to protect the house with the wall and working for the house-gate where people come in and go out. On the other hand, the type of main entrance is changed variously depended on the materials for house and method of construction. Eleven villages in the Chungyang-Gun where the environment of rural villages is well maintained was chosen and researched to make data. These data of visual landscape elements were analysed by using the SPSS 12.0 for Windows. Relations of the visual component elements were analysed by the analysis for frequency and analysis for crosstab. From the above research we could conclude below results. Through review of the pre-researching and researching literatures, 11 types of visual component elements were selected such as the types of the gate, the looking through degree of the gate, the material of the gate, the color of the gate, the plan of the house, the material of the roof, a material of the wall, a color of the wall, the form of the penetration, the area to put, the area of a site, the year of the constructing a building. For the types of the gate, the gate from without the roof has been the most popular since it appeared 41.5%. For the looking through degree of the gate, a complete blockade form has been the most popular since it appeared 63.2%. For the material of the gate, the iron plate has been the most popular since it appeared 32.1%. For the color of the gate, color has been the most popular since it appeared 68.4%. For the plan of the house, 'ㄷ' form has beneath most popular since it appeared 38.3%. For the material of the roof. The Zinc has been the most popular since it appeared 51.9%. For a material of the wall, A cement mortar has been the most popular since it appeared 47.7%. For a color of the wall, Without tile color has hem the most popular since it appeared 67.0%. For the form of the penetration. The plain form has been the most popular since it appeared 54.0%. For tile area of a site, $100m^2{\sim}200m^2$ has been the most popular since it appeared 39.0%. The results of this study can provide to use of indicates four rural-housing reform. From now on, the results look forward to offering the meaning directions for the improvement of rural house gates.

• International Journal of Highway Engineering
• /
• v.6 no.1 s.19
• /
• pp.47-56
• /
• 2004

To determine the pure bond strength between substrate and its overlayed concrete material, a direct pull-off test method was introduced by using a bi-material cylinder with which a penny-shaped crack was mountained at its interface. First, to evaluate the stress magnification or concentration at the interface, the energy release rates of a penny-shaped interface crack in remote tension loading on a bi-material cylinder were determined in terms of different modulus ratios and undonded area ratios(crack ratios) using a commercial finite element program. Then the energy release rates were calibrated as non-dimensional values in consideration of structural dimensions and applied forces. And to evaluate whether this new pull-off test method gives sound test results, three different sizes of unbended area ratios were incorporated along their interface in bi-material cylinders(sulphur polymer concrete + old concrete). Test results showed that all specimens were broken off at their interfaces as intended. Also the FEM analyses and test results indicated that a bi-material specimen with unbended area ratio of 0.4$\sim$0.6 is suitable for best accurate testing.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.10
• /
• pp.49-57
• /
• 2013

Recently, recycling of the industrial by-products has been an important issue of the Yeosu bay, where large industrial complex is located. Major industrial by-products which are produced from Yeosu industrial complex area are phosphogypsum and flyash, which are about 82% and 10% of the 1.6 million tons industrial by-products. Moreover since the Yeosu industrial complex is located at seaside, phosphogypsum has been pointed as cause of serious environmental contaminant from the regional society. Therefore recycling study can't be delayed anymore. In this paper, artificial aggregate was manufactured by non-sintering process from industrial byproducts - e.g., phosphogypsum and slag - as a geotechnical drainage material. To show the feasibility of the artificial aggregate as a geotechnical drainage material, geotechnical experiments including particle size analysis, permeability test, and large scale direct shear test were carried out. Test results show that the permeability of the artificial aggregates range from $6.94{\times}10^{-1}cm/sec$ to $8.86{\times}10^{-1}cm/sec$, which is much larger value than those are required for the drainage material from the construction specification in Korea, and the friction angle of the artificial aggregate is as large as that of sand in water immersion conditions. From the test results, it was concluded that artificial aggregate made from industrial by-products can be used successfully as a geotechnical drainage material.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.132.2-132.2
• /
• 2010

Mesoporous tinoxide ($SnO_2$) as anode materials for Li-ion battery were prepared by hydrothermal method and templating method using SBA-15 as template. And electrochemical properties of $SnO_2$ electrode were investigated with cyclic voltammogram (CV). The morphology and structures of $SnO_2$ were characterized by transmission electron microscopy (TEM) and X-ray diffractometer (XRD), respectively. The specific surface area was defined by $N_2$ adsorption with BET(Brunauer-Emmett-Teller) method. As a result, the surface area of mesoporous $SnO_2$ which was made from templating method is higher than the case of using hydrothermal method. In addition, in anodic performance, mesoporous $SnO_2$ which is prepared by templating method showed higher charge-discharge capasity compared to hydrothermal method and exhibited excellent stability over the entire cycle number. It was indicated that electrochemical performances of mesoporous $SnO_2$mainly affected to the structural features, such as specific surface area and porosity.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.95-107
• /
• 2000

The primary purpose of dredging work is to maintain navigational readiness and to increase environmental amenity, so that the dredging project which is composed of excavating, removing, transporting, storing and disposing dredged material must be carefully managed to insure that dredging works are completed in a cost-effective and environmentally safe manner. The most important point in dumping operations is an estimating and reducing the impacts of discharges at the dumping area. One of the most effective method for the reduction of ecological impacts at dumping area is using the schematic process composed of the sophisticated plan, precise work and predicting/reducing the impacts based on the numerical model and field observation. In this study, the numerical model is used to predict the near-field spatial fate and begavior of effluent discharged from Confined Dumping Facility(CDF) located near coastal area. To to this purpose, reappearing of tidal current was preceded. The model is then applied to Mokpo harbor, where capital dredging and maintenance dredging are conducted simultaneously and the CDF is under construction;. In the series of model case study, we found that the near-field behavior of effluent discharged from CDF was governed by the receiving water condition, outfall geometry, characteristics of efflent and CDF operating conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.2
• /
• pp.153-158
• /
• 2012

We use UV(ultraviolet)-$O_3$ treatment to increase the surface area and porosity of $TiO_2$ films in dye-sensitized solar cells (DSSCs). After the UV-$O_3$ treatment, surface area and porosity of the $TiO_2$ films were increased, the increased porosity lead to amount of dye loading and solar conversion efficiency was improved. Field emission scanning electron microscopy images clearly showed that the nanocrystalline porosity of films were increased by UV-$O_3$ treatment. The Brunauer, Emmett, and Teller surface area of the $TiO_2$ films were increased from $0.71cm^2/g$ to $1.31cm^2/g$ by using UV-$O_3$ treatment for 20 min. Also, UV-$O_3$ treatment of $TiO_2$ films significantly enhanced their solar conversion efficiency. The efficiency of the films without treatment was 4.9%, and was increased to 5.6% by UV-$O_3$ treatment for 20 min. Therefore the process enhanced the solar conversion efficiency of DSSCs, and can be used to develop high sensitivity DSSCs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.1
• /
• pp.1-5
• /
• 2001

STI(shallow trench isolation)-CMP(chemical mechanical polishing) process have been substituted for LOCOS(local oxidation of silicon) process to obtain global planarization in the below sub-0.5㎛ technology. However TI-CMP process, especially TI-CMP with RIE(reactive ion etching) etch back process, has some kinds of defect like nitride residue, torn oxide defect, etc. In this paper, we studied how to reduced torn oxide defects after STI-CMP with RIE etch back processed. Although torn oxide defects which can occur on trench area is not deep and not severe, torn oxide defects on moat area is not deep and not severe, torn oxide defects on moat area is sometimes very deep and makes the yield loss. Thus, we did test on pattern wafers which go through trench process, APECVD process, and RIE etch back process by using an IPEC 472 polisher, IC1000/SUVA4 PAD and KOH base slurry to reduce the number of torn defects and to study what is the origin of torn oxide defects.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.111-115
• /
• 2004

In this paper, evaluation of physical properties about dielectric relaxation phenomena by the detection of the surface pressures and displacements current on the monolayer films of phospolipid monomolecular DLPC, DMPC using pressure stimulus. As a result, the changed surface pressure, displacement current and the transition forms of dipole moment of phospolipid monomolecular in area per molecular by pressure stimulus were conformed well. It was known that the monolayers by linear relationship for decision of dielectric relaxation time between compressure speed $\alpha$ and molecule area $A_m$ By according to the linear relationship relation get that frictional constant $\xi$, DLPC was $1.89{\times}10^{-19}$[Js] and DMPC was $0.722{\times}10^{-19}$[Js]. It is found that the phospolipid monolayer of dielectric relaxation takes a little time and depend on the molecular area.