• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.8
• /
• pp.730-738
• /
• 2001

This work discusses the pressure droop, heat and mass transfer of the finned-tube heat exchangers having 7 mm tubes and offset strips in dehumidifying applications. It focuses on the fin material saving and the reduction of pressure drop. The experiment was conducted using three times scaled-up models to simulate the performance of the prototype. Eight kinds of fins having different strips and S shape edges were tested. the area density of the strip was a major factor and its shape and the location were secondary factors on the pressure drop, the heat and mass transfer. The reduced-area fin can almost equal the non-reduced fin in the aspect of heat and mass transfer. The strip fins proposed in the present work can considerably reduce both the pressure drop and the fin material for similar thermal load.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.12-17
• /
• 2016

Recently, lightweight material is attracting attention as a solution to the problem of fuel efficiency and increasing the need for development. CFRP has been attracting attention as lightweight materials for automobile because it has a high specific stiffness and specific strength compared to steel material. CFRP have a wide range of mechanical properties depending on the laminate condition. In this paper, study on the forming analysis of double-dome model was performed considering CFRP prepreg laminate condition and coefficient of friction. After forming analysis, the result has compared with wrinkling area and vertical strain of fiber to the laminated condition. And then compared with inflow of blank to the laminate condition. Through this paper, we propose the forming analysis methods of CFRP material.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.1
• /
• pp.29-35
• /
• 2023

Herein we investigated the effect of the conductive agent on the electrochemical performance of the SiOx anode. SiOx anodes have a relatively low volume expansion (~160%) compared to Pure-silicon, but have a problem in that they have a poor electrical conductivity characteristic. In this study, physical and electrochemical measurements were performed using two 0-dimensional amorphous carbon conductive agents with different crystallinity and surface area. The crystal structure of the conductive agents and the local graphitization degree were analyzed through XRD and Raman, and the surface area of the particles was observed through BET. In addition, the electrical performance according to the graphitization degree of the conductive agents was confirmed through a 4-point probe. As a result of the electrochemical cycle and rate performance, it was confirmed that the performance of SiOx using a conductive agent having a low graphitization degree and a high surface area was improved. The results in this study suggest that the graphitization degree and surface area of the amorphous carbon conductive agent may play an important role in the SiOx electrode.

• Geomechanics and Engineering
• /
• v.15 no.4
• /
• pp.927-935
• /
• 2018

The mechanical behavior of the brittle material samples containing the internal and edge cracks are studied under direct shear tests. It is tried to investigate the effects of stress interactions and stress intensity factors at the tips of the pre-existing cracks on the failure mechanism of the bridge areas within these cracks. The direct shear tests are carried out on more than 30 various modeled samples each containing the internal cracks (S models) and edge cracks (E models). The visual inspection and a low power microscope are used to monitor the failure mechanisms of the tested samples. The cracks initiation, propagation and coalescences are being visualized in each test and the detected failure surfaces are used to study and measure the characteristics of each surface. These investigations show that as the ratio of the crack area to the total shear surface increases the shear failure mode changes to that of the tensile. When the bridge areas are fixed, the bridge areas in between the edge cracks have less strength than those of internal cracks. However, the results of this study show that for the case of internal cracks as the bridge area is increased, the strength of the material within the bridge area is decreased. It has been shown that the failure mechanism and fracture pattern of the samples depend on the bridge areas because as the bridge area decreases the interactions between the crack tip stress fields increases.

• Economic and Environmental Geology
• /
• v.9 no.1
• /
• pp.45-73
• /
• 1976

This study has been made for the enlargement of a previous work of 1964 which was carried out by an author of this work emphasizing the stratigraphy, micropaleontology, depositional environment, and structural tectonics of the studied area. The stratigraphic sequences of the area are groupped into four units: (1) basement of Pre-Cretaceous, (2) lower sediments of Late Cretaceous, (3) upper sediments of Late Cretaceous and (4) igneous rocks of Late Cretaceous and Tertiary (?). The oldest rocks consisting of schists and gneisses of Pre-Cambrian and schistose granite' of Jurassic age are exposed at the base of this area on which the thick Cretaceous sediments were deposited. These old rocks are unconformably overlain by the lower sedimens of Late Cretaceous composed of three members, an alternation of black shale and tuffaceous sediments, fine tuff and rhyollite flow in ascending order. The oily material was found from the black shales of the alternation m"ember as semi-solid greaselike material, oily order and microscopic granular spherical material and oily stain. The lower sediments are also overlain, in low-angleunconfromity, by the 'upper sediments having three members, an alternation of volcanic conglomerate and andesitic tuff, rhyollitic tuff and andesite flow in the same order. The igneous suit of diabase, diorites, biotite granite, porphyritic granite and porphyries of the latest Cretaceous and small exposure of pitchstone of Tertiary (?) intruded into the pre-existed rocks above mentioned. Considerable amount of ostra- coda microfossils have been chemically extracted from the black shales of the lower sediments and the identification of the fossils suggests that the depositional environment of the sediments were under fresh or brackish water condition. The distribution of the geology and its tectonic data also suggest a combination of dome and basin structures in the area of San-i peninsula and Jin-do as shown in fig. 8. Between these two units an anticlinal structure was constructed. As a result of this study, a seismic survey in a district between U-su-yong and north coast of Jin-do is recommended to determine the underground features.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.243-244
• /
• 2009

The $TiO_2$ nanofiber doped $TiO_2$ electrode area applied to dye-sensitized solar cells(DSSCs). The mixtures of $TiO_2$ nanofiber to $TiO_2$ photoelectrode has larger surface area than $TiO_2$ photoelectrode. In this research added 2.5, 5 and 10wt% $TiO_2$ nanofibers and the optimum condition of 5 wt% $TiO_2$ nanofiber's high surface area contributing the improvement of short-circuit photocurrent. The open-circuit voltage was 0.7V and solar energy conversion efficiency was 5.4%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.628-631
• /
• 2001

Current lead is one of the first proposed devices for the application of High Temperature-Superconductor(HTSC). The current lead provides high current for electrical machine using superconductor from room temperature. Its characteristics that is zero resistance and low heat transfer rate under critical temperature lead to research for the replacement of existing current lead with HTSC. In this paper, we investigated the temperature distributions of stacking type and rod type current lead with each cross-section area and length using Nastran program and compared each temperature distribution. It is obtained from this paper that stacking type current lead has flat temperature gradient and than rod type one and more stable operation as current lead is closely related with its cross-section area and length.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.25-28
• /
• 2001

Recently, STI(Shallow Trench Isolation) process has attracted attention for high density of semiconductor device as a essential isolation technology. Without applying the conventional complex reverse moat process, CMP(Chemical Mechanical Polishing) has established the Process simplification. However, STI-CMP process have various defects such as nitride residue, torn oxide defect, damage of silicon active region, etc. To solve this problem, in this paper, we discussed to determine the control limit of process, which can entirely remove oxide on nitride from the moat area of high density as reducing the damage of moat area and minimizing dishing effect in the large field area. We, also, evaluated the reliability and reproducibility of STI-CMP process through the optimal process conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.853-856
• /
• 2002

Present. direct method x-ray conversion detector is studied by abroad medical instrument and country with amorphous Selenium. And we search the method for large area x-ray detector. Amorphous-Selenium based photoreceptor is widely used on the X-ray conversion materials. But amorphous-selenium based x-ray conversion detector is broken by high voltage and leakage defect point. In this paper, We investigated top-electrode distance rate to improve defect point and high voltage broken. The result to appoint to made large area x-ray conversion detector with base data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.183-186
• /
• 2004

Unipoled piezoelectric transformers were designed with different input and output area ratios. The voltage step-up ratio increased proportionally with increasing the input area. The piezoelectric transformers operated in each transformer's resonance vibration mode. In this paper, ANSYS(FEM program) was used for analysing piezoelectric transformers. We compared with analysis and experimental results. The voltage step-up ratio showed maximum value in output area of small size. Output characteristics of piezoelectric transformers with various size were simulated. The result of analysis showed 2~7 times higher voltage step-up ratio than a experiment result.