• 제목/요약/키워드: master curves

검색결과 47건 처리시간 0.022초

Warm Tensile Deformation Behavior and Constitutive Equation of Supersaturated Solid-Solutionized Al-9Mg Extruded Alloy

  • Seung Y. Yang;Bong H. Kim;Da B. Lee;Kweon H. Choi;Nam S. Kim;Seong H. Ha;Young O. Yoon;Hyun K. Lim;Shae Kim;Young J. Kim
    • Archives of Metallurgy and Materials
    • /
    • 제66권4호
    • /
    • pp.1013-1018
    • /
    • 2021
  • In this paper, as a purpose to apply the supersaturated solid-solutionized Al-9Mg alloy to the structural sheet parts of automotive, tensile tests were conducted under the various conditions and a constitutive equation was derived from the tensile test results. Al-9Mg alloy was produced using a special Mg master alloy containing Al2Ca during the casting process and extruded into the sheet. In order to study the deformation behavior of Al-9Mg alloy in warm temperature forming environments, tensile tests were conducted under the temperature of 373 K-573 K and the strain rate of 0.001/s~0.1/s. In addition, by using the raw data obtained from tensile tests, a constitutive equation of the Al-9Mg alloy was derived for predicting the optimized condition of the hot stamping process. Al-9Mg alloy showed uncommon deformation behavior at the 373 K and 473 K temperature conditions. The calculated curves from the constitutive equation well-matched with the measured curves from the experiments particularly under the low temperature and high strain rate conditions.

사각형강목의 끝자루를 이용한 트롤어구의 어획선택성 연구 ( 2 ) - 다이아몬드형강목과 사각형강목의 선택성비교 - ( Studies on the Selectivity of the Trawl Net With the Square Mesh Cod-End ( 2 ) - Comparison of Diamond and Square Mesh Cod-End - )

  • 김삼곤;이주희;박정식
    • 수산해양기술연구
    • /
    • 제30권3호
    • /
    • pp.172-181
    • /
    • 1994
  • The mesh selectivity of diamond and suare mesh cod-ends at the Southern Korean Sea and the East China Sea were compared for Pampus argenteus, Trachurus japonicus, Trichiurus lepturus. Selection trials were carried out using diamond and square mesh cod-end by trouser type cod-end with cover net. of which the mesh cod-end has four types : A(51.2mm), B(70.2mm), C(77.6mm), D(88.0mm). Selection curves and selection parameters were calculated using a logistic model. The results obained are summarized as follows : 1. Harvest fish : In B. C and D type selection range and fifty percent selection length of the square mesh were about 21mm, 11mm : 12mm, 18mm and 34mm, 5mm higher than those of the diamond mesh, respectively. Selection factor of master curve for the diamond mesh was 1.54 and for the square mesh was 1.68. The optimum mesh size for the diamond mesh was 97.4mm and for the square mesh was 89.3mm, the difference was 8.1mm. 2. Horse mackerel : In A type, selection range was nearly the same for the diamond and the square mesh, but fifty percent selection length of the square mesh was 43mm higher than the diamond mesh. In B. C and D type, selection range and fifty percent selection length of the square mesh were about 6mm, 3mm : 24mm, 21mm and 11mm, 42mm higher than those of the diamond mesh, respectively. Selection factor of master curve for the diamond mesh was 2.37, for the square mesh was 2.77. The optimum mesh size for the diamond mesh was 78.1mm and for the square mesh was 66.8mm, the difference was 11.3mm. 3. Hair tail : In A, B and C type, selection range of the square mesh was about 34mm, 8mm, 60mm higher than those of the diamond mesh. Fifty percent selection length for the diamond mesh was about 5mm, 7mm, 8mm higher than that of the square mesh. Selection factor of master curve for the diamond mesh was 3.11, for the square mesh was 3.48. The optimum mesh size for the diamond mesh was 64.3mm and for the square mesh was 57.5mm, the difference was 6.8mm.

  • PDF

사각형강목의 끝자루를 이용한 트롤어구의 어획선택성 연구 ( I ) - 사각형강목의 어획선택성 - ( Studies on the Selectivity of the Trawl Net With the Square Mesh Cod-End ( 1 ) - Selectivity of the Square Mesh Cod-End - )

  • 이주희;김삼곤;김진건
    • 수산해양기술연구
    • /
    • 제30권3호
    • /
    • pp.161-171
    • /
    • 1994
  • Mesh selection analysis for the trawl net were carried out at the Southern Korean Sea and the East China Sea during the 1992-1994 years by the training ship Seabada of the National Fisheries University of Pusan, using A type (51.2mm), B type (70.2mm), C type (77.6mm), D type (88.0mm) square mesh cod-ends. The fishing trials were made using bottom trawl of the trouser type cod-end with cover net. Selection curves and selection parameters were calculated by a logistic model for Sphyraena pinguis, Pampus argenteus, Trachurus japonicus, Pagrus major, Callanthias japonicus, Trichiurus lepturus. The results obtained are summarized as follows: 1. Red barracuda : Selection range and fifty percent selection length in the A type was 115.8mm, 292.8mm, respectively. 2. Harvest fish : Each selection range and fifty percent selection length in the B. C. and D type was 37.7mm, 113.8mm : 40.1mm, 131.7mm and 64.8mm, 148.6mm, respectively. Selection parameters of master curve were : slope, 3.81 : intercept, -6.4. Optimum mesh size was 89.3mm. 3. Horse mackerel : Each selection range and fifty percent selection length in the A, B, C and D type was 43.0mm, 148.3mm : 60.7mm, 183.2mm, 214.5mm and 91.4mm, 254.9mm, respectively. Selection parameters of master curve were : slope 2.30 : intercept, -6.4. Optimum mesh size was 66.8mm. 4. Red seabrem : Selection range and fifty percent selection length in the D type was 42.7mm, 203.4mm, respectively. 5. Yellowsail red bass : Selection range and fifty percent selection length in the A type was 84.0mm, 110.6mm, respectively. 6. Hair tail : Each selection range and fifty percent selection length in the A, B and C type was 59.7mm, 176.0mm : 100.9mm, 250.7mm and 178.6mm, 307.0mm, respectively. Selection parameters of master curve were : slope, 1.54 : intercept, -5.4. Optimum mesh size was 57.5mm.

  • PDF

벌크 비정질 Zr-Ti-Cu-Ni-Be 합금의 고온 소성 변형 특성 (High Temperature Plastic Deformation Behaviors of the Bulk Metallic Glass Zr-Ti-Cu-Ni-Be Alloy)

  • 이광석;하태권;안상호;장영원
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2001년도 추계학술대회 논문집
    • /
    • pp.272-276
    • /
    • 2001
  • Multicomponent $Zr_{41.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ bulk matallic glass alloy shows good bulk glass forming ability due to its high resistance to crystallization in the undercooled liquid state.1) In this study, DSC and X-ray diffractometry have been performed to confirm the amorphous structure of the master $Zr_{41.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ alloy. To investigate the mechanical properties and deformation behaviors of the bulk metallic $Zr_{41.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ alloy, a series of compression tests has been carried out at the temperatures ranging from $351^{\circ}C$ to $461^{\circ}C$ and at the various initial strain rates from $2{\times}10^{-4}s^{-1}\;to\;2{\times}10^{-2}s^{-1}$. There are two types of nominal stress-strain curves. The one shows linear stress-strain relationship meaning fracture at maximum stress, the other shows plastic deformation including steady-state flow. Also DSC analysis for the compressed specimens has been performed to investigate the change of thermal stability and crystallization behavior for the various test conditions.

  • PDF

MEAN LOAD EFFECT ON FATIGUE OF WELDED JOINTS USING STRUCTURAL STRESS AND FRACTURE MECHANICS APPROACH

  • Kim, Jong-Sung;Kim, Cheol;Jin, Tae-Eun;Dong, P.
    • Nuclear Engineering and Technology
    • /
    • 제38권3호
    • /
    • pp.277-284
    • /
    • 2006
  • In order to ensure the structural integrity of nuclear welded structures during design life, the fatigue life has to be evaluated by fatigue analysis procedures presented in technical codes such as ASME B&PV Code Section III. However, existing fatigue analysis procedures do not explicitly consider the presence of welded joints. A new fatigue analysis procedure based on a structural stress/fracture mechanics approach has been recently developed in order to reduce conservatism by erasing uncertainty in the analysis procedure. A recent review of fatigue crack growth data under various mean loading conditions using the structural stress/fracture mechanics approach, does not consider the mean loading effect, revealed some significant discrepancies in fatigue crack growth curves according to the mean loading conditions. In this paper, we propose the use of the stress intensity factor range ${\Delta}K$ characterized with loading ratio R effects in terms of the structural stress. We demonstrate the effectiveness in characterizing fatigue crack growth and S-N behavior using the well-known data. It was identified that the S-N data under high mean loading could be consolidated in a master S-N curve for welded joints.

벌크 비정질 Zr-Ti-Cu-Ni-Be 합금의 고온 압축 변형 특성 (High Temperature Compressive Deformation Behavior of the Bulk Metallic Glass Zr-Ti-Cu-Ni-Be Alloy)

  • 이광석;하태권;안상호;장영원
    • 소성∙가공
    • /
    • 제10권7호
    • /
    • pp.565-572
    • /
    • 2001
  • It is well known that a multicomponent $Zr_{4l.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ bulk metallic glass alloy shows good bulk glass forming ability due to its high resistance to crystallization in the undercooled liquid state. DSC and XRD have been performed to confirm the amorphous structure of the master alloy. To investigate the mechanical properties and deformation behavior of the bulk metallic $Zr_{4l.2}Ti_{13.8}Cu_{12.5}Ni_{10}Be_{22.5}$ alloy, a series of compression tests has been carried out at the temperatures ranging from $351^{\circ}C$ to $461^{\circ}C$at the various initial strain rates from $2{\times}10^4s^1$ to $2{\times}10^2s^1$. Three types of nominal stress-strain curves have been identified such as linear stress-strain relationship meaning fracture at maximum stress, plastic deformation including stress overshoot and steady-state flow, plastic deformation without stress overshoot depending on the strain rate and test temperature. Also DSC analysis for the compressed specimens was carried out to investigate the change of structure, thermal stability and crystallization behavior for the various test conditions.

  • PDF

통발에 대한 물렁가시붉은새우 (Pandalopsis japonica)의 망목 선택성 (Size selectivity of a dome-shaped pot for Morotoge shrimp Pandalopsis japonica in the eastern coastal waters of Korea)

  • 박창두;조삼광;배재현;김현영;차봉진
    • 수산해양기술연구
    • /
    • 제51권3호
    • /
    • pp.396-404
    • /
    • 2015
  • Morotoge shrimp Pandalopsis japonica is caught by pot and others in the eastern coastal waters of Korea. Comparative fishing experiments were carried out in the eastern coast of Korea, using the dome-shaped pots with different five mesh sizes (17.1, 24.8, 35.3, 39.8, and 48.3 mm) in order to estimate the mesh selectivity of the pot for the morotoge shrimp, Pandalopsis japonica. The SELECT (Share Each Length's Catch Total) analysis method was applied to the catch data. The master selection curve of the pot for the shrimp was estimated to be s(R) = exp(15.770R-10.573)/[1+exp(15.770R-10.753)], where R is the ratio of carapace length to mesh size. From the selection curves, the carapace lengths of 50% retention were 11.6, 17.0, 23.9, and 34.1 mm for 17, 25, 35, and 50 mm mesh-size pot, respectively. It means that the pots of larger mesh size allow more shrimp of small size to escape.

유리섬유 보강재를 이용한 재활용 아스팔트 혼합물의 물리적 특성에 관한 연구 (A Study on the Physical Properties of Recycled Asphalt Mixtures Using Glass Fiber Reinforcement)

  • 박기수;유평준
    • 한국도로학회논문집
    • /
    • 제20권4호
    • /
    • pp.27-34
    • /
    • 2018
  • PURPOSES : The objective of this study is to evaluate the physical properties of recycled asphalt mixtures reinforced with glass fiber. METHODS : Firstly, mixing design was conducted on recycled asphalt mixture for use of 50% recycled aggregate. Various laboratory tests were performed on four types of recycled asphalt mixtures with different glass fiber content to evaluate the physical properties. The laboratory tests include indirect tensile strength test, dynamic modulus test, Hamburg wheel tracking test and tensile-strength ratio to evaluate cracks, rutting and moisture resistance of mixtures. RESULTS : The indirect tensile strength of fiber reinforced glass increased about 139.4%. As a result of comparing the master curves obtained by the dynamic modulus test, the elasticity was low in the low temperature region and high in the high temperature region when the glass fiber was reinforced. The glass fiber contents of PEGS 0.3%, Micro PPGF 0.1% and Macro PPGF 0.3% showed the highest moisture resistance and rutting resistance. CONCLUSIONS : The test results show that use of glass fiber reinforcement can increase the resistance to cracking, rutting, and moisture damage of asphalt mixtures. It is also necessary to validate the long-term performance of recycled asphalt mixtures with glass fiber using full scale pavement testing and field trial construction.

Estimation of Fracture Toughness of Reactor Pressure Vessel Steels Using Automated Ball Indentation Test

  • Byun, Thak-Sang;Kim, Joo-Hark;Lee, Bong-Sang;Yoon, Ji-Hyun;Hong, Jun-Hwa
    • 한국원자력학회:학술대회논문집
    • /
    • 한국원자력학회 1997년도 춘계학술발표회논문집(2)
    • /
    • pp.129-136
    • /
    • 1997
  • The automated ball indentation(ABI) test was utilized to develop a semi-nondestructive method for estimating the fracture toughness( $K_{JC}$ ) in the transition temperature range. The key concept of the method is that the indentation deformation energy to the load at which the mean ball-specimen contact pressure reaches the fracture stress is related to the fracture energy of the material. ABI tests were performed for the reactor pressure vessel(RPV) base and weld metals at the temperatures of-15$0^{\circ}C$~$0^{\circ}C$ and the fracture toughness (estimated $K_{JC}$ ) was calculated from the indentation load-depth data. For all steels the temperature dependence of the estimated fracture toughness was almost the same as that ASTM $K_{JC}$ master curve The reference temperatures( $T_{o}$)of the steels were determined form the estimated $K_{JC}$ versus temperature curves. The reference temperature was well correlated with the index temperature of 41J Charpy impact energy( $T_{41J}$).).).

  • PDF

Creep strain modeling for alloy 690 SG tube material based on modified theta projection method

  • Moon, Seongin;Kim, Jong-Min;Kwon, Joon-Yeop;Lee, Bong-Sang;Choi, Kwon-Jae;Kim, Min-Chul
    • Nuclear Engineering and Technology
    • /
    • 제54권5호
    • /
    • pp.1570-1578
    • /
    • 2022
  • During a severe accident, steam generator (SG) tubes undergo rapid changes in the pressure and temperature. Therefore, an appropriate creep model to predict a short term creep damage is essential. In this paper, a novel creep model for Alloy 690 SG tube material was proposed. It is based on the theta (θ) projection method that can represent all three stages of the creep process. The original θ projection method poses a limitation owing to its inability to represent experimental creep curves for SG tube materials for a large strain rate in the tertiary creep region. Therefore, a new modified θ projection method is proposed; subsequently, a master curve for Alloy 690 SG material is also proposed to optimize the creep model parameters, θi (i = 1-5). To adapt the implicit creep scheme to the finite element code, a partial derivative of incremental creep with respect to the stress is necessary. Accordingly, creep model parameters with a strictly linear relationship with the stress and temperature were proposed. The effectiveness of the model was validated using a commercial finite element analysis software. The creep model can be applied to evaluate the creep rupture behavior of SG tubes in nuclear power plants.