• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.4
• /
• pp.49-55
• /
• 2016

Nowadays there are magnetic sensors in a wide variety of equipment such as computers, cars, airplanes, medical and industrial instruments. In many of these applications the magnetic sensors offer safe and non-invasive means of detection and are more reliable than other technologies. The electric current in a conductor generates a magnetic field detected by this type of sensor. This work aims to define a package dedicated to an electrical current sensor using a MTJ (Magnetic Tunnel Junction) as a sensing device. Four different proposals of packaging, three variations of the chip on board (CoB) package type and one variation of the thin small outline package (TSOP) were analyzed by COMSOL modeling software by simulating a brad range of current injection. The results obtained from the thermal and magnetic analysis has proven to be very important for package improvements, specially for heat dissipation performance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.233-233
• /
• 2010

Magnetic random access memory (MRAM), based on magnetic tunnel junction (MTJ) and CMOS, is a prominent candidate among prospective semiconductor memories because it can provide nonvolatility, fast access time, unlimited read/write endurance, low operating voltage and high storage density. The etching of MTJ stack with good properties is one of a key process for the realization of high density MRAM. In order to achieve high quality MTJ stack, the use of CoFeB and IrMn magnetic films as free layers was proposed. In this study, inductively coupled plasma reactive ion etching of CoFeB and IrMn thin films masked with Ti hard mask was investigated in a $Cl_2$/Ar gas mix. The etch rate of CoFeB and IrMn films were examined on varying $Cl_2$ gas concentration. As the $Cl_2$ gas increased, the etch rate monotonously decreased. The effective of etch parameters including coil rf power, dc-bais voltage, and gas pressure on the etch profile of CoFeB and IrMn thin film was explored, At high coil rf power, high dc-bais voltage, low gas pressure, the etching of CoFeB and IrMn displayed better etch profiles. Finally, the clean and vertical etch sidewall of CoFeB and IrMn free layers can be achieved by means of thin Ti hard mask in a $Cl_2$/Ar plasma at the optimized condition.

• Journal of the Korean Magnetics Society
• /
• v.16 no.3
• /
• pp.186-191
• /
• 2006

Ferromagnetic amorphous $Ni_{16}Fe_{62}Si_8B_{14}$ and $Co_{70.5}Fe_{4.5}Si_{15}B_{10}$ layers have been devised and incorporated as free layers of magnetic tunnel junctions (MTJs) to improve MRAM reading and writing performance. The NiFeSiB and CoFeSiB single-layer film exhibited a lower saturation magnetization ($Ms=800emu/cm^3,\;and\;560emu/cm^3$, respectively) compared to that of a $Co_{90}Fe_{10}(Ms=1400emu/cm^3)$. Because amorphous ferromagnetic materials have lower Ms than crystalline ones, the MTJs incorporating amorphous ferromagnetic materials offer lower switching field ($H_{sw}$) values than that of the traditional CoFe-based MTJ. The double-barrier MTJ with an amorphous NiFeSiB free layer offered smooth surface resulting in low bias voltage dependence, and high $V_h\;and\;V_{bd}$ compared with the values of the traditional CoFe-based MTJ.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.200-200
• /
• 2013

기존 메모리 반도체에 비교해 빠른 재생속도와 높은 집적도, 비휘발성 등의 특성을 가지는 MRAM (Magnetic Random Access Memory)은 DRAM, flash memory 등을 대체할 수 있는 차세대 기억 소자로서 CoFeB/MgO/CoFeB로 구성된 한 개의 MTJ (Magnetic Tunnel Junction)를 단위 메모리로 사용한다. 이 MTJ 물질들은 고밀도 플라즈마를 이용한 건식 식각공정시 Cl2, BCl3 등과 같은 chlorine 을 포함한 가스를 이용하여 왔으나 식각 후 sidewall에서 발생하는 부식과 식각 선택비 확보의 어려움 등으로 마스크 물질에 제약을 받고 소자 특성이 감소하게 되는 등의 문제가 있다. 따라서 이러한 식각 문제점을 해결하기 위한 대안으로 noncorrosive 가스인 CO/NH3, CH3OH, CH4 등을 이용한 MTJ 식각 연구가 진행되어 오고 있으며 이중 CO/NH3 혼합가스는 부식성이 없고 hard mask와의 높은 선택비를 가지는 기체로 CO gas에 NH3 gas를 첨가하게 되면 etch rate이 증가하는 특성을 보인다. 또한 rf pulse-biased power를 이용하여 이온의 입사를 시간에 따라 제어함으로써 pulse off time 때 etch gas와 MTJ 물질간의 chemical reaction을 향상시킬 수 있다. 따라서 본 연구에서는 CO/NH3 혼합가스를 이용하여 다양한 rf pulse-biased power 조건에서 MTJ 물질인 CoFeB, MgO와 hard mask 물질인 W을 식각 한 뒤 식각특성을 분석하였으며 MTJ surface의 chemical binding state, surface roughness 측정을 진행하였다. 식각 샘플의 측정은 Alpha step profiler, XPS (X-ray Photoelectron Spectroscopy), AFM (Atomic Force Microscopy)를 통해 진행되었다. Time-averaged pulse bias에서는 duty ratio가 감소할수록 etch rate의 큰 감소 없이 CoFeB/W, MgO/W 물질의 etch selectivity가 향상됨을 확인할 수 있었으며 pulse off time 구간에서의 chemical reaction 향상으로 인해 식각부산물의 재증착이 감소하고 CoFeB의 surface roughness가 감소하는 것을 확인하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.2
• /
• pp.110-116
• /
• 2004

We propose a novel sensing scheme, which operates by sensing the difference in voltage between a memory cell and a reference cell for a magneto-resistive random access memory (MRAM). A new midpoint-reference generation circuit is adopted for the reference cell to improve the sensing margin and to guarantee correct operation of sensing circuit for wide range of tunnel magneto resistance (TMR) voltages. In this scheme, the output voltage of the reference cell becomes nearly the midpoint between the cell voltages of high and low states even if the voltage across the magnetic tunnel junction (MTJ) varies.

• Journal of Magnetics
• /
• v.15 no.4
• /
• pp.185-189
• /
• 2010

Spin polarized tunneling through a hybrid tunnel barrier of a Spin filter (SF) based on a EuO ferro-magnetic semiconductor and an organic semiconductor (OSC) (rubrene in this case) was investigated. For quasi-magnetic tunnel junction (MTJ) structures, such as Co/rubrene/EuO/Al, we observed a strong spin filtering effect of the EuO layer exhibiting I-V curves with high spin polarization (P) of up to 99% measured at 4 K. However, a magnetoresistance (MR) value of 9% was obtained at 4.2 K. The low MR compared to the high P could be attributed to spin scattering caused by structural defects at the interface between the EuO and rubrene, due to nonstoichiometry in the EuO.

• Journal of the Korean Magnetics Society
• /
• v.12 no.2
• /
• pp.68-72
• /
• 2002

In this research, the effects of capacitance to the access time were studied at the junction area of tunneling magnetoresistance when these were used as memory devices. These results were obtained by applying electric signal input and magnetic field was not used. We applied bipolar square waves of 1MHz to the MTJ samples to obtain the results and time constant ($\tau$) calculated by observing wave responses utilizing an oscilloscope. And time constant was compared with junction area. Each part of MTJ sample, such as electrical pad, lead and contact area, was modeled as an electrical equivalent circuit based on experimental results. For the 200㎛$\times$200㎛ cell, junction capacitance was 90 pF. Also, measurement and simulation results were compared, which showed those similarity.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2011.12a
• /
• pp.29-30
• /
• 2011

We have demonstrated the fabrication of sub 30 nm MTJ pillars with PMA characteristics. The multi-step IBE process performed at $45^{\circ}$ and $30^{\circ}$, using NER resulted in almost vertical side profiles. There deposition on the sidewalls of the NER prevented lateral etching of the resist hard mask allowing vertical MTJ side profile formation without any reduction in the lithographically defined resist lateral dimensions. For the 28nm STT-MTJ pillars, the measured TMR ratio was 13 % with resistance of 1 $k{\Omega}$, which was due to remaining redeposition layers less than 0.1 nm thick. With further optimization in multi-step IBE conditions, it will be possible to fabricate fully operating sub 30 nm perpendicular STT-MTJ structures for application to future non-volatile memories.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.8
• /
• pp.688-693
• /
• 2001

A series of Fe/CeO$_2$/Fe$_{75}$Co$_{25}$ tunnel junctions (Magnetic Tunnel Junction, MTJ) having CeO$_2$ barrier layers from 30 to 90$\AA$ in thickness were prepared by ion beam sputtering (IBS) method. In order to compare the properties of MTJs, Fe/Al oxide/Fe-Co tunnel junctions were also prepared. Some junctions with a CeO$_2$ barrier layer showed the ferromagnetic tunneling effect and the highest MR ratio at room temperature was 5%. The electric resistance of junctions with a CeO$_2$ barrier layer was higher that that of junctions with an Al oxide barrier. On the other hand, The interface analysis of the Fe/CeO$_2$ bilayer was conducted by means of X-ray photoelectron spectroscopy (XPS). It was found that CeO$_2$ was decomposed to Ce and $O_2$ during sputtering, and Fe was oxidized with these decomposed $O_2$ molecules. The reduction of both electric resistance and MR ratio may be associated with the decomposed Ce in the barrier layer.r.r.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.356.2-356.2
• /
• 2014

Spin Transfer Torque (STT) is of great interest in data writing scheme for the Magneto-resistive Random Access Memory (MRAM) using Magnetic Tunnel Junction (MTJ). Scalability for high density memory requires ferromagnetic electrodes having the perpendicular magnetic easy axis. We investigated CoZr as the ferromagnetic electrode. It is observed that interfacial magnetic anisotropy is preferred perpendicular to the plane with thickness dependence on the interfaces with Pt layer. The anisotropy energy (Ku) with thickness dependence shows a change of magnetic-easy-axis direction from perpendicular to in-plane around 1.2 nm of CoZr. The interfacial anisotropy (Ki) as the directly related parameters to switching and thermal stability, are estimated as $1.64erg/cm^2$ from CoZr/Pt multilayered system.