• 대한기계학회논문집A
• /
• 제20권5호
• /
• pp.1468-1476
• /
• 1996

Surface integrity is dictated by the fabrication process of the metal part. In this work, steel specimens were prepared under various mechine conditions to achieve different degrees of deformation state. The tribological characteristics of the speciments were tested using a pin-on-disk type apparatus and other surface characterization tools. It is shown that though frictional characteristics are similar, the wear rate is significantrly affected by the properties of the surface. In the case of steel, surface cracks resulted in high wear despite the relatively high hardness of the specimen. Also, the sliding action were found to reduce the residual stress on the surface. These results indicate that there is a strong relationship between surface integrity and the tribological properties of steel, and therefore the machining condition should be optimized woth respect to tribological performance of a steel part.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.19-24
• /
• 2003

Recently, various efforts to make more speedy and precision machine tool to improve productivity and also various efforts to solve environmental problem are going on, so that dry cutting in manufacturing industry, which needs environmental conscious design and development of manufacturing technique, is becoming a very important assignment to solve. Because dry cutting does not use cutting fluid, we need other methods that can be used instead of cutting fluid, which does cooling, lubricating, chip washing, and anti-corrosion. Especially, because turning is a continuous work, the consideration of tool life and surface roughness due to continuous heat and poor lubrication is important. The purposes of this paper are the consideration of how well the compressed air can work instead of cutting fluid, and also the development of the method to select the optimum machining condition by the minimum numbers of experiments through the Taguchi method.

• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.117-122
• /
• 1998

Glass fiber epoxy composite material is widely used in the structures of aircrafts, robots and other machines because of their high specific strength, high specific stiffness and high damping. In order for the composite materials to be used in the aircraft structures or machine elements, accurate surfaces for bearing mounting or joint must be provided, which require precise machining. In this paper, the machinability of the glass fiber epoxy composite material was experimentally investigated. The results can be summarized as follows : 1. The entrance of hole is very good manufacturing existing, but exit come to occur sever surface exfoliation. 2. The cutting force in drilling of the glass fiber epoxy composite material is decreased as the drilling speed increased. 3. If the glass fiber epoxy composite material is drilling by the standard twist drill, then the hole recommand cutting condition is spindle speed 400∼600rpm, feed 40∼50mm/min.

• 대한기계학회논문집A
• /
• 제24권11호
• /
• pp.2786-2795
• /
• 2000

Recently, the technology for internal polishing is needed for ultra-clean machining for the prevention of corrosion and pollution of parts is the area of high technology industries such as semiconductor, electronics, telecommunication optics, aerospace, and motors. In this study, an internal polishing system using the magnetic force was developed for the production of ultra-clean tubes with averaged surface roughness ranging from 0.2㎛ to 0.05㎛ or less, and magnetic abrasives composed of WC/Co powder were developed, After finding the optimal condition on each, machining characteristics using newly developed abrasive were analyzed. Form the results obtained by experimental design method, the optimal polishing condition was analyzed and, thhereafter internal polishing was done.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.125-130
• /
• 1994

Recently,manufacturing work been transformed to small acale production from with various items to act up to user's expectation from mass production with a little items required in the past. The FMS using NC type mother machinaries has been applied actively also in domestic manufacturing line to meet thus tendancy, but there are many machining troubles occured in work process not be settled yet. Nowdays high efficiency has been required no less than high precision in grinding work for the improvement of productivity. In this study, to represent more advanced FMS can be adapted to thus situation In-process type monitoring method using AE and Current sensors is suggested to investigatethe machining condition in grinding process. As results from this experimental study, is is recoqnized well that grinding conditions and dressing point of in time can be estimated effectively using monitoring method suggested. Furthermore, surface shape of grinding wheel on voluntary point of in time can be predicted indirectly through the observation and comparison of AE signal waveform obtained as performance of continuous dressing work.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1991년도 춘계학술대회 논문집
• /
• pp.22-31
• /
• 1991

Machining with boring bars frequently induce chatter vibration because of the low stiffness and damping of cantilever shape of boring bars. To increase stiffness and damping, a carbon fiber epoxy composite boring bar was designed, manufactured and tested. The natural frequency of the carbon fiber epoxy composite boring bar in the free-free end condition was incerased more than 50% over that of the steel boring bar, and the damping of the carbon fiber epoxy composite boring bar was also increased 450%. The fundamental natural frequency of the carbon fiber epoxycomposite boring bar in the cantilever beam condition was found to be increased 20-30% over that of the steel boring bar in overhang length range 140-200mm. In machining S45C tapered workpieces, the limit of the overhang length of the steel boring bar was about 170mm in cutting speed 140m/min.

• 한국공작기계학회논문집
• /
• 제10권5호
• /
• pp.130-136
• /
• 2001

The purpose of this study is an evaluation of flat end mills to develop appropriate tools for the high speed machining. First of all, several flat end mills which are produced by different makers are selected to analyze the performances of the tools. Experimental works are also executed to measure cutting farce, tool wear and surface roughness for different cutting conditions. And then the results are compared and analyzed for developing optimal cutting tool in the high speed condition.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.675-680
• /
• 2009

Because of high specific stiffness, the aluminum alloy has been used for various industry field. Specially, the heat-treated aluminum alloy is difficult-to-machine material and machining test is necessary to evaluate and improve the machinability. In order to manufacture the functional part, appropriate cutting condition is selected by considering surface quality, machining time, and workpiece deflection by cutting force. In this investigation, the machinability of A16061-T6 is estimated by changing cutting conditions. The variable cutting conditions are cutting speed, depth of cutting, and feed rate. The estimation is done by analysis of cutting force, surface roughness, and surface shape according to the change of cutting conditions.

• 한국공작기계학회논문집
• /
• 제18권1호
• /
• pp.76-82
• /
• 2009

To obtain the surface roughness with nano order, we need a ultra-precision machine, cutting condition, and materials. In this paper, the cutting condition for getting nano order smooth surface of core have been examined experimentally by the ultra-precision machine and diamond wheels. The effects of the cutting velocity, the feed rate and depth of cut on the surface roughness were studied. And also, the surface roughness was measured by the Form Talysurf series PGI 840. The champion data of developed core was surface roughness Rmax 24.6nm, figure accuracy Rmax 68.9nm.

• 산업공학
• /
• 제7권3호
• /
• pp.155-168
• /
• 1994

In computer integrated manufacturing environment, tool management plays an important role in controlling tool performance for machining operations. Knowledge of tool behavior during the cutting process and effective tool-behavior prediction contribute to controlling machine costs by avioding production delays and off-target parts due to tool failure. The purpose of this paper is to review and develop the tool condition monitoring scheme for drilling operation to assure a fast corrective response to minimize the damage if tool failures occur. If one desires to maximize system through-put and product quality as well as tooling resources, within an economic environment, real-time tool sensing system and information processing system can be coupled to provide the necessary information for the effective tool management. The example is demonstrated as to drilling operation when the aluminum composites are drilled with carbide-tipped HSS drill bits. The example above is limited to the situation that the tool failure mode of drill bits is wear.