• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.796-805
• /
• 2014

A digital controller with a low-power approach for point-of-load synchronous buck converters is discussed and compared with its analog counterpart to confirm its feasibility for system integration. The tri-mode digital controller IC in $0.35{\mu}m$ CMOS process is presented to demonstrate solutions that include a PID, quarter PID, and robust RST compensators. These compensators address the steady-state, stand-by, and transient modes according to the system operating point. An idle-tone free condition for ${\Sigma}-{\Delta}$ DPWM reduces the inherent tone noise under DC-excitation. Compared with that of the traditional approach, this condition generates a quasi-pure modulation signal. Experimental results verify the closed-loop performances and confirm the power-saving mechanism of the proposed controller.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.565-570
• /
• 2011

In this paper, the analytical tuning rules of the proportional-integral-derivative (PID) controller have been derived for a broad class of stable, integrating, and unstable processes without time delay. On the basis of the renowned internal model control (IMC) design principles and the two-degree-of-freedom (2DOF) control structure, the proposed method can be effectively used for obtaining the enhanced performances of both the disturbance rejection as well as the set-point tracking problems, since the design scheme is simple, straightforward, and can be easily implemented in the process industry. Several processes without time delay are employed to demonstrate the improved closed-loop performance of the proposed controller design in compared with the other well-known design methods in terms of the same degree of robustness.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.546-551
• /
• 2004

In this paper, a level controller is designed with the neuro-fuzzy model based on Takagi-Sugeno fuzzy system. The fuzzy system is employed as the controller, which can be tuned by the neural network mechanism based on a gradient descent technique. The tuning mechanism will provide an optimal process input by forcing the process error to zero. The proposed controller provides the online tunable mode to adjust the consequent membership function parameters. The controller is implemented with M-file and graphic user interface (GUI) of Matlab program. The program uses MPIBM3 interface card to connect with the industrial processes In the experimentation, the proposed method is tested to vary of the process parameters, set points and load disturbance. Processes of one tank and two tanks are used to evaluate the efficiency of our controller. The results of the both processes are compared with two PID systems that are 3G25A-PIDO1-E and E5AK of OMRON. From the comparison results, our controller performance can be archived in the case of more robustness than the two PID systems.

• Proceedings of the KIEE Conference
• /
• 1998.07b
• /
• pp.678-680
• /
• 1998

Based on fuzzy logic algorithm this paper constructed fuzzy logic controller for automated vehicles. For passenger's convenience especially comfortability controller need to reduce the frequency of input variable's changing. So we established membership functions for comfortability as mil as speed following. It made possible to control comfortability directly. To demonstration the efficiency of fuzzy logic controller, we carried out simulation with a Automobile's transfer function. First, we designed the PID controller by using Ziegler-Nichols tunning method. Second, we calculated time response for each controller, then we compared the speed patterns of fuzzy controlled system and PID controlled system. Also we compared the difference of input variable. By comparing two controller's response, we can confirm the merit of fuzzy controller about comfortability. Fuzzy controller can reduce input changing frequency.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.333-336
• /
• 1992

In this paper, We propose a PID-type of self-tuning algorithm which is based on the parameter estimation and the minimization of the cost function. We use the CARIMA model for parameter estimation and determine the discrete PID controller parameters by minimizing the cost function which considers the quadratic deviations of the predicted output over the set-point as well as the control efforts. Also, The algorithm is extended by incorporating constraints of the control signal. Simulations are performed to illustrate the efficiency of the proposed method.

• Journal of Biosystems Engineering
• /
• v.38 no.4
• /
• pp.255-263
• /
• 2013

Purpose: It is not easy to drive a rice-transplanter avoiding underlapped or overlapped transplanting in paddy fields. An automated guidance system for the riding-type rice-transplanter would be necessary to operate the rice-transplanter autonomously or to assist the beginning drivers as a driving aid. Methods: A prototype of guidance system was composed of embedded computers, RTK-GPS, and a power-steering mechanism. Two Kalman filters were adopted to overcome sparse positioning data (1 Hz) from the RTK-GPS. A global Kalman filter estimated the posture of rice-transplanter every one second, and a local Kalman filter calculated the posture from every new estimation of the global Kalman filter with an interval of 200 ms. A PID controller was applied to the row-following mode control. A control method of U-turning mode was developed as well. A stepping motor with a reduction gear set was used to rotate the shaft of steering wheel. Results: Test trials for U-turning and row-following modes were done in a paddy field after some parameters have been tuned at the ground speed range of 0.3 ~ 1.2 m/s. The minimum RMS error of offset was 3.13 cm at the ground speed of 0.3 m/s while the maximum RMS error was 13.01 cm at 1.2 m/s. The offset RMS error tended to increase as the ground speed increased. The target point distance, LT also affected the system performance and PID controller parameters should be adjusted on different ground speeds. Conclusions: A target angle-based PID controller plus stationary steering angle controller made it possible for the rice-transplanter to steer autonomously by following a reference line accurately and even on U-turning mode. However, as condition in paddy fields is very complicated, the system should control the ground speed that prevents it from deviating too much due to ditch and slope.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.710-714
• /
• 2005

A dynamical analysis and PID control of a compressed gas expulsion system is performed. The purpose of this study is to develop a compressed gas discharging system and to verify the validity of the system. The electro-hydraulic servo valve is modeled as a 3th order transfer function to calculate flow force affecting expulsion valve is significantly considered. The friction force in the expulsion valve is considered as a nonliner model of stribeck effect. The dynamic characteristics of this system is examined by the computer simulation. The position control of the expulsion valve is performed by PID controller.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.90-94
• /
• 2004

Among various modern control theories, PID control has been well used for several decades. PID algorithms needs son tuning methods are used for selecting PID parameters. But in some cases various kinds of performance indices are used instead of well-known tuning rules, and so variable type of performance index must be tested so that controllers, output characteristics and disturbance rejection property meets some specifications. In this paper, linear conbinational type of performance using error signal, time, control input and robustness is used to the PID control of air conditioning system. By the 2 DOF PID parmeters minimizing perfromacne index, controllers, output characteristics and robustness properties are analyzed. Simulations are done with MATLAB m file and mdl files.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.9
• /
• pp.34-40
• /
• 1999

In order to establish the design technique of the robust current controller in d.c series wound motor driver system, this paper proposes a method of the compensated Bang-Bang current control using d.c series wound motor driver system under the improperly variable load to get minimum time for the torque control. The compensated Bang-Bang current controller structure is simpler than that of PID plus Bang-Bang controller. This paper shows that a general 16 bits microprocessor is efficiently used to implement such an algorithm. The calculation time of software is extremely small when compared with that of conventional PID plus Bang-Bang controller. Both nonlinear operating characteristics of digital switching elements and describing function methods are used for the analysis and synthesis. Real-time implementation of the compensated Bang-Bang current controller is achieved. The concept of design strategy of the control and the PWM waveform generation algorithms are presented in this paper.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1110-1115
• /
• 2004

Water covers two-thirds of the earth and has a great influence on the future existence of all human being. Thailand has extensive coastline and near shore water that contain vast biological and mineralogical resources. The rivers and canals can be found around the country especially in the Bangkok, which once called the Venice of the East. Autonomous underwater robot (AUR) will be soon a tool to help us better understand water resources and other environmental issues. This paper presents the design and basic control of a six-degree of freedom AUR "Chalawan", which was constructed to be used as a testbed for shallow. It is a simple low cost open-frame design, which can be modified easily to supports various research areas in the underwater environment. It was tested with a conventional proportional-integral-derivative (PID) controller. After fine-tuning of the controller gains, the results showed the controller's good performances. In the future, the dynamic model of the robot will be analyzed and identified. The advanced control algorithm will be implemented based on the obtained model.