• Journal of Electrochemical Science and Technology
• /
• 제10권2호
• /
• pp.196-205
• /
• 2019

Ni-rich layered oxides $Li(Ni_xCo_yMn_z)O_2$ (x + y + z = 1) have been extensively studied in recent times owing to their high capacity and low cost and can possibly replace $LiCoO_2$ in the near future. However, these layered oxides suffer from problems related to the capacity fading, thermal stability, and safety at high voltages. In this study, we use surface coating as a strategy to improve the thermal stability at higher voltages. The uniform and conformal $Al_2O_3$ coating on prefabricated electrodes using atomic layer deposition significantly prevented surface degradation over prolonged cycling. Initial capacity of 190, 199, 188 and $166mAh\;g^{-1}$ is obtained for pristine, 2, 5 and 10 cycles of ALD coated samples at 0.2C and maintains 145, 158, 151 and $130mAh\;g^{-1}$ for high current rate of 2C in room temperature. The two-cycle $Al_2O_3$ modified cathode retained 75% of its capacity after 500 cycles at 5C with 0.05% capacity decay per cycle, compared with 46.5% retention for a pristine electrode, at an elevated temperature. Despite the insulating nature of the $Al_2O_3$ coating, a thin layer is sufficient to improve the capacity retention at a high temperature. The $Al_2O_3$ coating can prevent the detrimental surface reactions at a high temperature. Thus, the morphology of the active material is well-maintained even after extensive cycling, whereas the bare electrode undergoes severe degradation.

• Journal of Microbiology and Biotechnology
• /
• 제28권1호
• /
• pp.95-104
• /
• 2018

Biosurfactants or microbial surfactants are surface-active biomolecules that are produced by a variety of microorganisms. Biodegradability and low toxicity have led to the intensification of scientific studies on a wide range of industrial applications for biosurfactants in the field of environmental bioremediation as well as the petroleum industry and enhanced oil recovery. However, the major issues in biosurfactant production are high production cost and low yield. Improving the bioindustrial production processes relies on many strategies, such as the use of cheap raw materials, the optimization of medium-culture conditions, and selecting hyperproducing strains. The present work aims to obtain a mutant with higher biosurfactant production through applying mutagenesis on Bacillus subtilis SPB1 using a combination of UV irradiation and nitrous acid treatment. Following mutagenesis and screening on blood agar and subsequent formation of halos, the mutated strains were examined for emulsifying activity of their culture broth. A mutant designated B. subtilis M2 was selected as it produced biosurfactant at twice higher concentration than the parent strain. The potential of this biosurfactant for industrial uses was shown by studying its stability to environmental stresses such as pH and temperature and its applicability in the oil recovery process. It was practically stable at high temperature and at a wide range of pH, and it recovered above 90% of motor oil adsorbed to a sand sample.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.136.1-136.1
• /
• 2015

In the present study, UHF (320 MHz) in combination with RF (13.56 MHz) plasmas was used for the synthesis of hydrogenated silicon nitride (SiNx:H) films by PECVD process at low temperature. RF/UHF hybrid plasmas were maintained at a fixed pressure of 410 mTorr in the N2/SiH4 and N2/SiH4/NH3 atmospheres. To investigate the radical generation and plasma formation and their control for the growth of the film, plasma diagnostic tools like vacuum ultraviolet absorption spectroscopy (VUVAS), optical emission spectroscopy (OES), and RF compensated Langmuir probe (LP) were utilized. Utilization of RF/UHF hybrid plasmas enables very high plasma densities ~ 1011 cm-3 with low electron temperature. Measurements using VUVAS reveal the UHF source is quite effective in the dissociation of the N2 gas to generate more active atomic N. It results in the enhancement of the Si-N bond concentration in the film. Consequently, the deposition rate has been significantly improved up to 2nm/s for the high rate synthesis of highly transparent (up to 90 %) SiNx:H film. The films properties such as optical transmittance and chemical composition are investigated using different analysis tools.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.210.1-210.1
• /
• 2015

최근 산화물 반도체에 대한 연구가 활발하게 이루어지고 있다. 비정질 산화물 반도체인 In-Ga-Zn-O (IGZO)는 기존의 비정질 실리콘에 비해 공정 단가가 낮으며 넓은 밴드 갭으로 인한 투명성을 가지고 있고, 저온 공정이 가능하여 다양한 기판에 적용이 가능하다. 반도체의 공정 과정에서 열처리는 소자의 특성 개선을 위해 필요하다. 일반적인 열처리 방법으로 furnace 열처리 방식이 주로 이용된다. 그러나 furnace 열처리는 시간이 오래 걸리며 일반적으로 고온에서 이루어지기 때문에 최근 연구되고 있는 유리나 플라스틱, 종이 기판을 이용한 소자의 경우 기판이 손상을 받는 단점이 있다. 이러한 단점들을 극복하기 위하여 저온 공정인 마이크로웨이브를 이용한 열처리 방식이 제안되었다. 마이크로웨이브 열처리 기술은 소자에 에너지를 직접적으로 전달하기 때문에 기존의 다른 열처리 방식들과 비교하여 에너지 전달 효율이 높다. 또한 짧은 공정 시간으로 공정 단가를 절감하고 대량생산이 가능한 장점을 가지고 있으며, 저온의 열처리로 기판의 손상이 없기 때문에 기판의 종류에 국한되지 않은 공정이 가능할 수 있을 것으로 기대된다. 따라서 본 연구에서는 마이크로웨이브 열처리가 소자의 전기적 특성 개선에 미치는 영향을 확인하였다. 제작된 IGZO 박막트렌지스터는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. RCA 클리닝을 진행한 후 RF sputter를 사용하여 In-Ga-Zn-O (1:1:1)을 70 nm 증착하였다. 이후에 Photo-lithography 공정을 통하여 active 영역을 형성하였고, 전기적 특성 평가가 용이한 junctionless 트랜지스터 구조로 제작하였다. 후속 열처리 방식으로 마이크로웨이브 열처리를 1000 W에서 2분간 실시하였다. 그리고 기존 열처리 방식과의 비교를 위해 furnace를 이용하여 N2 가스 분위기에서 $600^{\circ}C$의 온도로 30분 동안 열처리를 실시하였다. 그 결과, 마이크로웨이브 열처리를 한 소자의 경우 기존의 furnace 열처리 소자와 비교하여 우수한 전기적 특성을 나타내는 것을 확인하였다. 따라서, 마이크로웨이브를 이용한 열처리 공정은 향후 저온 공정을 요구하는 소자 공정에 활용될 수 있을 것으로 기대된다.

• 한국환경보건학회지
• /
• 제26권3호
• /
• pp.1-10
• /
• 2000

Although microorganisms play an important role in composting process, researches on the effective microorganism (EM) in composting process are rarely reported. In this study, three stages of work performed 1) investigation of composting facility 2) sample collection and isolation of the EM 3) lab-scale composting by seeding the isolated EM. For this, purpose, physical, chemical, and biological characteristics, such as temperature, moisture content, organic matter, pH population of microorganism, etc., were investigated during the process and the results were compared with those of a control(non-seeded). In the composting facility, the most active degradation of food waste was suppsed to occur in 10-11th day of composting by observing the temperature and CO2 emission. The population of bacterial and fungi was highest in thermophilic stage. Meanwhile that of actinomycetes and yeast was relatively uniform during the process. In the lab-scale test, the thermophilic stage was maintained longer(more than 9 days in 17 days of experiment) in the seeded which was favored for the high reduction of organic matter and moisture. Reduction rates of lipids and salinity were also increased in the seeded. It confirmed these results that the population of microorganisms in the seeded was observed higher in several orders than the control. However, pH of the seeded was maintained as low as about 4.5 throughout the experiment except the final period of the process. Meanwhile, pH of the control rose in the early stage of the experiment. This was probably due that the seeded microorganisms collected from the composting facility was adapted to the low pH environment.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.328-336
• /
• 2005

Effects of surface defect distribution on flame instability during flame-surface interaction are experimentally investigated. To examine the chemical quenching phenomenon, we prepared thermally grown silicon oxide plates with well-defined defect density. Ion implantation was used to control the number of defects, i.e. oxygen vacancies. In an attempt to preferentially remove the oxygen atoms from silicon dioxide surface, argon ions with low energy level from 3keV to 5keV were irradiated at the incident angle of $60^{\circ}C$. Compositional and structural modification of $SiO_2$ induced by low-energy $Ar^+$ ion irradiation has been characterized by Atomic Force Microscopy (AFM) and X-ray Photoelectron Spectroscopy (XPS). The analysis shows that as the ion energy increases, the number of structural defect also increases and non-stoichiometric condition of $SiO_x(x{\le}2)$ plates is enhanced. From the quenching distance measurements, we found out that when the surface temperature is under $300^{\circ}C$, the quenching distance decreases on account of reduced heat loss; as the surface temperature increases over $300^{\circ}C$, however, quenching distance increases despite reduced heat loss effect. Such aberrant behavior is caused by heterogeneous chemical reaction between active radicals and surface defect sites. The higher defect density, the larger quenching distance. This results means that chemical quenching is governed by radical adsorption and can be parameterized by the oxygen vacancy density on the surface.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.341-341
• /
• 2012

Recently, oxide semi-conductor materials have been investigated as promising candidates replacing a-Si:H and poly-Si semiconductor because they have some advantages of a room-temperature process, low-cost, high performance and various applications in flexible and transparent electronics. Particularly, amorphous indium-gallium-zinc-oxide (a-IGZO) is an interesting semiconductor material for use in flexible thin film transistor (TFT) fabrication due to the high carrier mobility and low deposition temperatures. In this work, we demonstrated improvement of flexibility in IGZO TFTs, which were fabricated on polyimide (PI) substrate. At first, a thin poly-4vinyl phenol (PVP) layer was spin coated on PI substrate for making a smooth surface up to 0.3 nm, which was required to form high quality active layer. Then, Ni gate electrode of 100 nm was deposited on the bare PVP layer by e-beam evaporator using a shadow mask. The PVP and $Al_2O_3$ layers with different thicknesses were used for organic/inorganic multi gate dielectric, which were formed by spin coater and atomic layer deposition (ALD), respectively, at $200^{\circ}C$. 70 nm IGZO semiconductor layer and 70 nm Al source/drain electrodes were respectively deposited by RF magnetron sputter and thermal evaporator using shadow masks. Then, IGZO layer was annealed on a hotplate at $200^{\circ}C$ for 1 hour. Standard electrical characteristics of transistors were measured by a semiconductor parameter analyzer at room temperature in the dark and performance of devices then was also evaluated under static and dynamic mechanical deformation. The IGZO TFTs incorporating hybrid gate dielectrics showed a high flexibility compared to the device with single structural gate dielectrics. The effects of mechanical deformation on the TFT characteristics will be discussed in detail.

• Smart Structures and Systems
• /
• 제6권8호
• /
• pp.939-951
• /
• 2010

A low-cost wireless sensor network (WSN) solution with highly expandable super and simple nodes was developed. The super node was designed as a sensing unit as well as a receiving terminal with low energy consumption. The simple node was designed to serve as a cheaper alternative for large-scale deployment. A 12-bit ADC inputs and DAC outputs were reserved for sensor boards to ease the sensing integration. Vibration and thermal field tests of the Chi-Lu Bridge were conducted to evaluate the WSN's performance. Integral acceleration, temperature and tilt sensing modules were constructed to simplify the task of long-term environmental monitoring on this bridge, while a star topology was used to avoid collisions and reduce power consumption. We showed that, given sufficient power and additional power amplifier, the WSN can successfully be active for more than 7 days and satisfy the half bridge 120-meter transmission requirement. The time and frequency responses of cables shocked by external force and temperature variations around cables in one day were recorded and analyzed. Finally, guidelines on power characterization of the WSN platform and selection of acceleration sensors for structural health monitoring applications were given.

• 한국축산식품학회지
• /
• 제22권2호
• /
• pp.172-178
• /
• 2002

우유 중에는 여러 종류의 생리활성물질과 우리 몸에 꼭 필요한 비타민이 매우 소량 함유되어 있어, 그 강화를 목적으로 유가공 산업의 발전과 더불어 다양한 비타민 강화우유가 소개되고 있다. 이에 본 연구에서는 가공 처리 및 비타민 강화 방법에 따른 비타민류의 손실율을 조사하였다. 실험 결과, UHT 처리 후에 비타민 C는 60~70% 가까운 손실율을 보였으며, 비교적 열에 안정하다고 알려진 지용성 비타민인 비타민 D$_3$와 비타민 E도 30~40%의 손실율을 보여 주었다. 이에 반해 비타민을 캡슐 형태로 강화하였을 경우에는 수용성 비타민의 손실율은 상대적으로 매우 낮음을 알 수 있었다. 이는 캡슬에 의해 열뿐 아니라 산소, 빛 등이 효과적으로 차단되어 비타민의 손실이 최소화된 것이라 생각된다. 따라서 열처리에 의한 시유 및 강화우유 중의 비타민의 손실을 최소화하기 위해서는 우유의 살균 온도 및 시간, 강화제 첨가 방법 등에 대한 지속적인 연구가 이루어져야 할 것으로 사료된다.

• 한국수소및신에너지학회논문집
• /
• 제24권4호
• /
• pp.340-346
• /
• 2013

Study on clean and efficient utilization technology for low rank coal with high moisture content is actively ongoing due to limited reserves of petroleum and of high grade coal and serious climate change caused by fossil fuel usage. In the present study, supercritical water gasification of low rank coal was performed. With increasing reaction temperature, content of combustible gases such as $H_2$ and $CH_4$ in the syngas increased while the $CO_2$ content decreased. As the reaction pressure increased from 210 to 300 bar, the $CO_2$ content in the syngas increased while the hydrocarbon gas content decreased. The $H_2$ and $CH_4$ content in the syngas increased slightly with pressure. With the addition of Pd, Pt, and Ru catalysts, it was possible to improve the production of $H_2$. Moreover, the increase of active metal content in the catalyst increased the $H_2$ productivity. The Ru catalyst shows the best performance for increasing the $H_2$ content in the syngas, while decreasing the $CO_2$ content.