• Environmental Engineering Research
• /
• v.13 no.3
• /
• pp.155-161
• /
• 2008

This study examined effects of the fermented leachate of food waste (FLFW) on nitrogen and phosphorous removal for domestic wastewater containing a low carbon-to-nitrogen (C/N) ratio in sequencing batch reactor (SBR). When the FLFW was not supplied in the process, release of phosphorus and excessive intake was not observed at both anaerobic and aerobic stages. On the other hand, when the FLFW was gradually added, active release of phosphorus and intake of phosphorus was noticed at an anaerobic stage and aerobic stage, respectively, resulting in improved phosphorus removal efficiency. The removal efficiency of nitrogen and phosphorus was increased from 75% and 37% (R-1, control test) to 97% and 80% (R-4, the highest substrate ratio test), respectively. In addition, although activity of the nitrogen oxidizing microorganisms was reduced when the reaction temperature was decreased to $10^{\circ}C$, the phosphorus removal efficiency was shown to increase with the addition of FLFW, indicating an independence from temperature. Overall, this study suggests that an efficient nutrients removal process can be successfully employed into a SBR when the FLFW is added to a wastewater which has a low C/N ratio.

• Journal of Environmental Science International
• /
• v.22 no.1
• /
• pp.73-81
• /
• 2013

The present work has been devoted to the catalytic reduction of $N_2O$ by $H_2$ with $Pt/SiO_2$ catalysts at very low temperatures, such as $110^{\circ}C$, and their nanoparticle sizes have been determined by using $H_2-N_2O$ titration, X-ray diffraction(XRD) and high-resolution transmission electron microscopy(HRTEM) measurements. A sample of 1.72% $Pt/SiO_2$, which had been prepared by an ion exchange method, consisted of almost atomic levels of Pt nanoparticles with 1.16 nm that are very consistent with the HRTEM measurements, while a $Pt/SiO_2$ catalyst possessing the same Pt amount via an incipient wetness technique did 13.5 nm particles as determined by the XRD measurements. These two catalysts showed a noticeable difference in the on-stream $deN_2O$ activity maintenance profiles at $110^{\circ}C$. This discrepancy was associated with the nanoparticle sizes, i.e., the $Pt/SiO_2$ catalyst with the smaller particle size was much more active for the $N_2O$ reduction. When repeated measurements of the $N_2O$ reduction with the 1.16 nm Pt catalyst at $110^{\circ}C$ were allowed, the catalyst deactivation occurred, depending somewhat on regeneration excursions.

• The Korean Journal of Malacology
• /
• v.18 no.2
• /
• pp.83-91
• /
• 2002

Reproductive cycle of natural population and artificial control experiments of gonadal development by the conditions of water temperatures-feeding and starvation of Ruditapes philippinarum were investigated by histological observations. The reproductive cycle of natural population in females and males can be categorized into five successive stages; early active (February to March), late active (April to May), ripe (April to August), partially spawned (May to October), and spent-inactive stage (August to March). In the artificial control experiments, gonadal development of this species was inhibited by the low water temperature (10$^{\circ}C$). In the experimental group which was exposed to artificial high water temperatures of 19$^{\circ}C$ and 22$^{\circ}C$, gonadal development was accelerated by the higher water temperatures and was faster (about one month) than that in natural populations. In the high water temperatures-feeding experimental group, the gonadal developmental phase was faster in the small-size group than that in the large-size group, and was faster in lower water temperature (10$^{\circ}C$)(p=0.01). The gonad developmental phases in the high water temperature (22-28$^{\circ}C$)-starvation experimental group showed faster (paired sample t-test, p=0.004) than those in the high water temperature-feeding group in females and males. In the high water temperature-feeding experimental group of female and male gonadal developments of small sized group were more sensitive than those in large sized group after 42 days cultivation, However, the gonadal development of male was more sensitive to the lower water temperature than female. On the whole, sexual maturation in the high water temperature experimental group was faster than those in the low water temperature group, and showed a significant difference (paired sample t-test, p=0.001) between female and male. In the starvation experimental group after 42 days, gonadal developments in the high water temperature-large male group showed faster than those in the high water temperature-large female group. However, in small size, gonad developmental phases showed the same pattern between feeding and starvation experimental groups. During the main spawning season, in the high water temperature-starvation experimental groups in females and males, their gonadal development showed faster than that in higher water temperature-feeding experimental group regardless of their sexes and individual sizes and showed a significant difference (paired sample t-test, p=0.004).

• Korean Journal of Food Science and Technology
• /
• v.41 no.3
• /
• pp.284-291
• /
• 2009

This study was conducted to characterize the enhanced antioxidant and anticancer activities of Berberis koreana bark following a low temperature and high pressure extraction process. The results indicate that the B. koreana bark extracted as described showed a 93% increase in DPPH radical scavenging activity. Inhibition activity of xanthine oxidase was highest by this extraction process. In addition the growth of human lung cancer cells (A549), human stomach cancer cells (AGS), human breast cancer cells (MCF-7) and human liver cancer cells (Hep3B) were inhibited by 70.8%, 86.2%, 84.3% and 62.5% respectively. These data indicate that this low temperature and high pressure extraction technique results in the efficient extraction of bioactive compounds from rigid plant materials. This process could also be combined with other techniques to improve extraction yields and identify new biologically active substances from relatively hard plants.

• Food Science and Preservation
• /
• v.22 no.5
• /
• pp.708-713
• /
• 2015

To provide the basic data to dry vegetate the sweetpotato leaves, the total contents of tannin, flavonoid and polyphenol in the methanol extract from the hot-air dried sweetpotato leaves were analyzed and DPPH radical scavenging activity, ABTS radical scavenging ability, nitrite scavenging ability, and others were comparatively analyzed. The total tannin content was decreased from Shinmi of 10.87 mg/g at $40^{\circ}C$ to 7.28 mg/g at $70^{\circ}C$ and the total flavonoid was decreased from Hayanmi of 55.37 mg/g at $40^{\circ}C$ to 39.63 mg/g at $70^{\circ}C$. That is, the low temperature drying contained more of these substances than in the high temperature drying. The DPPH radical scavenging activity was the highest in Shinmi and Hayanmi of 84.33% and 85.25% at $40^{\circ}C$, and the ABTS radical scavenging ability was a high value of over 80% in the treatment plot at $40^{\circ}C$. The nitrite scavenging ability was highest in Shinmi and Hayanmi of 76.15% and 73.74% at $40^{\circ}C$ but low at $70^{\circ}C$. That is, the antioxidant effect of the hot-air dried sweetpotato leaves was high in the sample of $40^{\circ}C$ and low in the sample of $70^{\circ}C$. Affected by the drying temperature, the high antioxidant effect is resulting from the little decrease of active ingredient when drying at low temperatures.

• Journal of Plant Biotechnology
• /
• v.49 no.3
• /
• pp.187-192
• /
• 2022

The repeated monthly or weekly subculture of plant callus is labor intensive and increases the risk of somaclonal variation from the parental callus line. The most effective method for preserving plant callus is cryopreservation, which involves storage in liquid nitrogen. However, this method cannot be applied to the callus of different plant species in the same manner, so it is difficult to develop a standardized cryopreservation method. In addition, the survival rate of the frozen callus after thawing and the regeneration rate after survival are uncertain. Therefore, it is necessary to develop a method to extend the subculture interval of plant callus in an active state. In this study, active plant calli of various species without freezing was incubated at 15℃ for 4 to 12 weeks without subculture. After 12 weeks, 8 lines of plant callus grew less than 2-fold when cultured at 25℃, but at least 2 times as much when cultured at 15℃. Moreover, total antioxidant activity did not differ significantly between plant callus recovered at 25℃ after culturing at 15℃ or at 25℃. These results show that the subculture interval can be extended at a temperature of 15℃ without need for modified medium composition or additional processes. In addition, positive results in all calli of several plant species are expected to reduce labor as well as somaclonal variation by increasing the subculture.

• Clean Technology
• /
• v.16 no.2
• /
• pp.132-139
• /
• 2010

The Cu-Mn mixed oxide catalysts with different molar ratios of Cu/(Cu+Mn) prepared by co-precipitation method have been investigated in CO oxidation at $30^{\circ}C$. The catalysts used in this study were characterized by X-ray Diffraction (XRD), $N_2$ sorption, X-ray photoelectron spectroscopy (XPS), and $H_2$-temperature programmed reduction $(H_2-TPR)$ to correlate with catalytic activities in CO oxidation. The $N_2$ adsorption-desorption isotherms of Cu-Mn mixed oxide catalysts showed a type 4 having pore range of 7-20 nm and BET surface area was increased from 17 to $205\;m^2{\cdot}g^{-1}$ with increasing of Mn content. The XPS analysis showed the surface oxidation state of Cu and Mn represented $Cu^{2+}$and the mixture of $Mn^{3+}$ and $Mn^{4+}$, respectively. Among the catalysts studied here, Cu/(Cu+Mn) = 0.5 catalyst showed the highest activity at $30^{\circ}C$ in CO oxidation and the catalytic activity showed a typical volcano-shape curve with respect to Cu/(Cu+Mn) molar ratios. The water vapor showed a prohibiting effect on the efficiency of the catalyst which is due to the competitive adsorption of carbon monoxide on the active sites of catalyst surface and finally the formation of hydroxyl group with active metals.

• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.1
• /
• pp.91-98
• /
• 1997

Y-zeolite and ${\gamma}$-Al$_2$O$_3$ were used as supports on CO and $C_3$H$_{6}$ oxidation for diesel emission control. The catalysts composed of Pd and Pt as active components were wash coated on honeycomb type ceramic substrate. The oxidation of CO and $C_3$H$_{6}$ was carried out over prepared honeycomb in a fixed bed continuous reactor in the temperature range of 20$0^{\circ}C$~50$0^{\circ}C$ and 20,000 GHSV (h$^{-1}$ ). Surface area of Y-zeolite was larger than that of ${\gamma}$-Al$_2$O$_3$ due to channel structure of Y-zeolite. Therefore, high conversion of CO and $C_3$H$_{6}$ could be obtained because of good dispersion of active metals over Y-zeolite. The honeycomb used Y-zeolite as a support showed higher $C_3$H$_{6}$ conversion than that of ${\gamma}$-Al$_2$O$_3$ due to better cracking and isomerization activity of Y-zeolite. PdPt catalyst showed high conversion of CO and $C_3$H$_{6}$ at low temperature region, 20$0^{\circ}C$~30$0^{\circ}C$, for their synergy effects. PdPt/Y-Zeolite catalyst could achieve more than 80％ conversion of $C_3$H$_{6}$ at 30$0^{\circ}C$. The use of Y-zeolite as a support increased CO and $C_3$H$_{6}$ conversion, and decreased SO$_2$ conversion very effectively. Y-zeolite found to have a good adaptability as a support for the diesel emission after treatment system.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.595-602
• /
• 2023

The EAST ICRF system operating space has been extended in power and phase control with a low-level RF system for the new double-strap antenna. Then the multi-step power and periodic phase scanning experiment were conducted in L-mode plasma, respectively. In the power scanning experiment, the stored energy, radiation power, plasma impedance and the antenna's temperature all have positive responses during the short ramp-ups of P_L;ICRF. The core ion temperature increased from 1 keV to 1.5 keV and the core heating area expanded from |Z| ≤ 5 cm to |Z| ≤ 10 cm during the injection of ICRF waves. In the phasing scanning experiment, in addition to the same conclusions as the previous relatively phasing scanning experiment, the superposition effect of the fluctuation of stored energy, radiation power and neutron yield caused by phasing change with dual antenna, resulting in the amplitude and phase shift, was also observed. The active control of RF output facilitates the precise control of plasma profiles and greatly benefits future experimental exploration.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.186-186
• /
• 2000

After LeComber et al. reported the first amorphous hydrogenated silicon (a-Si: H) TFT, many laboratories started the development of an active matrix LCDs using a-Si:H TFTs formed on glass substrate. With increasing the display area and pixel density of TFT-LCD, however, high mobility TFTs are required for pixel driver of TF-LCD in order to shorten the charging time of the pixel electrodes. The most important of these drawbacks is a-Si's electron mobiliy, which is the speed at which electrons can move through each transistor. The problem of low carier mobility for the a-Si:H TFTs can be overcome by introducing polycrystalline silicon (poly-Si) thin film instead of a-Si:H as a semiconductor layer of TFTs. Therefore, poly-Si has gained increasing interest and has been investigated by many researchers. Recnetly, fabrication of such poly-Si TFT-LCD panels with VGA pixel size and monolithic drivers has been reported, . Especially, fabricating poly-Si TFTs at a temperature mach lower than the strain point of glass is needed in order to have high mobility TFTs on large-size glass substrate, and the monolithic drivers will reduce the cost of TFT-LCDs. The conventional methods to fabricate poly-Si films are low pressure chemical vapor deposition (LPCVD0 as well as solid phase crystallization (SPC), pulsed rapid thermal annealing(PRTA), and eximer laser annealing (ELA). However, these methods have some disadvantages such as high deposition temperature over $600^{\circ}C$, small grain size (<50nm), poor crystallinity, and high grain boundary states. Therefore the low temperature and large area processes using a cheap glass substrate are impossible because of high temperature process. In this study, therefore, we have deposited poly-Si thin films on si(100) and glass substrates at growth temperature of below 40$0^{\circ}C$ using newly developed high rate magnetron sputtering method. To improve the sputtering yield and the growth rate, a high power (10~30 W/cm2) sputtering source with unbalanced magnetron and Si ion extraction grid was designed and constructed based on the results of computer simulation. The maximum deposition rate could be reached to be 0.35$\mu$m/min due to a high ion bombardment. This is 5 times higher than that of conventional sputtering method, and the sputtering yield was also increased up to 80%. The best film was obtained on Si(100) using Si ion extraction grid under 9.0$\times$10-3Torr of working pressure and 11 W/cm2 of the target power density. The electron mobility of the poly-si film grown on Si(100) at 40$0^{\circ}C$ with ion extraction grid shows 96 cm2/V sec. During sputtering, moreover, the characteristics of si source were also analyzed with in situ Langmuir probe method and optical emission spectroscopy.