• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.337-338
• /
• 2009

A flexible photoluminescent display device was proposed and fabrication technology with a low process temperature was investigated in order to improve its reliability. The proposed flexible photoluminescent display showed good characteristics in reliability and flexibility. The lifetime of the proposed flexible photoluminescent displays with organics components is estimated to be approximately more than 10,000 hours.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.250-253
• /
• 2004

Emphasis has been placed on thin plate fabrication of plain woven carbon fabric reinforced Al matrix composites using liquid pressing process. The composite has potential applications for PDP rear plate. The process is to use the low pressure for infiltration of Al melt into plain woven carbon fabric as the Al melt is pressurized directly. The minimum pressure required for the infiltration was calculated from force balance equation, permeability measurements and compaction behavior of carbon fiber. Also, the melting temperature and the holding time have been optimized. In order to measure coefficient of thermal expansion (CTE) of the composites, the thermal strain measurement using strain gage was performed and the thermal conductivity of the composites was measured using laser flash method. The constituent materials of the composite are PAN type carbon fibers as reinforcements and 6061 Al alloys as matrices.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.134-137
• /
• 2002

A new LTCC material in the $PbWO_4-TiO_2-B_2O_3-CuO$ system was developed. The developed material can be sintered at $850^{\circ}C$ and its dielectric properties are $\varepsilon_r=20-25, Q\timesf_o=30000~50000GHz$ , and $\tau_f=0.2~30ppm/^{\circ}C$, depending on the components moi ratio. Due to its low sintering temperature and microwave dielectric properties, the developed material can be used as a LTCC substrate for fabrication of multilayered microwave communication module set. In present study, using this material, tape casting condition was established. With this processing condition, a T-resonator was fabricated and its electrical properties were examined. Also, a 2-Pole band pass filter was fabricated and its frequency characteristics were compared with simulation results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.445-446
• /
• 2005

This letter reports the fabrication of polycrystalline silicon thin-film transistors (poly-Si TFT) on flexible plastic substrates using amorphous silicon (a-Si) precursor films by sputter deposition. The a-Si films were deposited with mixture gas of argon and helium to minimize the argon incorporation into the film. The precursor films were then laser crystallized using XeCl excimer laser irradiation and a four-mask-processed poly-Si TFTs were fabricated with fully self-aligned top gate structure.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.115-119
• /
• 2001

For the fabrication of HTS power cable, multifilamentary Bi-2223/Ag tapes have been prepared using the powder-in-tube (PIT) process. After final heat treatment, these tapes have $I_{c}$ value of 43A, and$ J_{c}$ value of $28,000A/\textrm{cm}^2$(77K, 0T). Prototype 1000A class multistrand conductor(length~1m) was fabricated using these tapes(length~300m). This multistrand conductor was impregnated with low-temperature epoxy. The transportation properties of prototype 1000A class multistrand conductor has been evaluated at 77K, and yielding a current capacity up to 1200A.A.A.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.470-474
• /
• 2001

This paper describes the fabrication and characteristics of CrN thin-film type pressure sensors, in which the sensing elements were deposited on SuS. 630 diaphragm by DC reactive magnetron sputtering in an argon-nitride atmosphere(Ar-(10%)N$_2$). The optimized condition of CrN thin-film sensing elements was thickness range of 3500$\AA$ and annealing condition(300$\^{C}$, 3 hr) in Ar-10%N$_2$ deposition atmosphere. Under optimum conditions, the CrN thin-films for strain gauges is obtained a high resistivity, ρ=1147.65 $\mu$Ωcm, a low temperature coefficient of resistance, TCR=186ppm/$\^{C}$ and a high temporal stability with a good longitudinal, 11.17. The output sensitivity of fabricated CrN thin-film type pressure sensors is 2.36 mV/V, 4∼20nA and the maximum non-linearity is 0.4%FS and hysteresis is less than 0.2%FS.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.4
• /
• pp.336-341
• /
• 2008

Recently, research on a flat panel display(FPD) has focused on organic light-emitting display(OLED) which has wide angle of view, high contrast ratio and low power consumption. ITO(Indium-Tin-Oxide) films are the most widely used material as a transparent electrode of OLED and also in many other display devices like LCD or PDP. The performance and efficiency of OLED is related to the surface condition of ITO coated glass substrate. The typical surface defect of glass substrate is measured for electric characteristics and physical condition for transmittance and roughness. Since ITO coated glass substrate can be destroyed for inspection about surface roughness, sheet resistance, film thickness and transmittance, precise fabrication condition should be made based on the estimated relationship. In this paper, ITO films were prepared on the commercial glass substrate by the Ion-Plating method changing the partial pressure of gas(Ar, 02) and the chamber temperature between $200^{\circ}C$ and $300^{\circ}C$. The characteristics of films were examined by the 4-point probe, supersonic thickness measurement, transmittance measurement and AFM. We estimated the relationship between processing parameters(Ar gas, O2 gas, Temperature) and properties of ITO films (Sheet Resistance, Film Thickness, Transmittance, Surface Roughness).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.373-373
• /
• 2012

We fabricated conductive zinc oxide (ZnO) thin film at low temperature by UV-enhanced atomic layer deposition. The atomic layer deposition relies on alternate pulsing of the precursor gases onto the substrate surface and subsequent chemisorption of the precursors. In this experiment, diethylzinc (DEZ) and $H_2O$ were used as precursors with UV light. The UV light was very effective to improve the conductivity of the ZnO thin film. The thickness, transparency and resistivity were investigated by ellisometry, UV-visible spectroscopy and Four-point probe.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.387-390
• /
• 2004

Thick film alcohol gas sensors were fabricated. Their electrical properties and gas sensing characteristics were investigated. The sensitivity of $1wt.\%$ Pd-doped ${\gamma}-Fe_2O_3$ thick film heat treated at $400^{\circ}C$, 2hrs was $74\%$ to 500ppm alcohol gas at the operating temperature of $250^{\circ}C$. The selectivity of the film to alcohol was good. It showed fast response time to low concentrations of alcohol in air, hence this sensor can be used as a breath sensor.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2006.02a
• /
• pp.125-125
• /
• 2006