• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.5
• /
• pp.162-167
• /
• 2009

In this paper, we present a compact Ultra-Wideband band-pass filter using a high-pass filter and low-pass filter. The structure of our proposed band-pass filter is very simple and the DGS(Defected Ground Structure) structure is used to get the low-pass filter characteristic. Our proposed band-pass filter can be much smaller than a cascaded filter. As a result of measurement the insertion loss is less than 0.5dB throughout the pass-band of $2.1GHz{\sim}10.56GHz$, the return loss is more than 20dB and the group delay maximum variation is 0.23ns from 0.12ns to 0.35ns.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1015-1024
• /
• 2015

This paper introduces a low cost, high efficiency, high performance three-phase unified power quality conditioner (UPQC) by using four-switch three-phase inverters (FSTPIs) and an extra capacitor in the shunt active power filter (APF) side of the UPQC. In the proposed UPQC, both shunt and series APFs are developed by using FSTPIs so that the number of switching devices is reduced from twelve to eight devices. In addition, by inserting an additional capacitor in series with the shunt APF, the DC-link voltage in the proposed UPQC can also be greatly reduced. As a result, the system cost and power loss of the proposed UPQC is significantly minimized thanks to the use of a smaller number of power switches with a lower rating voltage without degrading the compensation performance of the UPQC. Design of passive components for the proposed UPQC to achieve a good performance is presented in detail. In addition, comparisons on power loss, overall system efficiency, compensation performance between the proposed UPQC and the traditional one are also determined in this paper. Simulation and experimental studies are performed to verify the validity of the proposed topology.

• Korean Management Science Review
• /
• v.32 no.3
• /
• pp.55-70
• /
• 2015

The main objective of this study is to investigate the moderating roles of the competitor's pricing strategy and the degree of consumer's risk-aversion on perceived risk and perceived benefit in responding to price increases and package downsizing. Based on Prospect Theory, several prior researches find that consumers perceive increased price as more loss than package downsizing and perceive package downsizing as more benefit than increased price. We extend these behavioral economics approach using the reference effect of competitor's pricing strategy. We focus on consumer heterogeneity on risk-aversion, measure the degree of consumer's risk-aversion, and divide the consumers into two groups of high levels of risk-aversion vs. low levels of risk-aversion. We find that the firm's pricing strategies of both price increases and package downsizing do not significantly influence the perceived benefit for relatively low risk-aversion consumers. We find that when the firm reduce the package size, relatively high risk-aversion consumers perceived more benefit and had higher purchase intention compared to price increases. We also find that the competitor's pricing strategies do not significantly influence the consumer's response for relatively low risk-aversion consumers. For relatively high risk-aversion consumers, they perceived more loss when the firm has different pricing strategy from the competitor's.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5A
• /
• pp.674-681
• /
• 2000

We proposed polymer based vertical asymmetric optical coupler. And we optimized the proposed device by coupling characteristic analysis In 1.33um wavelength, TE mode, we obtained very short coupling length(L=277.6um), high coupling efficiency(94%). The merits of proposed device are low propagation loss due to very short full device, low production cost and time, and high integrated fabrication. We will use this to fabricate optical switch, modulator and tunable WDM devices, etc.

• Journal of Communications and Networks
• /
• v.17 no.3
• /
• pp.286-295
• /
• 2015

Avionic databuses fulfill a critical function in the connection and communication of aircraft components and functions such as flight-control, navigation, and monitoring. Ethernet-based avionic databuses have become the mainstream for large aircraft owning to their advantages of full-duplex communication with high bandwidth, low latency, low packet-loss, and low cost. As a new generation aviation network communication standard, avionics full-duplex switched ethernet (AFDX) adopted concepts from the telecom standard, asynchronous transfer mode (ATM). In this technology, the switches are the key devices influencing the overall performance. This paper reviews the avionic databus with emphasis on the switch architecture classifications. Based on a comparison, analysis, and discussion of the different switch architectures, we propose a new avionic switch design based on a time-division switch fabric for high flexibility and scalability. This also merges the design concept of space-partition switch fabric to achieve reliability and predictability. The new switch architecture, called space partitioned shared memory switch (SPSMS), isolates the memory space for each output port. This can reduce the competition for resources and avoid conflicts, decrease the packet forwarding latency through the switch, and reduce the packet loss rate. A simulation of the architecture with optimized network engineering tools (OPNET) confirms the efficiency and significant performance improvement over a classic shared memory switch, in terms of overall packet latency, queuing delay, and queue size.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.25-31
• /
• 2014

This paper details application of a DLC(Diamond Like Carbon)-coating to the swash plate and the ball joint of pistons that make sliding contact with the piston shoes of an axial piston pump. This process, aimed to reduce the frictional and leakage power losses of the hydrostatic piston shoe bearings at the low speed range. At lower speeds than 100rpm, the positive effects of the DLC-coating on the power loss reduction of the hydrostatic piston shoe bearings could be confirmed. These effects resulted in little improvement in volumetric efficiency of the test pump, but the mechanical efficiency could be raised by up to 5% at 100rpm; here, the DLC-coated swash plate played a more dominant role than the DLC-coated ball joint.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.5
• /
• pp.299-304
• /
• 2018

An ideal circuit breaker should supply electric power to loads without losses in a conduction state and completely isolate the load from the power source by providing insulation strength in a break state. Fault current is relatively easy to break in an Alternating Current (AC) circuit breaker because the AC current becomes zero at every half cycle. However, fault current in DC circuit breaker (DCCB) should be reduced by generating a high arc voltage at the breaker contact point. Large fire may occur if the DCCB does not take sufficient arc voltage and allows the continuous flow of the arc fault current with high temperature. A semiconductor circuit breaker with a power electronic device has many advantages. These advantages include quick breaking time, lack of arc generation, and lower noise than mechanical circuit breakers. However, a large load capacity cannot be applied because of large conduction loss. An extinguishing technology of DCCB with polymeric positive temperature coefficient (PPTC) device is proposed and evaluated through experiments in this study to take advantage of low conduction loss of mechanical circuit breaker and arcless breaking characteristic of semiconductor devices.

• The KIPS Transactions:PartA
• /
• v.16A no.1
• /
• pp.27-34
• /
• 2009

Recently, power saving with high performance is one of the hot issues in the mobile systems. Various technologies are introduced to achieve low-power processors, which include sub-micron semiconductor fabrication, voltage scaling, speed scaling and etc. In this paper, we introduce a new method that reduces of energy loss at the data cache. Our methods take the benefits in terms of speed and energy loss using selective way precharging of way prediction with concurrent way selecting. By the simulation results, our method achieves 10.2% energy saving compared to the way prediction method, and 56.4% energy saving compared to the common data cache structure.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1148-1150
• /
• 2003

Power conversion system must be increased switching frequency in order to achieve a small size, a light weight and a low noise. However, the switches of converter are subjected to high switching power losses and switching stresses. As a result of those, the power system brings on a low efficiency. To improved these, a large number of soft switching topologies included a resonant circuit has been prosed. But these circuits increase number of switch in circuit and complicate sequence of switching operation. In this paper, the authors propose a high power factor and high efficiency DC-DC converter using single-pulse soft switching by partial resonant switching node. The switching devices in a prosed circuit are operated with soft switching by the partial resonant method, that is, Partial Resonant Switch Mode Power Converter. The partial resonant circuit makes use of a inductor using step up and a condenser of loss-less snubber. The result is that the switching loss is very low and the efficiency of system is high. Also the proposed converter is deemed the most suitable for high power applications where the power switching devices are used. Some simulative results on computer results are included to confirm the validity of the analytical results.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.520-524
• /
• 2001

Recently, the demand of large capacity SMPS for industrial area is increasing. Full-bridge dc-dc converter with IGBT is most widely used for large capacity SMPS because IGBT has a low-conduction loss and large current capacity, But most large capacity Full-bridge do-dc converter using IGBT has low operating frequency because of switching loss at IGBT especially at turn-off by current tail and it's cause of relatively big converter size. MOSFET has low switching losses has been widely used for high frequency SMPS but it has a problem to apply to large capacity SMPS because it has large conduction resistance causing large on-time losses. In this paper, for reduction losses at switching device, MOSFET is applied at parallel with IGBT in full-bridge dc/dc converter.