• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.207-210
• /
• 2000

Properties of SrTiO$_3$ thin films were characterized under the influence of an applied dc voltage utilizing a gold resonator with a flip-chip capacitor. The measurements were performed at microwave frequency ranges and low temperatures cryogenic temperatures. The dielectric constant of 830 and the low loss tangent of 6X10$^{-3}$ at 3.64 GHz were observed at 90 K and 100 V. The quality in the SrTiO$_3$ film was presented in terms of fractional frequency under the bias voltages and cryogenic temperatures.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1089-1095
• /
• 2005

This paper presents a new low-cost Built-In Self-Test (BIST) circuit for 50Hz low noise amplifier (LNA). The BIST circuit is designed for system-on-chip (SoC) transceiver environment. The proposed BIST circuit measures the LNA specifications such as input impedance, voltage gaih, noise figure, and input return loss all in a single SoC environment.

• Macromolecular Research
• /
• v.12 no.5
• /
• pp.474-477
• /
• 2004

We present simple, low-cost methods for the fabrication of polymeric waveguides that have large core sizes for use as optical interconnects. We have used both hot embossing and micro-contact printing techniques for the fabrication of multimode waveguides using the same materials. Rectangular and large-core (60${\times}$60 $\mu\textrm{m}$$^2$) channels were readily prepared when using these methods. The dimensions of the embossed and printed channels were the same as those of the pattern on the original master. The polymeric waveguides that we fabricated with large core sizes exhibited a low propagation loss of 0.1 dB/cm at 850 nm, which indicates that hot embossing and micro-contact printing are suitable techniques for the fabrication of optical waveguides having large-core.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3201-3204
• /
• 2000

In general, analog tester or strip chart recorder have been used to measure the corrosion potential of structures such as gas pipelines, oil pipelines, hot water pipelines, power cables etc. Recently, automatic digital data logger substitutes for these manual equipment because using these manual equipments are tedious and time consuming. However, digital data logger also has a shortcoming, that is, short measuring time because of the short lifetime of batteries. Therefore, we developed a long lifetime and low power loss battery taking advantage of galvanic series. In this paper, the results of development for power generator using two metals and DC/DC converter in order to obtain enough voltage for the operation of digital data logger. DC/DC converter operates with 0.5[V]. Its output voltage is 3.5[V] and output current is from 60[mAh] to 1,200[mAh].

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1413-1421
• /
• 2017

In order to control the output voltage in a dual active bridge converter, this paper establishes a theoretical inductor current equation for a dual-pulse-width-modulation scheme that ensures low switching loss. It also proposes a modulation strategy that minimizes conduction loss. When compared to the conventional single-pulse-width-modulation strategy, the proposed approach can reduce the inductor current RMS and improve efficiency in the low power region, as verified through simulation and experimental results.

• Journal of Korean Medicine for Obesity Research
• /
• v.2 no.1
• /
• pp.83-87
• /
• 2002

Increasing body weight is closely associated with increasing risk for glucose intolerance and type II diabetes. Especially, abdominal distribution of weight and visceral obesity also seriously increase the morbidity and mortality. Dietary program including very-low-calorie diet(VLCD) is regarded as most effective in the control of obesity and diabetes, which mainly due to calorie restriction rather than weight loss itself. We are reporting a case of diabetes with obesity whose fast glucose was over 220 mg/dl and BMI was $25.1kg/m^2$(fat rate 32.8%, WHR 0.9). She was prescribed VLCD and oriental medical diet program. After 10 days of hospitalization, her glucose level dropped dramatically with 3kg loss of body weight She has further lost her weight until about 53kg, but the glucose level ceased to go down probably due to loosened calorie restriction.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.12
• /
• pp.103-108
• /
• 2004

In this paper, we present MIMIC(Millimeter-wave Monolithic Integrated Circuit) up-mixer with low conversion loss and low LO power for the V-band transmitter applications. The up-mixer was successfully integrated by using 0.1 ㎛ GaAs pseudomorphic HEMTs(PHEMTs) and coplanar waveguide (CPW) structures. The circuit is designed to operate at RF frequencies of 60.4 GHz, IF frequencies of 2.4 GHz, and LO frequencies of 58 GHz. The fabricated MIMIC up-mixer size is 2.3 mmxl.6 mm. The measured results show that the low conversion loss of 1.25 dB when input signal is -10.25 dBm at LO power of 5.4 dBm. The LO to RF isolation is 13.2 dB at 58 GHz. The fabricated V-band up-mixer represents lower LO input power and conversion loss characteristics than previous reported millimeter-wave up-mixers.

• BMB Reports
• /
• v.47 no.9
• /
• pp.506-511
• /
• 2014

We investigated the effects of high calorie and low calorie diets on skeletal integrity, and whether ${\beta}$-adrenergic blockade (BB) attenuates bone loss induced by dietary calorie alteration. Male 6-week-old C57BL/6 mice were assigned to either an ad-lib fed control diet (CON), a high calorie diet (HIGH), or a low calorie diet (LOW) group. In each diet group, mice were treated with either vehicle (VEH) or propranolol, a ${\beta}$-adrenergic antagonist. Over 12-weeks, ${\beta}$-blockade mitigated body weight and fat mass increases induced by the high calorie diet. Femoral trabecular bone mineral density and the expression levels of osteogenic marker genes in bone marrow cells were reduced in HIGHVEH and LOWVEH mice, and BB significantly attenuated this decline only in HIGH mice. In summary, the magnitude of bone loss induced by low calorie diet was greater than that caused by high calorie diet in growing mice, and ${\beta}$-blockade mitigated high calorie diet-induced bone loss.

• Journal of Advanced Navigation Technology
• /
• v.21 no.6
• /
• pp.626-632
• /
• 2017

This paper describes a high power amplifier combining eight low power amplifiers using a radial power combiner with low insertion loss. The radial power combiner is a non-resonant type combiner with 8 input ports and is implemented by microstrip transmission line. The combiner characteristics designed at operating frequency of 1.045 GHz have an insertion loss of 0.7 dB and a return loss of more than 12 dB. Also, the low power amplifier used was designed with AFT27S010NT1 transistor and designed to satisfy the same gain, phase and constant output characteristic at operating frequency. The high power amplifier, which combiners the radial power combiner and the drive amplifier of 8 W output by driving low power amplifiers obtained the output characteristic of 33 W at operating frequency of 1.045 GHz. Also, the change of the output characteristic of the amplifier using the radial combiner was graceful degradation when the low power amplifier failed one by one.

• Journal of the Korean Society for Railway
• /
• v.19 no.2
• /
• pp.124-134
• /
• 2016

Research on low height noise barriers installed adjacent to railways to reduce the height of the noise barrier has actively progressed in many countries except Korea. The performance of low height noise barriers is evaluated to identify barrier acoustic characteristics using a scale model of the barrier in the present research. As shown in the experimental results, if it is considered the installation of 'ㄱ' type noise barrier, sound absorption material should be installed on both the top and the vertical surfaces of the barrier to improve insertion loss. Also, an analytical method such as the boundary element method, rather than a simple empirical equation, is required to evaluate the insertion loss of the barrier. In addition, noise level increase in passenger position is very small if a barrier with sound absorption material is installed. Finally, the two dimensional boundary element method is implemented to predict the acoustic characteristics of the low height barrier; the possibility of the application is confirmed from a comparison of the results of measurements and predictions.