• International journal of advanced smart convergence
• /
• 제9권2호
• /
• pp.105-113
• /
• 2020

In this paper, we proposed a soft switched synchronous boost converter, which can perform discharging the battery, is proposed. The proposed converter has low switching loss even at high frequency operation due to its soft switching characteristics. The converter operates in synchronous mode to minimize conduction loss because of changing the rectified diode to MOSFET with a low on resistance. In this reason, the efficiency of the converter can be greatly improved in high frequency. In this paper, the battery discharger with a switching frequency of 100 kHz, has been designed. The designed converter also simulated to prove the converter's characteristics of synchronous operation as well as soft switching operation. The simulation shows that the proposed converter always meets the soft switching conditions of turning on and off switching in the zero voltage and zero current states. Therefore, simulation results have confirmed that the proposed battery discharge had soft switching characteristics. The simulation results have confirmed that the proposed battery discharger had soft switching and synchronous operation characteristics.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.240-243
• /
• 2008

In this paper, the design of Centrifugal Compressor which is used in sizes 50 horse power has 8 pressure ratio and numerical analysis of the flow within compressor varying tip clearance length are performed. To get high pressure ratio with low power the exit height of impellers is low but compressor has very high speed of revolution. So compressor has high specific speed although mass flow rate is very small. The shape of impellers at the first stage is carried out. Flow and performance characteristics of impellers has been analyzed by using a commercial CFD program, $Fine^{TM}$/turbo. The result shows that loss coefficient is affected by tip clearance length and compressor has proper tip clearance length. It is possible to decrease loss by selecting apt tip clearance length.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.1166-1169
• /
• 2005

This paper describes a new transient voltage suppressor(TVS) with a low insertion loss and a high cut-off frequency to protect antenna circuit from transient voltages. Conventional protection devices have some problems such as a low frequency bandwidth and a high insertion loss. In order to improve these limitations, a coaxal type TVS, which consists of a gas tube is developed. The performance of the proposed transient voltage suppressor is tested by using a combination surge generator specified in IEC 61000-4-5 standard and by using a network analyzer of 40 MHz ${\sim}$ 5 GHz bandwidth. From the experimental results, it is confirmed that the proposed TVS has an enough protection performance in a low insertion loss and a high cut-off frequency.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2012년도 추계학술대회
• /
• pp.570-572
• /
• 2012

In this paper, a three-dimensional (3-D) low-loss and wide-band BPF based on low-temperature co-fired ceramic (LTCC) has been presented for mm-wave wireless communication applications. The proposed BPF is designed in a 6-layer LTCC substrate. The double patch resonators are fully integrated into the LTCC dielectrics and vertical via and planar CPW transitions are designed for interconnection between embedded resonators and in/output ports and MMICs, respectively. The designed BPF was fabricated in a 6-layer LTCC dielectric. The fabricated BPF shows a centre frequency (fc) of 53.23 GHz and a 3dB bandwidth of 14.01 % from 49.5 to 56.9 GHz (7.46 GHz). An insertion loss of -1.56 dB at fc and return losses below -10 dB are achieved. Its whole size is $4.7{\times}1.7{\times}0.684mm^3$.

• Journal of Welding and Joining
• /
• 제12권1호
• /
• pp.94-101
• /
• 1994

In this study, plasma spraying has been used to produce $TiO_2$ polycrystalline coatings from $TiO_2$ powders. The physical and chemical properties of plasma sprayed $TiO_2$ coatings depend greatly on plasma spraying conditions. The electrical resistivity, oxygen concentration, photocurrent and crystal structure of plasma sprayed $TiO_2$ coating has been studied. The results are as follows: 1. The oxygen loss and electrical conductivity of $TiO_2$ plasma sprayed coatings increased by low pressure and high amount of auxiliary gas, hydrogen in plasma spraying. 2. Oxygen loss increase electrical conductivity, and decrease photocurrent of $TiO_2$ plasma sprayed coatings. 3. Photocurrent of $TiO_2$ plasma sprayed coatings manufactured in atmospheric pressure is higher than that of low pressure.

• 한국컴퓨터정보학회논문지
• /
• 제21권1호
• /
• pp.79-84
• /
• 2016

In this paper, we propose reliable message transmission scheme based on CoAP, considering the constrained feature of IoT device, such as low power, the limited memory size and low computing capacity. Recently, the various kinds of application protocol has been studied to support IoT environments. In particular, CoAP protocol was developed as application protocol for IoT at the IETF core WG. However, because CoAP protocol is deigned to be used in constrained node, this protocol uses UDP at transport layer. Thus, data loss may occur frequently in network congestion environments. The proposed scheme, in this paper, is to overcome the problem of frequent data loss with low overhead. Also it includes the function which is to minimize the data loss in sleep mode of IoT device.

• 조명전기설비학회논문지
• /
• 제12권1호
• /
• pp.117-125
• /
• 1998

본 논문에서는 전류시 유도전동기의 누설 인덕턴스 및 직류 링크 인덕터에서 발생하는 손실과 스너버 회로에서 발생하는 손실을 효과적으로 전원 및 부하로 회생하는 새로운 VCC-3를 제안하였으며, VCC-1, VCC-2 및 VCC-3를 3상 유도전동기에 적용하여 부하의 입·출력 특성과 궤환량 등을 측정, 비교·검토한 결과, VCC-3 방식의 GTO CSI가 효율개선 및 안전성 면에서 우수하다는 것을 입증하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.577-595
• /
• 2017

${\bullet}$ Silicon Carbide (SiC) had excellent material properties as the base material for next generation of power semiconductor. In developing SiC MOSFET, gate oxide reliability issues had to be first overcome before commercial application. Besides, a high and stable gate-source voltage threshold $V_{GS(th)}$ is also an important parameter for operation robustness. SiC MOSFET with such characteristics can directly use existing high-speed IGBT gate driver IC's. ${\bullet}$ The linear voltage drop characteristics of SiC MOSFET will bring lower conduction loss averaged over full AC cycle compared to similarly rate IGBT. Lower switching loss enable higher switching frequency. Using package with auxiliary source terminal for gate driving will further reduce switching losses. Dynamic characteristics can fully controlled by simple gate resistors. ${\bullet}$ The low switching losses characteristics of SiC MOSFET can substantially reduce power losses in high switching frequency operation. Significant power loss reduction is also possible even at low switching frequency and low switching speed. in T-type 3-level topology, SiC MOSFET solution enable three times higher switching freqeuncy at same efficiency.

• 한국염색가공학회지
• /
• 제2권3호
• /
• pp.8-13
• /
• 1990

In order to study the modification of wettability, tactility, and bathochromicity of the poly (ethylene Terephthalate) (PET) fabrics, low-temperature plasma$(O_2)$ has been irradiated on the PET fabrics in various conditions. The results obtained from this study were as follows; 1) The weight loss rate of plasma-treated PET fabrics is proportional to irradiation time and internal gas temperature of treating chamber. Also, the effect of weight loss is remarkable at gas pressure ranging from 3 torr to 5 torr. 2) The bathochromic effect of PET fabrics treated with low-temperature plasma$(O_2)$ was improved.

• International Journal of Computer Science & Network Security
• /
• 제24권7호
• /
• pp.118-122
• /
• 2024

The dielectric material is a basic element which impacts considerably on a microstrip structure performances. This project demonstrates how filter performances such as gain, bandwidth, return loss and insertion loss change proportionally with substrate material variation. The RT/Duroid 5880 and the FR-4 are two dielectric materials proposed as substrates of a low pass microstrip filter. The design and simulation are done on ADS software. The transmission and reflection characteristics show that the RT/ Duroid 5880 as a dielectric substrate permits to obtain better performance as compared to the FR-4 substrate.