• 한국세라믹학회지
• /
• 제54권1호
• /
• pp.55-60
• /
• 2017

An anorthite-based traditional ceramic was developed by adding secondary flux materials to a mixture of kaolin and $CaCO_3$ in order to minimize the deformation during the sintering process. Three flux materials, feldspar, talc, and frit, were evaluated by comparison with two commercial chinaware bodies. Anorthite body with glass frit exhibited poor firing shrinkage. Poor mechanical properties (modulus of rupture, MOR < 30 MPa) was observed for the bodies with feldspar. Another anorthite body was formulated with wollastonite as a Ca source. The fired body showed a MOR of 81 MPa and a shrinkage rate of 6% when wollastonite was added up to 50%. In the XRD analysis, the phase ratio between anorthite and quartz was the highest in the specimen with 50% wollastonite addition. Homogeneous and relatively small closed pores were observed in the microstructural analysis. These results suggest that a ceramic body formulated with 50% kaolin and 50% wollastonite can be fired at $1200^{\circ}C$ with a 6% firing shrinkage rate, giving rise to minimal sintering deformation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1229-1232
• /
• 2005

We report the method of preventing the grey color of Bi based glass frits caused by reduction of $Bi_2O_3$. To prevent reduction of $Bi_2O_3$, we controlled the melting temperature. Low melting temperature reduces the reduction of $Bi_2O_3$ and that makes clarity transparent glass cullets. After firing, glass frits that melted at lower temperature showed better transparency. To prevent the browning, we used some additives like CuO, $CeO_2$, CoO and $TiO_2$. The colors of glass cullets were varied according to additives. After firing, dielectric layer contained additives showed better transparency than the one without additives. In the point of reaction between dielectric layer and Ag electrode, CuO was the most effective additive in preventing the yellowing.

• 대한치과기공학회지
• /
• 제29권2호
• /
• pp.119-128
• /
• 2007

Although there are many different ways that restorations can be made, it can be said that the biocompatibility of abutment and crown is very important in this experiment. When placed in the actual oral cavity, the differences were obvious. Compared to In-ceram Aluminium, the structure that is obtained after firing reveals a particularly homogeneous distribution of the crystal and glass phase. The In-ceram aluminium system had many problems, such as having weak tensile strength, and having low bonding strength due to the shrinking that occurs after firing. Because of the opaque finish of the metal frame, the two may look similar from the outside, but it is evident that there are differences between using a metal frame and In-ceram. VITA VM9 has been designed as a special ceramic featuring a fine structure or stabilized Zro2 substructures, and so the VITA VM9 excels in its light refraction and reflection behavior, which is similar to natural teeth. It also has outstanding chemical balance, which presents advantages such as considerably reduced accumulation of plaque on the ceramic surface.? This ultimately results in easier care and cleaning for the patient.

• 한국유체기계학회 논문집
• /
• 제15권6호
• /
• pp.18-24
• /
• 2012

This study simulated the operation of a steam injected gas turbine combined heat and power (CHP) system. A full off-design analysis was carried out to examine the change in the turbine blade temperature caused by steam injection. The prediction of turbine blade temperature was performed for the operating modes suggested in the previous study where the limitation of compressor surge margin reduction was analyzed in the steam injected gas turbine. It was found that both the fully injected and partially injected operations suggested in the previous study would cause the blade temperature to exceed that of the pure CHP operation and the under-firing operation would provide too low blade temperature. An optimal operation was proposed where both the turbine inlet temperature and the injection amount were modulated to keep both the reference turbine blade temperature and the minimum compressor surge margin. The modulation was intended to maintain a stable compressor operation and turbine life. It was shown that the optimal operation would provide a larger power output than the under-firing operation and a higher efficiency than the original partially injected operation.

• 한국연소학회지
• /
• 제20권1호
• /
• pp.15-23
• /
• 2015

This paper presents the results of field demonstration for fuel switching to bio-fuel oil in 4 commercial heavy oil fired power plants. The 100% fuel switching field demonstration was successfully carried out in two tangential-firing boilers at a capacity of 75 and 100 MWe respectively without major equipment retrofit, and also 25% bio-fuel oil blending for two opposite firing boilers at a capacity of 350 and 400 MWe respectively. Despite the low density and heating value, the bio fuel was successfully replaced heavy fuel oil at the full load by only adjusting operational parameters. Incase of bio fuel oil combustion, heat absorption of radiative heat transfer section was reduced while convection section has opposite trend. In pollutants emission, a major reductionin SOx as well as 10-20% reduction in NOx were achieved by the fuels witching. On the other hand, boiler efficiency was slightly underestimated.

• 대한전기학회논문지:전력기술부문A
• /
• 제50권12호
• /
• pp.561-567
• /
• 2001

This paper describes the application of Fuzzy Logic Controller (FLC) to Thyristor Controlled Series Capacitor (TCSC) which can have significant impact on power system dynamics. The function of the FLC is to control the firing angle of the TCSC. We tuned the scaling factors of the FLC using Tabu Search. The proposed FLC is used for damping the low frequency oscillations caused by disturbances such as the sudden changes of small or large loads or the outages in the generators or transmission lines. To evaluate usefulness of the proposed FLC, we performed the computer simulation fur single-machine infinite system. The response of FLC is compared with that of PD controller optimized using Tabu Search. Simulation results that the FLC shows better control performance than PD controller.

• 보존과학연구
• /
• 통권23호
• /
• pp.5-39
• /
• 2002

The scientific analysis and provenance study of potteries excavated from kiln sites at Jeonla Nam. Buk-do were carried out using XRD,ICP-AES and NAA. We can summarize the following consequence. First, as a result of XRD analysis, it showed that soft potteries consist of quartz, feldspar and clay minerals while hard potteries consist of high temperature crystals such as mullite, tridymite, cristobalite. In case of firing temperature which are determined by crystals using XRD, potteries are composed of quartz, feldspar and clay minerals had very low firing temperature. While potteries having only cristobalite ranged above$1200^{\circ}C$. Second, as a result of correlation analysis using trace element, the selected characteristic elements which was able to distinguish from each kiln site was Ce, Lu, Cs, Sc, Eu. Third, discriminant analytical results showed that kiln site of the Jeonla Namdo were classified into five groups and that of the Jeolna Buk-do into three groups. This suggests that there are no correlations between the raw materials used in each kiln sites.

• 한국연소학회지
• /
• 제20권2호
• /
• pp.40-45
• /
• 2015

This study is aimed to study combustion characteristics of low $NO_X$ burner using petroleum cokes as fuel. The petroleum coke, which is produced through the oil refining process, is an attractive fuel in terms of its high heating value and relatively low price. But petroleum coke is a challenging fuel because of its low volatile content, high sulfur and nitrogen content, which give rise to undesirable emission characteristics and low ignitability. The petroleum cokes burner is operated at fuel rich condition, and overfire air are supplied to achieve fuel lean condition. The low $NO_X$ burner is designed to control fuel and air mixing to achieve air staged combustion, in addition secondary and tertiary air are supplied through swirler. Air distribution ratio of triple staged air are optimized experimentally. The result showed that $NO_X$ concentration is lowest when overfire air is used, and the burner function at a fuel rich condition.

• 한국추진공학회지
• /
• 제20권1호
• /
• pp.69-75
• /
• 2016

본 논문은 한국형발사체 연소기 연소시험설비의 구축과 시운전 결과를 다루고 있다. 이 시험설비는 2012년부터 2014년까지 구축되었고, 2014년 하반기에 시운전이 수행되었다. 시운전 과정에는 산화제 수류시험, 연료 수류시험, 냉각수 수류시험 등이 수행되었고, 이후 점화시험이 이루어졌다. 점화시험 결과는 연소기의 시동시퀀스를 설정하는데 적용되며, 저압연소시험과 설계점 연소시험을 위한 기초자료로 활용되게 된다.

• 자원환경지질
• /
• 제53권3호
• /
• pp.307-320
• /
• 2020

이 연구에서는 중요한 수중발굴지의 하나인 충남 태안 마도해역에서 출수된 도자기를 대상으로 물리적, 광물학적 및 지구화학적 특성을 분석하여 태토의 동질성과 소성온도를 검토하였다. 연구대상 도자기는 청자, 분청사기 및 백자로 다양하나 전반적으로 거의 유사한 물리적 특성을 보인다. 모든 도자기의 태토에서 뮬라이트와 석영이 주요 광물로 확인되며, 일부 백자에서만 크리스토발라이트가 동정되었다. 또한 청자와 분청사기 태토는 동질한 조성과 점토화도 및 원소의 거동양상을 보이는 반면, 백자는 이와 상이하며 미량 및 불호정원소를 중심으로 다양한 특징을 보인다. 따라서 백자는 청자 및 분청사기 제작에 사용한 태토와 성인이 다른 점토로 제작되었으며, 이 중에서도 낮은 Th 함량을 갖는 일부 백자는 또다른 상이한 환경에서 형성된 점토를 활용한 것으로 추정된다. 한편 도자기의 소성온도는 대부분 1,200에서 1,300℃로 보이며 일부 청자는 1,150℃에서 1,200℃, 일부 백자는 1,500℃ 정도의 과소성을 경험하였을 가능성이 있는 것으로 해석된다.