Journal of the Korean Ceramic Society (한국세라믹학회지)

The Korean Ceramic Society (한국세라믹학회)
권호 표지
DOI QR코드

DOI QR Code

Development and Characteristics of Anorthite-Based Traditional Ceramic Materials to Suppress Sintering Deformation

  • Choi, JungHoon (Department of Materials Engineering, Gyeongsang National University) ;
  • Kim, UngSoo (Ceramicware Center, Korea Institute of Ceramic Engineering and Technology) ;
  • Cho, WooSeok (Ceramicware Center, Korea Institute of Ceramic Engineering and Technology)
  • Received : 2016.09.29
  • Accepted : 2017.01.16
  • Published : 2017.01.31
Download PDF
⟨ Previous Next ⟩

Abstract

An anorthite-based traditional ceramic was developed by adding secondary flux materials to a mixture of kaolin and $CaCO_3$ in order to minimize the deformation during the sintering process. Three flux materials, feldspar, talc, and frit, were evaluated by comparison with two commercial chinaware bodies. Anorthite body with glass frit exhibited poor firing shrinkage. Poor mechanical properties (modulus of rupture, MOR < 30 MPa) was observed for the bodies with feldspar. Another anorthite body was formulated with wollastonite as a Ca source. The fired body showed a MOR of 81 MPa and a shrinkage rate of 6% when wollastonite was added up to 50%. In the XRD analysis, the phase ratio between anorthite and quartz was the highest in the specimen with 50% wollastonite addition. Homogeneous and relatively small closed pores were observed in the microstructural analysis. These results suggest that a ceramic body formulated with 50% kaolin and 50% wollastonite can be fired at $1200^{\circ}C$ with a 6% firing shrinkage rate, giving rise to minimal sintering deformation.

Keywords

References

  1. J. S. Moon, Engineering of Pottery; pp.184-92, DooYangSa, Seoul, 2003.
  2. J. G. Lee, Sintering of Ceramics; pp.138-46, Bando publisher, Seoul, 1991.
  3. S. Kurama and E. Ozel, "The Influence of Different CaO Source in the Production of Anorthite Ceramics," Ceram. Int., 35 [2] 827-30 (2009). https://doi.org/10.1016/j.ceramint.2008.02.024
  4. Y. Kobayashi and E. Kato, "Low-Temperature Fabrication of Anorthite Ceramics," J. Am. Ceram. Soc., 77 [3] 833-34 (1994). https://doi.org/10.1111/j.1151-2916.1994.tb05373.x
  5. V. M. F. Marques, D. U. Tulyaganov, S. Agathopoulos, V. K. Gataullin, G. P. Kothiyal, J. M. F. Ferreira, "Low Temperature Synthesis of Anorthite Based Glass-Ceramics via Sintering and Crystallization of Glass-Powder Compacts," J. Eur. Ceram. Soc., 26 [13] 2503-10 (2006). https://doi.org/10.1016/j.jeurceramsoc.2005.07.055
  6. Y. G. Jung, "Effect of Firing Temperature on Mechanical Property and Contact Damage in Pottery (in Korean)," J. Korean Ceram. Soc., 35 [12] 1343-50 (1998).
  7. M. U. Taskiran, N. Demirkol, and A. Capoglu, "A New Porcelainised Stoneware Material Based on Anorthite," J. Eur. Ceram. Soc., 25 [4] 293-300 (2005). https://doi.org/10.1016/j.jeurceramsoc.2004.03.017
  8. S. Wang, X. Q, J. Hu, and X. Tian, "Characterization of Anorthite-Based Porcelain Prepared by Using Wollastonite as a Calcium Source," J. Ceram. Process. Res., 16 [3] 361-65 (2015).
  9. M. U. Taskiran, N. Demirkol, and A. Capoglu, "Influence of Mixing/Milling on Sintering and Technological Properties of Anorthite Based Porcelainised Stoneware," Ceram. Int., 32 [3] 325-30 (2006). https://doi.org/10.1016/j.ceramint.2005.03.010
  10. W.-P. Tai, K. Kimura, and K. Jinnai, "A New Approach to Anorthite Porcelain Bodies Using Nonplastic Raw Materials," J. Eur. Ceram. Soc., 22 [4] 463-70 (2002). https://doi.org/10.1016/S0955-2219(01)00317-X