• 한국전기전자재료학회논문지
• /
• 제30권12호
• /
• pp.806-811
• /
• 2017

An all-transparent ultraviolet (UV) photodetector was fabricated by structuring $p-NiO/n-SnO_2/ITO$ on a glass substrate. $SnO_2$ is an important semiconductor material because of its large bandgap, high electron mobility, high transmittance (as high as 80% in the visible range), and high stability under UV light. For these reasons, $SnO_2$ is suitable for a range of applications that involve UV light. In order to form a highly transparent p-n junction for UV detection, $SnO_2$ was deposited onto a device containing NiO as a high-transparent metal conductive oxide for UV detection. We demonstrated that all-transparent UV photodetectors based on $SnO_2$ could provide a definitive photocurrent density of $4nA\;cm^{-2}$ at 0 V under UV light (365 nm) and a low saturation current density of $2.02nA{\times}cm^{-2}$. The device under UV light displayed fast photoresponse with times of 31.69 ms (rise-time) and 35.12 ms (fall-time) and a remarkable photoresponse ratio of 69.37. We analyzed the optical and electrical properties of the $NiO/SnO_2$ device. We demonstrated that the excellent properties of $SnO_2$ are valuable in transparent photoelectric device applications, which can suggest various routes for improving the performance of such devices.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.471.2-471.2
• /
• 2014

We demonstrate here that an improvement in precursor film density (green density) leads to a great enhancement in the photovoltaic performance of CuInSe2 (CISe) thin film solar cells fabricated with Cu-In nanoparticle precursor films via chemical solution deposition. A cold-isostatic pressing (CIP) technique was applied to uniformly compress the precursor film over the entire surface (measuring 3~4 cm2) and was found to increase its relative density (particle packing density) by ca. 20%, which resulted in an appreciable improvement in the microstructural features of the sintered CISe film in terms of lower porosity, reduced grain boundaries, and a more uniform surface morphology. The low-bandgap (Eg=1.0 eV) CISe PV devices with the CIP-treated film exhibited greatly enhanced open-circuit voltage (VOC, from 0.265 V to 0.413 V) and fill factor (FF, from 0.34 to 0.55), as compared to the control devices. As a consequence, an almost 3-fold increase in the average power conversion efficiency, 3.0 to 8.2% (with the highest value of 9.02%), was realized without an anti-reflection coating. A diode analysis revealed that the enhanced VOC and FF were essentially attributed to the reduced reverse saturation current density (j0) and diode ideality factor (n). This is associated with the suppressed recombination, likely due to the reduction in recombination sites such as grain/air surfaces (pores), inter-granular interfaces, and defective CISe/CdS junctions in the CIP-treated device. From the temperature dependences of VOC, it was confirmed that the CIP-treated devices suffer less from interface recombination.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.356.1-356.1
• /
• 2014

The Isolation of few-layered transition metal dichalcogenides has mainly been performed by mechanical and chemical exfoliation with very low yields. in particular, the two-dimensional layer of molybdenum disulfide (MoS2) has recently attracted much interest due to its direct-gap property and potential application in optoelectronics and energy harvesting. However, the synthetic approach to obtain high-quality and large-area MoS2 atomic thin layers is still rare. In this account, a controlled thermal reduction-sulfurization method is used to synthesize large-MoOx thin films are first deposited on Si/SiO2 substrates, which are then sulfurized (under vacuum) at high temperatures. Samples with different thicknesses have been analyzed by Raman spectroscopy and TEM, and their photoluminescence properties have been evaluated. We demonstrated the presence of mono-, bi-, and few-layered MoS2 on as-grown samples. It is well known that the electronic structure of these materials is very sensitive to the number of layer, ranging from indirect band gap semiconductor in the bulk phase to direct band gap semiconductor in monolayers. This synthetic approach is simple, scalable, and applicable to other transition metal dichalcogenides. Meanwhile, the obtained MoS2 films are transferable to arbitrary substrates, providing great opportunities to make layered composites by stacking various atomically thin layers.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2012년도 추계학술대회
• /
• pp.838-841
• /
• 2012

본 논문에서는 온도변화에 따른 회로 손상이나 성능 저하를 피하기 위해서 회로 안에 내장할 수 있는 온도 센서 회로를 설계하였다. 일반적인 PTAT회로를 사용하여 온도감지를 하고, 스위치를 내장시켜 회로 동작이 불가능할 정도로 IC 내부 온도가 높을 때는 절전모드로 동작하게 하였다. 또한, 전류미러 및 캐스코드회로를 사용함으로서 전류 정합특성을 향상시켰다. 시뮬레이션 결과 $75^{\circ}C$일 경우 약 1V, $130^{\circ}C$일 경우 1.75V를 출력전압을 발생하였으며, 절전모드의 경우 0V~7uV까지 즉 거의 0V에 가까운 출력전압을 발생함을 확인 할 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.382-382
• /
• 2012

CIGS thin films have received great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films are deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. The deposition technique is one of the most important processes in preparing CIGS thin film solar cells. Among these methods, co-evaporation is one of the best technique for obtaining high quality and stoichiometric CIGS films. However, co-evaporation method is known to be unsuitable for commercialization. The sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have prepared by rf magnetron sputtering using a $Cu(In_{1-x}Ga_x)Se_2$ single quaternary target without post deposition selenization. This process has been examined by the effects of deposition parameters on the structural and compositional properties of the films. In addition, we will explore the influences of substrate temperature and additional annealing treatment after deposition on the characteristics of CIGS thin films. The thickness of CIGS films will be measured by Tencor-P1 profiler. The crystalline properties and surface morphology of the films will be analyzed using X-ray diffraction and scanning electron microscopy, respectively. The optical properties of the films will be determined by UV-Visible spectroscopy. Electrical properties of the films will be measured using van der Pauw geometry and Hall effect measurement at room temperature using indium ohmic contacts.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.162-162
• /
• 2011

Nanometer-sized noble metals can trap and guide sunlight for enhanced absorption of light based on surface plasmon that is beneficial for generation of hot electron flows. A pulse of high kinetic energy electrons (1-3 eV), or hot electrons, in metals can be generated after surface exposure to external energy, such as in the absorption of light or in exothermic chemical processes. These energetic electrons are not at thermal equilibrium with the metal atoms. It is highly probable that the correlation between hot electron generation and surface plasmon can offer a new guide for energy conversion systems [1-3]. We show that hot electron flow is generated on the modified gold thin film (<10 nm) of metal-semiconductor (TiO2) Schottky diodes by photon absorption, which is amplified by localized surface plasmon resonance. The short-circuit photocurrent obtained with low energy photons (lower than bandgap of TiO2, ~3.1-3.2 eV) is consistent with Fowler's law, confirming the presence of hot electron flows. The morphology of the metal thin film was modified to a connected gold island structure after heating to 120, 160, 200, and 240$^{\circ}C$. These connected island structures exhibit both a significant increase in hot electron flow and a localized surface plasmon with the peak energy at 550-570 nm, which was separately characterized with UV-Vis [4]. The result indicates a strong correlation between the hot electron flow and localized surface plasmon resonance with possible application in hot electron based solar cells and photodetectors.

• Current Photovoltaic Research
• /
• 제2권3호
• /
• pp.88-94
• /
• 2014

The structural, optical and electrical properties of sputter-deposited CIGS films were directly influenced by the sputtering process parameters such as substrate temperature, working pressure, RF power and distance between target and substrate. CIGS thin films deposited by using a quaternary target revealed to be Se deficient due to Se low vapor pressure. This Se deficiency affected the overall stoichiometry of the films, causing the films to be Cu-rich. Current tends to pass through the Cu-Se channels which act as the shunting path increasing the film conductivity. The crystal structure of CIGS thin films depends on the substrate orientation due to the influence of surface morphology, grain size and stress of Mo substrate. The excess of Cu was removed from the CIGS films by KCN treatment, achieving a suitable Cu concentration (referred as Cu-poor) for the fabrication of solar cell. Due to high Cu concentrations on the CIGS film surface induced by Cu-Se phases after CIGS film deposition, KCN treatment proved to be necessary for the fabrication of high efficiency solar cells. Also during KCN treatment, dislocation density and lattice parameter decreased as excess Cu was removed, resulting in increase of bandgap and the decrease of conductivity of CIGS films. It was revealed that Cu-Se secondary phase could be removed by KCN wet etching of CIGS films, allowing the fabrication of high efficiency absorber layer.

• 한국정보통신학회논문지
• /
• 제20권11호
• /
• pp.2085-2092
• /
• 2016

IC 기판의 가장 중요한 성질들의 하나는 넓은 영역에 걸쳐 균일해야만 한다는 것이다. 웨이퍼 결함 분석의 다양한 물리적 접근 방법 중에서 적외선 조사 기법에 특별한 관심이 모아지고 있다. 특히, 높은 공간적 분해력을 가지고 있는 근적외선 흡수 방법은 반-절연 GaAs 내의 결함들을 직접적으로 관찰하는데 이용되고 있다. 적외선 전송에 기초를 둔 이 기법은 신속하고 비파괴 적이다. 이 방법은, 직접적으로 GaAs 반도체의 적외선 영상은 결함의 광흡수 작용에 기인한 것임을 밝히고 있다. 반-절연 GaAs 내의 EL2에 관련된, 비 균일 적으로 분포된 결함들의 적외선 흡수 영상에서 콘트라스트가 반전되는 현상에 대해 새로운 모델을 제시하고 있다. 저온 포토퀀칭 실험은, 직접적인 방법으로, GaAs 웨이퍼의 콘트라스트 반전 영상은 밴드갭의 지엽적인 변동이나 전하 재분포에 의한 것이 아니라 흡수와 산란의 두 메커니즘에 의한 것임을 증명하고 있다.

• 한국전기전자재료학회논문지
• /
• 제22권10호
• /
• pp.814-820
• /
• 2009

Antimony (Sb) doped ZnO thin films (0.1 at.%) were deposited on sapphire (0001) substrates at various temperatures (200 - 600$^{\circ}C$) by using pulsed laser deposition technique. All the thin films have been characterized by X-ray diffractometer, atomic force microscopy and spectrophotometer to investigate their structural, morphological and optical properties, respectively. Hall measurements were also carried out to identify the electrical properties of the thin films. These thin films were constituted in wurtzite structure with the preferential orientation of (002) diffraction plane and had as high as 80% optical transmission in the visible range. The bandgap energy also was determined by spectrophotometer which was around 3.28 eV. Hall measurements results revealed that the Sb dope ZnO thin film (0.1 at.%) grown at $500^{\circ}C$ exhibited p-type conduction with a carrier concentration of $8.633\times10^{16}\;cm^{-3}$, a mobility of $1.41\;cm^2/V{\cdot}s$ and a resistivity of $51.8\;\Omega{\cdot}cm$. We have successfully achieved p-type conduction in antimony doped ZnO thin films with low doping level even though the electrical properties are not favorable. This paper suggests the feasibility of p-type doping with large-size-mismatched dopant by using pulsed laser deposition.

• 반도체디스플레이기술학회지
• /
• 제16권2호
• /
• pp.94-97
• /
• 2017

Amorphous Si has been used for data processing circuits in flat panel displays. However, low mobility of the amorphous Si is a limiting factor for the data transmission speed. Metal oxides such as ZnO have been studied to replace the amorphous Si. ZnO is a wide bandgap (3.3 eV) semiconductor with high mobility and good optical transparency. When ZnO is grown by sputtering with $O_2$ as an oxidizer, there can be many ion species arising from $O_2$ decomposition. $O^+$, $O_2{^+}$, and $O^-$ ions are expected to be the most abundant species, and it is not clear which one contributes to the ZnO growth. We applied alternating substrate voltage (0 V and -70 V) during sputtering growth. We studied changes in transistor characteristics induced by the voltage switching. We also compared ZnO grown by dc and rf sputtering. ZnO film was grown at $450^{\circ}C$ substrate temperature. ZnO thin-film transistor grown with these methods showed $7.5cm^2/Vsec$ mobility, $10^6$ on-off ratio, and -2 V threshold voltage.