• Composites Research
• /
• v.14 no.2
• /
• pp.22-32
• /
• 2001

Damage induced by low-velocity impact on the curved composite laminates was experimentally evaluated for CFRP cylindrical shells with the radius of curvatures of 50, 150, 300, and 500 mm. The result was then compared with that of flat laminates and with the results by nonlinear finite-element analysis. The radius of curvatures and the effective shell stiffness appeared to considerably affect the dynamic impact response of curved shells. Under the same impact energy level, the maximum contact force increased with the decreasing radius of curvatures, with reaching 1.5 times that for plates at the radius of curvature of 50 mm. Since the maximum contact farce is directly related to the impact damage, curved laminates can be more susceptible to delamination and less resistant to the low-velocity impact damage. Delamination was distributed rather evenly at each interface along the thickness direction of curved laminates on the contrary to the case of flat laminates, where delamination is typically concentrated at the interfaces away from the impact point. This implies that the effect of curvatures has to be considered for the design of a curved composite laminate.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.183-192
• /
• 2011

The demand for weight saving and high performance of aircraft require the more uses of composite materials. However the complicate behaviors and various failure characteristics restrict usage of composite materials. Low-velocity impact damage is a major concern in the design of structures made of composite materials, because impact damage is hidden and cannot be detected by visual inspection. Especially, the reduction on compressive strength after impact is influenced by the ply delaminations introduced as damage by impact event. In this research, the numerical analysis was performed to investigate impact damage and compressive strength after impact. It was found that impact force history and compressive strength after impact calculated by the numerical analysis were compared and shown a good agreement with experimental results.

• Journal of Korean Association for Spatial Structures
• /
• v.10 no.4
• /
• pp.75-83
• /
• 2010

Laminated composite plates have shown their superiority over metals in applications requiring high specific strength, high specific modulus, and so on. Therefore, they have used in various industry. However, they have poor resistance to impact compared to typical metal materials. So, many researchers have investigated about impact behavior of laminated composite plate. To investigate impact behavior of laminated composite plate, we have to calculate contact force between impactor and laminated composite plate at the first. Impactor's equation of motion, plate's equation of motion and correlations for indentation were solved to know the contact force at the same time. In this study, low velocity impact behavior of composite plate was investigated using the finite element program which is involved the classical Hertzian law, Sun's law and Sun & Yang's experimental law and Sun & Tan's experimental law considering the stacking method.

• Journal of the Korean Society of Safety
• /
• v.20 no.4 s.72
• /
• pp.14-19
• /
• 2005

One area in which composites have been used rather extensively is for fabricating pressure vessel. These structures can be readily manufactured by filament winding, which is, as far as composite fabrication techniques are concerned, a relatively inexpensive method for producing composite structures. Unfortunately, the higher strength material and fabrication costs are not the only disadvantages of fiber-reinforced polymer composites when they are compared to metals. Additionally, these materials tend to exhibit brittle behavior. This is of particular concern when they are subjected to a low-velocity impact during routine handling a significant amount of structural damage can be introduced into the composites. The goals of this paper are to understand the impact damage behavior and identify the effect of surface coating materials on impact resistance in filament wound composite pressure vessels. For these, a series of low velocity impact tests was performed on specimens cutting from the full scale pressure vessel by the instrumented impact testing machine. The specimens are classified into two types with and without surface protective material. The visualization for impact damage is made by metallurgical microscope. Based on the impact force history and damage, the resistance parameters were employed and its validity in identifying the damage resistance of pressure vessel was reviewed. As the results, the impact resistance of the filament wound composites and its dependency on the protective material were evaluated quantitatively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.11
• /
• pp.1080-1088
• /
• 2009

An actuator using piezoceramic material was designed in order to perform a flow control for flat plate flow. Boundary layer measurements were carried out to explore the flow disturbances by the designed actuator that was activated at low excitation frequency(15Hz). The mean velocity and fluctuation in the boundary layers were measured at $x/{\delta}^*=31.9$ downstream from the actuator tip by a one-dimensional hot-wire probe(55P14). Results reveal that low- and high-velocity regions were observed in the vicinity of the actuator center and in the outer area of the actuator respectively, and the formation of counter-rotating streamwise vortices was predicted. The fluctuations were persistently found in the outer part of the actuator and an inflection point in the spanwise gradient of the streamwise velocity was observed. Boundary layer instability was amplified at both the actuator excitation frequency and the T-S wave frequency when the actuator was excited at low frequency.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.47-53
• /
• 2015

This paper is to study applying for numerical analysis method for flow field, velocity and pressure of fuel on the low pressure pump using excavator. The pressure distribution of fuel pump certified the linear variation according to rotation angle of rotor. Especially, it knew the fact that the pressure in rotation angle $40^{\circ}$ appeared high outlet and low inlet of fuel pump. Also, this range angle can seek the fact that the leakage flow and velocity are the most increasing. And the more rotor rotation of fuel pump, the more mean outlet flow rate increased in linear. Whenever the gap size decrease with rotor and housing, the discharge flow rate could seek the approaching 0.0712kg/s that consider with theory discharge flow rate calculated from displacement between rotor gear and idle gear.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.5
• /
• pp.294-304
• /
• 2019

This study evaluates the variation characteristics of wave fields (transmission ratio, wave height, time-averaged velocity and time-averaged turbulent kinetic energy) for two-dimensional low-crested structure by olaFlow model based on the two-phases flow numerically. In addition, the present numerical results are verified by comparing with the existing experimental results. The time-averaged velocity, one of various numerical results is formed counterclockwise circulating cell on the front of structure and is occurred strong uni-directional flow on onshore side. It is shown that these are closely related to the factors such as overtopping, etc.

• Physical Therapy Rehabilitation Science
• /
• v.8 no.3
• /
• pp.125-133
• /
• 2019

Objective: To compare the postural control between non-specific chronic low back pain (NSCLBP) subgroups and healthy people during dynamic balance performance using a modified Star Excursion Balance Test (mSEBT). Design: Cross-sectional study. Methods: Eighteen NSCLBP subjects (9 active extension pattern [AEP], 9 flexion pattern [FP]), and 10 healthy controls were enrolled in this study. All subjects performed mSEBT on their dominant leg on a force plate. Normalized reach distance and balance parameters, including the center of pressure (COP) displacement and velocity, were recorded. Results: There were significant differences in mean reach distances in both posterolateral and posteromedial (PM) reach directions between AEP and healthy subjects (p<0.001) and between FP and healthy subjects (p<0.001). However, there were no significant differences among the three groups in the anterior reach direction. Also, the results showed no significant differences in mean COP variables (velocity and displacement) between pooled NSCLBP and healthy subjects. However, the subjects were reclassified into AEP, FP and healthy groups and the results showed a significant difference in mean COP velocity in the PM direction between AEP and FP subjects (p=0.048), and between AEP and healthy subjects (p=0.024). Conclusions: The findings in this study highlight the heterogeneity of the individuals with NSCLBP and the importance of identifying the homogenous subgroups. Individuals with AEP and FP experience deficits in dynamic postural control compared to healthy controls. In addition, the findings of this study support the concept of the Multidimensional Classification System.

• Composites Research
• /
• v.35 no.6
• /
• pp.469-476
• /
• 2022

In this paper, the microwave absorbing characteristics after the impact of the radar-absorbing structure (RAS) consisting of periodic pattern sheet (PPS) and glass fiber-reinforced plastic (GFRP) were experimentally investigated. The fabricated RAS effectively absorbed the microwave in the X-band (8.2-12.4 GHz). In order to induce the damage to the RAS, a low-velocity impact test with various impact energy of 15, 40, and 60 J was conducted. Afterward, the impact damage was observed by using visual inspection, non-destructive test, and image processing method. Moreover, the absorbing performance of intact and damaged RAS was measured by the free-space measurement system. The experiment results revealed that the delamination damage from the impact energy of 15 J did not considerably affect the microwave absorbing performance of the RAS. However, fiber breakage and penetration damage with a relatively large damaged area were occuured when the impact energy was increased up to 40 J and 60 J, and these failures significantly degraded the microwave absorbing characteristics of the RAS.

• Steel and Composite Structures
• /
• v.48 no.3
• /
• pp.305-320
• /
• 2023

The mechanical properties of polymeric composites are degraded under elevated temperatures due to the effect of temperature on the mechanical behavior of the resin and resin fiber interfaces. In this study, the effect of temperature on the impact response of the carbon fiber reinforced plastics (CFRP) was investigated at low-velocity impact (LVI) using a drop-weight impact tester machine. All the composite plates were fabricated using a vacuum infusion process with a stacking sequence of [45/0_2/-45/90_2]s, and a thickness of 2.9 mm. A group of the specimens was exposed to an environment with a temperature cycling at the range of -30 ℃ to 65 ℃. In addition, three other groups of the specimens were aged at ambient (28 ℃), -30 ℃, and 65 ℃ for ten days. Then all the conditioned specimens were subjected to LVI at three energy levels of 10, 15, and 20 J. To assess the behavior of the damaged composite plates, the force-time, force-displacement, and energy-time diagrams were analyzed at all temperatures. Finally, radiography, optical microscopy, and scanning electron microscopy (SEM) were used to evaluate the effect of the temperature and damages at various impact levels. Based on the results, different energy levels have a similar effect on the LVI behavior of the samples at various temperatures. Delamination, matrix cracking, and fiber failure were the main damage modes. Compared to the samples tested at room temperature, the reduction of temperature to -30 ℃ enhanced the maximum impact force and flexural stiffness while decreasing the absorbed energy and the failure surface area. The temperature increasing to 65 ℃ increased the maximum impact force and flexural stiffness while decreasing the absorbed energy and the failure surface area. Applying 200 thermal cycles at the range of -30 ℃ to 65 ℃ led to the formation of fine cracks in the matrix while decreasing the absorbed energy. The maximum contact force is recorded under cyclic temperature as 5.95, 6.51 and 7.14 kN, under impact energy of 10, 15 and 20 J, respectively. As well as, the minimum contact force belongs to the room temperature condition and is reported as 3.93, 4.94 and 5.71 kN, under impact energy of 10, 15 and 20 J, respectively.