• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.11
• /
• pp.1582-1590
• /
• 1998

Combustion-driven oscillations in a surface burner have been investigated to clarify their characteristics. A model combustor is made and the oscillation frequencies are measured for various dimensions of the combustor. It is found that there are two modes of oscillations; one is the 'acoustic mode' at high frequencies, associated with the acoustic mode of the combustion system and the other is the 'combustion mode' at low frequencies around 100 Hz, associated with the instability of the flame. Acoustic mode is excited when the surface burner is placed where the phase of particle velocity leads that of acoustic pressure by $90^{\circ}$, for all the combustion conditions. Combustion mode is driven at high combustion rate by the lift of unstable flame near the lower limit of the combustible equivalence ratio. Combustion mode is greatly influenced by the inlet temperature of the premixed gas. When the inlet temperature is very high, the combustion mode does not occur.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.104-109
• /
• 2013

In order to apply nano imprint technology in large area process, roller pressing is promising because of its low cost and high productivity. When pressing mold by roller, liquid resin is locally squeezed between mold and substrate. In this study, the main focus is to understand which process parameter affects residual layer. To do this, a simple analytical model was introduced. Especially, we consider the aspect ratio of patterns as essential cause of variation of the thickness in the equation. As a result, when the aspect ratio of pattern in the mold increases, the thickness of residual layer also increases. In conclusion, we show that the uniformity of residual layer could be accomplished by the control of velocity and pressing force in roller pressing imprint process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.548-551
• /
• 2002

The crystallization of amorphous silicon (a-Si) was achieved using a field aided lateral crystallization (FALC) process at 350 $^{\circ}C$. Under the influence of an electric field, Cu is found to drastically enhance the lateral crystallization velocity of a-Si. When an electric field was applied to the selectively Cu-deposited a-Si film during the heat treatment at temperature as low as 350 $^{\circ}C$, dendrite-shaped crystallization of a-Si progressed toward Cu-free region and the crystallization from negative electrode side toward positive electrode side was accelerated. We identified that 1000${\AA}$ thick a-Si film was completely crystallized by Cu-FALC process at 350 $^{\circ}C$ by TEM analysis.

• International Journal of Fluid Machinery and Systems
• /
• v.10 no.1
• /
• pp.86-98
• /
• 2017

In order to obtain high efficiency and low resistance droplet separation apparatus, axial vane type gas-liquid separators with different guide vanes were designed, and the RNG $k-{\varepsilon}$ model as well as discrete phase model (DPM) were used to investigate the flow pattern inside the separators. It was shown that the tangential velocity distribution under different guide vanes have Rankine vortex characteristics, pressure distribution exhibits a high similarity which value becomes big as the increase of the blade outlet angle and the decrease of the guide vane numbers. The increase of the guide vane numbers and the decrease of the blade outlet angle could make separation improve significantly. The separation efficiency is almost 100% when the droplet diameter is bigger than $40{\mu}m$.

• Journal of the Korean Professional Engineers Association
• /
• v.15 no.2
• /
• pp.3-15
• /
• 1982

The study on prevention measures for vibration and excavation of tunnel for the #3, #4, Seoul Subway. In the Seoul subway tunnel blasting, the drilling pattern and prevention method to seismic vibration are as follows as well as for adaptions of NATM, the supportings of roof and wall holes are arranged with control blasting. 1. The blasting is executed basically using the low velocity explosive such as slurry, Nitrate ammonium explosive, and F-I and F-II explosive for control blasting substituting of existing dynamite. 2. The cut holes are arranged with burn cut pattern and also must be arranged with M/S electrical delay caps substituting of ordinary do]ay caps. 3. Jack leg drills are used in Five Job sites and a jumbo drill in one job site. 4. In performance of safety work and in maintenance of building safety. The drilling length for blasting will not exceed 1.20 meter for round so that the vibration value shall carry below 0.3cm/sec. The harmonizing of better powder, better drilling machine and better technique is only the way of improving tunnelling efficiency and less vibration will help the dereasing of accidence.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.153-157
• /
• 2003

Supersonic and hypersonic aircrafts must pass wide range of speed to reach high speed region. But for existing engines the most efficient operating speed ranges are decided according to their flying speed, so an engine which mixes several engines like TRJ (Turbo Ramjet) and ARJ (Air Turbo Ramjet) has been planed. This mixed type engine has inefficiency that more than two engines must be installed simultaneously, but the pulse detonation engine (PDE) that uses detonation wave has a strong point that it can operate in all speed range with single engine. This paper deals with the simulation of the pulse detonation engine which uses hydrogen peroxide $(H_2O_2)$ mono propellant. Hydrogen peroxide is low-cost propellant, and it is reacted without oxidizer. Comparison between $H_2-O_2$ mixture with $H_2O_2$ mono propellant about thrust, pressure, temperature and velocity shows that $H_2O_2$ is a very useful propellant.

• Journal of the Korean Society of Combustion
• /
• v.22 no.4
• /
• pp.43-50
• /
• 2017

In this study, the multi-environment probability density function(MEPDF) approach has been applied to numerically investigate Delft-Jet-in-Hot-Coflow(DJHC) turbulent flames under Moderate or Intense Low-oxygen Dilution (MILD) combustion condition. Computations are made for two different jet velocities(Re = 4100 and 8800). In terms of mean axial velocity, temperature, and turbulent kinetic energy, numerical results are in reasonably good agreements with experimental data even if there exist the noticeable deviations in downstream region. Based on numerical results, the detailed discussions are made for the essential features of the non-visible flame structure and MILD combustion processes.

• Journal of the Korean Society of Combustion
• /
• v.22 no.4
• /
• pp.35-42
• /
• 2017

This case covers the issues related to the operation problem, cause analysis and improvement cases of the FGD that employed the non-leakage type GGH in coal-fired power plant for the first time in Korea. In the Cooler, there was a main problem that the tube is damaged by the ash cutting due to the high velocity of flue gas in the duct and by the weak wear resistance of material. In the Reheater, there was a main problem that the tube was corroded due to chlorine and sulfur in the circumstance of the low temperature. In order to solve those problems, we have improved the Reheater tube and tube fins by coating enamel to reduce corrosion rate.

• Design & Manufacturing
• /
• v.2 no.1
• /
• pp.39-43
• /
• 2008

There occur not only many problems in the injection process but also low quality productivity due to the injection conditions of various injection factors. Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for the holding pressure affecting cooling time. Results of this study would be helpful to setting of holding pressure for optimization of forming condition in order to reduce cooling time in injection molding.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.10
• /
• pp.982-988
• /
• 2006

The errors of INS (Inertial Navigation System) are known to grow in time. To compensate the accumulated errors, measurements of external or onboard sensors are extensively utilized to form an integrated navigation system. Recently, INS/GPS integrated navigation systems have become popular since exact position and velocity information can be utilized by low cost GPS receivers. Unfortunately, this configuration cannot be trusted at all times especially when there are intentional or unexpected jammings and interruptions. To aid INS irrespectively of these cases, an INS/Image sensor integrated navigation system configuration is designed only based on the information of image sensor gimble angles. The performance of the INS/Image sensor integrated navigation system is evaluated by Monte Carlo simulation.