• 한국염색가공학회지
• /
• 제20권3호
• /
• pp.1-7
• /
• 2008

Three kinds of 135D/108F ITY were produced from raw yam 85D/72F + SDY 50D/36F with. interlacing pressure $1.5kg/cm^2$, $2.5kg/cm^2$, $3.5kg/cm^2$ respectively. 72 kinds of sized yams were manufactured from three ITYs by altering sizing speed, sizing temperature and sizing tension. The mechanical characteristics of 72 kinds of plain fabrics which were woven using the sized yam as a warp were analyzed after scouring. The initial modulus of scoured fabric responded sensitively to the sizing speed in high tension. The WT of scoured fabric recorded the. highest1n the conditions of sizing tension 30g, and air pressure $2.5kg/cm^2$ in interlacing treatment. When sizing temperature was high, the WT value appeared low, but when sizing speed was high, the WT value was much affected by air pressure in interlacing raw yam. The MIU value of fabric according to sizing tension variations increased up to sizing tension 40g, but decreased above it. The bulk density decreased up to sizing tension 30-40g, but increased above it. In addition, the bulk density decreased as sizing temperature increased.

• Steel and Composite Structures
• /
• 제33권6호
• /
• pp.777-792
• /
• 2019

This paper presents a new efficient approach to estimate the S-N type fatigue life assessment curve for S550 high strength steels under low-cycle actions at -60℃. The proposed approach combines a single set of monotonic tension test and one set of fatigue tests to determine the key material damage parameters in the continuum damage mechanics framework. The experimental program in this study examines both the material response under low-cycle actions. The microstructural mechanisms revealed by the Scanning Electron Microscopy (SEM) at the low temperature, furthermore, characterizes the effect due to different strain ratios and low temperature on the low-cycle fatigue life of S550 steels. Anchored on the experimental results, this study validates the S-N curve determined from the proposed approach. The S-N type curve determined from one set of fatigue tests and one set of monotonic tension tests estimates the fatigue life of all specimens under different strain ratios satisfactorily.

• Korean Chemical Engineering Research
• /
• 제52권4호
• /
• pp.516-521
• /
• 2014

고점성이며 낮은 표면장력 매체로 구성된 기포탑에서 축방향 국부 열전달 계수와 총괄 열전달 계수에 대해 고찰하였다. 기체공탑유속(0.02~0.10 m/s), 액체 점도($0.1{\sim}0.3Pa{\cdot}s$) 그리고 액체 표면장력($66.1{\sim}72.9{\times}10^{-3}N/m$)이 국부 및 총괄 열전달 계수에 미치는 영향을 검토하였다. 열전달 영역은 기포탑 내부 열원과 기포탑 간의 열전달계로 구성하였다. 즉, 기포탑의 중앙에 수직 열원을 설치하여 내부 열원으로 하였다. 열전달 계수는 주어진 운전조건에서 열원에 제공되는 열량과 내부 열원과 기포탑 간의 온도차를 연속적으로 측정하여 결정하였다. 국부 열전달 계수는 기체공탑유속이 증가함에 따라 증가하였으나 기체 분산판으로 부터의 축방향 거리가 증가함에 따라, 액체의 표면장력이 증가함에 따라 감소하였다. 총괄 열전달 계수는 기체공탑유속이 증가함에 따라 증가하였으나 액상의 점도와 표면장력이 증가함에 따라서는 감소하였다. 총괄 열전달 계수는 기체공탑유속, 액상의 점도와 표면장력의 함수로 상관계수 0.91의 상관식을 얻을 수 있었으며 넛셀 수, 레이놀즈 수, 플란틀 수 그리고 웨버 수의 함수로 상관계수 0.92의 상관식으로 나타낼 수 있었다. $$h=2502U^{0.236}_{G}{\mu}^{-0.250}_{L}{\sigma}^{-0.028}_L$$ $$Nu=325Re^{0.180}Pr^{-0.067}We^{0.028}$$.

• 설비공학논문집
• /
• 제7권2호
• /
• pp.298-309
• /
• 1995

Low-fin tubes are widely used to enhance condensation heat transfer. In this study, condensation heat transfer experiment was conducted on the low-fin tube using R-11. Three different fin densities-787 fpm (fins per meter), 1102 fpm. 1378 fpm-were tested. The results show that low-fin tube enhances the condensation heat transfer considerablely. The enhancement increases as the fin density increases. It was also found that the fin shape and height have a significant effect on the condensation heat transfer coefficient. Slender or high fins showed a higher condensing heat transfer coefficient compared with fat, low fins. For the tube with 1378 fpm, however, excessive fin height decreased the condensing heat transfer coefficient. The reason may be attributed to the increasing condensate retention angle as the fin density increases. The experimental data are compared with existing prediction models. Results show that Webb's surface tension model predicted the data best (within ${\pm}20%$), which confirms that surface tension plays the major role in low-fin tube condensation.

• 한국운동역학회지
• /
• 제17권3호
• /
• pp.197-207
• /
• 2007

It has been reported that Back-Tension played a significant role in archery (Lee & Bondit, 2005; Kim, 2007) but there are a few researches related Back-Tension in Korea recently. Therefore, the purpose of this study was to investigate archery back tension technique for the second ranked archer in the World and to find ways to improve performance. A subject(height: 185cm, mass: 82kg, years: 21yrs, careers: 12yrs) who is a number of national team and the second ranked archer in the World authorized by FITA (Federation Internationale de Trial Arc) was perticipated in this experiment. When shooting 60 shots($12{\times}5$), shooting motions were recorded with 7 infrared cameras and 2 ultrahigh-speed cameras. A QTM and an Auto Track were used to acquire raw data. The sampling rates of both cameras were 200 Hz. and 1000 Hz. respectively and data were filtered using a fourth order Butterworth low pass filtering with a cutoff-frequency of 30Hz. The parameters were calculated with Matlab6.5 and analyzed with SPSS11.0. After Pearson's correlations between 8 parameters were analyzed, 5 parameters from 13parameters that affected records were analyzed with multiple regression analysis (Enter order: x1, x2, x3, x4, x5). The results were as follows: 1. Comparing between parameters according to scores, the patterns of horizontal and vertical angular velocity(av.) of scapular relative angle was different between 8 score and 9 or 10 scores. 2. The correlations of parameters that affected records were a horizontal av.(x1, p=.032<.05) and a vertical av.(x3, p=.033<.05) of scapular from release to delivery in KB back-tension (anchoring-delivery). 3. The decision coefficients(R2) of above two parameters and three parameters selected by experts that may affect record, that is, an absolute trunk angle(x4) from in KKC back-tension (anchoring-release) and a horizontal relative scapular angle(x2) and an absolute trunk angle(x5) from release to delivery in KB back-tension were 7.7%(x1), 0.1%(x2), 8.5%(x3), 0.7%(x4) and 0.9%(x5) in sequence. 4. The multiple regression equation was a y= -1.16E-2 x1 + 0.109 x2 + 3.437E-2 x3 + 6.139E-2 x4 + 0.117 x5 + 3.420 In conclusion, a total contribution was low, that is, R2(17.9%) suggested that on the one hand, Lim's motion may not depend on a certain factor because his postural factors affected shooting motion are some stable on the other hand, unknown factors may exist(e.g. psychological, physiological factors etc.). Further study of EMG patterns of muscles and anatomic consideration related to shoulder girdle and scapular bones may help to identify mechanism of Back-Tension.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권5호
• /
• pp.120-129
• /
• 2023

행어케이블의 장력은 현수교의 건전성과 안전성을 확인할 수 있는 주요 응답 중 하나이다. 일반적으로 공용 중인 현수교에서 행어케이블의 장력을 추정하기 위해 진동법이 주로 사용되고 있다. 진동법은 행어케이블에서 고유진동수들을 측정하고 행어케이블의 형상 조건을 이용하여 간접적으로 장력을 추정하는 방법이다. 이 연구에서는 영상계측시스템을 이용하여 팔영대교의 행어케이블에 대하여 장력을 추정하였다. 영상계측시스템은 측정의 편의성과 경제성을 고려하여 디지털 캠코더와 삼각대를 사용하였다. 영상계측시스템을 이용하여 측정된 행어케이블의 응답은 변위 기반이므로 진동법을 적용하기 위한 고차모드의 고유진동수는 측정하기 어려울 수 있다. 이 연구에서는 저차모드의 고유 진동수를 이용하여 장력을 추정할 수 있는 역해석 기법을 적용하였다. 역해석 기법은 현장에서 측정된 행어케이블의 고유진동수들과 유한요소해석을 이용하여 산정된 고유진동수들의 오차를 목적함수로 정의하여 최적화를 수행하였다. 최적화 방법은 목적함수의 편미분이 필요 없는 직접탐색법을 적용하였다. 역해석 기법을 이용하여 산정된 장력과 진동법을 이용하여 추정된 장력을 비교 분석하여 역해석 기법에 대한 신뢰도와 정확도를 확인하였다. 그 결과 역해석 기법을 적용하면 저차모드의 고유진동수를 이용하여도 신뢰성 있는 장력의 추정이 가능하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.479-482
• /
• 1999

The tension stiffening effect, which means the maintaining a part of stiffness after cracking of concrete in tensile, exists at a reinforced concrete member because of the concrete softening and bonding stress between cracks. It is required to consider it for precise analysis and evaluation o structural behavior, due to the possibility of discrepancy between the actual behavior and the analysis without considering the tension stiffening effect. Making and adopting a tension stiffening model is the most simple and effective way for considering it at nonlinear analysis which indicated the estimation from models and experimental results were similar each others. The comparisons on RC beam were, also performed in order to analyzed the influence of concrete strength and steel ratio into the structural behavior. They indicated that the results from analysis estimated quite closely to the test results at low steel ratio, however, overestimated at high steel ratio. The overestimation increase linearly as concrete strength or steel ratio increased.

• Tribology and Lubricants
• /
• 제12권4호
• /
• pp.7-12
• /
• 1996

Present study was undertaken to investigate the leakage and friction of self-lubricating piston seal rings. A crank-piston type gas leakage test set-up was constructed. The piston rings were made of PTFE-polyimide composite. The free gap configurations of the seal rings were butt and step types. Eccentric tension rings were used to give the seal rings prepressure between the seal rings and cylinder wall. Two sizes of the tension rings were installed to investigate their effect on the gas leakage and friction of the seal rings. The results showed that step type seal rings are superior than the butt types. High tension spring rings resulted in low leakage and high friction loss. In order to reduce the gas leakage and friction loss of the piston seal rings, there should be compromise between the number of ring stages and prepressure of the tension rings.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.340-343
• /
• 2004

The cement-based composites have been used for construction industry because of their economy, suitability for architecture and structure function, fire resistance, low fee of repair, easiness for acquisition. but the limited strain capacity of these makes them tension-weak, brittle, and considerable notch-sensitive. As one of solution, FRC(fiber reinforced concrete) have been investigated for regulating weakness of the cement-based composites. In these day different fiber types are proposed for better performance such as HFRC(hybrid fiber reinforced concrete). This study shows experimental results to search the ultimate strength, the ultimate mean strain, and the tension toughness of HFRC. The tension toughness is proportional to the amount of steel fiber and carbon fiber. In this experimental program we kept the total of steel fiber and carbon fiber as $1.0\%,\;1.5\%$, respectively.

• 생명과학회지
• /
• 제8권4호
• /
• pp.373-380
• /
• 1998

A considerable change observed in X-ray diffraction during the muscle contraction was that the movement of myosin head and conformational change of contractile monecules were occurred in the muscle contraction. Time slice requires tension peak after the onset of stimulation and the height of tension peak depends on the number of twitch cycle. The intensity of I$_{11}$, I$_{10}$, 143${\AA}$ reflection is measured with 5ms time resolution and is recorded in isometric tension. The peak height of I$_{11}$ and 143${\AA}$ intensity is changed after the onset of a stimulation I$_{i}$, and the length of twitch is shortened by successive twitches in the case of stimulation TI$_{i}$. On the other hand, the peak height of I$_{11}$ and 215${\AA}$ intensity starts to decrease at the 1st twitch and remains constant at low peak hight without appreciable recovery during the contraction term. In the case of uccessive twitch stimulation, the myosin heads of muscle are once moved from their resting position and never returned to their initial position.