Studies on ancient iron production technologies still have challenges to overcome, although there have been many results that have enabled us to understand these old technologies. The purpose of this study is to propose a suitable temperature condition for smelting experiments. The target for reconstruction is a smelting-smithing process in the ancient Jungwon area, and the experiment was designed on the basis of published research, such as archaeological evidence. Experiment A was performed at a low temperature to produce low-carbon iron, while Experiment B was conducted at a relatively high temperature to synthesize high-carbon iron. In addition, the low-carbon iron proved to be suitable for the smithing process. Moreover, aspects such as the microstructure and chemical composition of the slag and the surface condition of the furnace wall showed that the low-temperature smelting process was closer to the ancient method. It is important to mention the premise that the reconstruction of ancient technology can be achieved when the results of an experiment replicate the conditions of a real site. The results show that direct smelting, which produces low-carbon iron bloom under a low-temperature condition, should be the subject of smelting experiments concerning the iron production technologies of the ancient Jungwon area.
$In_{1-x}Ga_xAs$ epitaxial layers were grown at 76 Torr by low pressure metalorganic chemical vapor deposition (LP-MOCVD). Growth rate did not change much with growth temperature. Surface morphology of $In_{1-x}Ga_xAs$ epitaxial layer was affected by lattice mismatch, growth temperature and $AsH_3/(TMIn+TMGa)$ ratio. A high quality epilayer showed a full width at half maximum of 2.8 meV by photoluminescence measurement at 5K. The composition of the $In_{1-x}Ga_xAs$ was determined by the relative gas phase diffusion of TMIn and TMGa. Lattice mismatch and growth temperature were the most important variables that determine the electrical properties of $In_{1-x}Ga_xAs$ epitaxial layers. At optimized growth condition, it was possible to obtain a high quality $In_{1-x}Ga_xAs$ epilayers with a electron concentration as low as $8{\times}10^{14}/cm^3$ and an electron mobility as high as 11,000$\textrm{cm}^2$/Vsec at room temperature.
Kim, Joo-Min;Malintha, G.H.T.;Gunathilaka, G.L.B.E.;Lee, Chorong;Kim, Min-Gi;Lee, Bong-Joo;Kim, Jeong-Dae;Lee, Kyeong-Jun
Fisheries and Aquatic Sciences
/
v.20
no.9
/
pp.20.1-20.8
/
2017
The objective of this study was to examine the effect of dietary supplementation of taurine for juvenile olive flounder (Paralichthys olivaceus) at low water temperature ($16.4{\pm}0.36^{\circ}C$). Fish meal (FM)-based diet was used as the control diet. Four other experimental diets were prepared by adding taurine to FM-based diet at 0.25, 0.50, 1.00, and 1. 50% (T1, T2, T3, and T4, respectively). Each experimental diet was fed to triplicate groups of fish (initial mean body weight, 19.5 g) for 10 weeks. At the end of the feeding trial, growth performance and feed utilization, hematological parameters, non-specific immune responses, whole-body proximate composition, and liver mRNA expression of insulin-like growth factor-1 (IGF-1) were investigated. Feed conversion ratio was significantly reduced while protein efficiency ratio was significantly increased in taurine-supplemented groups. Hematocrit and hemoglobin were also significantly increased while plasma cholesterol levels were decreased in taurine-supplemented groups than those in the control group. Nitroblue-tetrazolium, myeloperoxidase and lysozyme activities, and plasma immunoglobulin level were significantly increased by taurine supplementation. These results suggest that dietary taurine supplementation is effective in improving growth performances, feed utilization, and innate immunity of olive flounder in low water temperature season.
Journal of the Korean Crystal Growth and Crystal Technology
/
v.28
no.1
/
pp.38-43
/
2018
Ceramic membrane has been widely used for water treatment due to its advantages of eco-friendly property and low energy consumption. However, high porosity of ceramic membrane higher than 40 % may cause a problem of strength, when it is applied to a water treatment module. In order to solve this problem, the strength of the membrane edge was improved by using the ceramic glaze. Four different glaze compositions for low temperature sintering was selected to minimize the deformation of the membrane microstructure. After coating with low temperature glaze, cracks were observed due to differences in thermal expansion coefficient between the membrane and glaze. Thus, the thermal expansion coefficient of glaze was controlled by addition of cordierite and petalite. As a results, the compressive strength of the ceramic membrane, which was coated with the optimized glaze composition, was increased from $27N/m^2$ to $117N/m^2$, indicating that the glaze coating can improve the disadvantages of the fragile ceramic membrane.
Journal of the Korean Applied Science and Technology
/
v.39
no.5
/
pp.632-643
/
2022
Although probiotics have been shown to improve health when consumed, recent studies have reported that they can cause unwanted side effects due to bacterial-human interactions. Therefore, the importance of prebiotics that can form beneficial microbiome in the gut has been emphasized. This study isolated and identified bacteria capable of producing biopoymer as a candidate prebiotic from traditional fermented foods. The isolated and identified strain was named WCYSK01 (Wissella sp. strain YSK01). The composition of the medium for culturing this strain was prepared by dissolving 3 g K2HPO4, 0.2 g MgSO4, 0.05 g CaCl2, 0.1 g NaCl in 1 L of distilled water. The LMBP(low molecular weight biopoymers) produced when fermentation was performed with sucrose and maltose as substrates were mainly consisted of DP3 (degree of polymer; isomaltotriose), DP4 (isomaltotetraose), DP5 (isomaltopentaose), and DP6 (isomaltoheptaose). The optimization of LMBP (low molecular weight of biopolymer) production was performed using the response surface methodology. The fermentation process temperature range of 18 to 32℃, the fermentation medium pH in the range of 5.1 to 7.9. The yield of LMBP production by the strain was found to be significantly affected by q fermentation temperature and pH. The optimal fermentation conditions were found at the normal point, and the production yield was more than 75% at pH 7.5 and temperature of 23℃.
$CuInS_2$ thin films were synthesized by sulfurization of Cu/In Stacked elemental layer deposited onto glass Substrates by vacuum furnace annealing at temperature 200[$^{\circ}C$]. And structural and electrical properties were measured in order to certify optimum conditions for growth of the ternary compound semiconductor $CuInS_2$ thin films with non-stoichiometry composition. $CuInS_2$ thin film was well made at the heat treatment 200[$^{\circ}C$] of SLG/Cu/In/S stacked elemental layer which was prepared by thermal evaporator, and chemical composition of the thin film was analyzed nearly as the proportion of 1 : 1 : 2. Physical properties of the thin film were investigated at various fabrication conditions substrate temperature, annealing and temperature, annealing time by XRD, FE-SEM and hall measurement system. At the same time, carrier concentration, hall mobility and resistivity of the thin films was $9.10568{\times}10^{17}$ [$cm^{-3}$], 312.502 [$cm^2/V{\cdot}s$] and $2.36{\times}10^{-2}$ [${\Omega}{\cdot}cm$], respectively.
Boron-phoshor-silicate glass was fabricated on Si substrates by FHD(Flame Hydrolysis Deposition) The microstructrue of silica soot deposited at various conditon such as composition and substrate temperature was analysed by SEM. After consolidation the refractive index and composition of the silica layer were in-vestigated. For refractive index control B, P and Ge were used as additive elements while B and Ge oxides are easily mixed into $SiO_2$, P oxide($B_2O_3$) doping is difficult because of the volatile property due to low melt-ing point. Boron-phosphorous-silicate glass (BPSG) layer were fabricated using bertical torch and optimized flame temperature substrate temperature and distance of torch and substrate. P concentration of BPSG lay-er measured 3.3 Wt% and the consolidation temperature was lower than $1180^{\circ}C$. The measured refractive index of BPSG silica layer in $1.55\;\mu\textrm{m}$ wavelength was $1.4480{\pm}1{\times}10^{-1}$ and the thickness was $22{\pm}1\;\mu\textrm{m}$.
Journal of the Korean institute of surface engineering
/
v.28
no.4
/
pp.207-218
/
1995
Tungsten(W) metal has excellent properties in heat-resistance, corrison-resistance and impact-resistance but W-Metal is hard to sinter because higher than $2,000^{\circ}C$ is required to sinter W-powder. Con-sequently, a deposit technique of Nikel Phosphorus(NiP) on W-powber by the liquid reduction precipitation method was performed. Sintering temperature of the resulting W-NiP composite was lowered around to $1,000^{\circ}C$, and the mechanical properties of the sintered body was studied. The most suitable conditions for NiP thin film deposit on W-Powder by the liquid reduction precipitation method, which are composition, concentration, pH and temperature of the liquid reduction solution, were considered. The activated sintering was carried out in a reducing condition furnace. Components and properties of the sintered body were investigated by the density and the hardness measurements, X- ray diffraction analysis, and microscopic photographs of the surface. Quantity of NiP thin film on W-powder could be varied by the change of the liquid reduction solution composition. The sintering temperature of W-NiP composite powder is lowered to $950^{\circ}C$ from $2,000^{\circ}C$ and the hardness is increased (ca. 720 Hv). Large shrinkage could be observed since density was increased from 5.5 to 11.0 g/$cm^2$ which 86.2% of theoretical density. W metal and $Ni_3P$ crystal were detected through X-ray diffraction on the sintered body. Perfectly activated sintering was observed by microscopic photographs.
Journal of the Korean institute of surface engineering
/
v.34
no.1
/
pp.10-16
/
2001
Recently plasma etching research has been focused on the metal surfaces in the nuclear industry. In this study, surface etching reaction of metallic Co and Mo, principal contaminants in the spent nuclear components, in CF$_4$/O$_2$, gas plasma has been experimentally investigated to look into the applicability and the effectiveness of the technique for the surface decontamination. Experimental variables are $CF_4$/$O_2$ ratio and substrate temperature between 29$0^{\circ}C$ and 38$0^{\circ}C$. Experimental results Show that the optimum gas composition is 80%CF$_4$-20%$O_2$ and the metallic Co and Mo are etched out well enough in the temperatures range. Cobalt starts to be etched above $350^{\circ}C$ and the etching rate increases with increasing substrate temperature. Maximum rate achieved at 38$0^{\circ}C$ under 220 W r.f. plasma power is 0.06 $\mu\textrm{m}$/min. On the other hand, the metallic Mo is etched easily even at low temperature and the reaction rate drastically increases as the substrate temperature goes up. Highest rate obtained under the same conditions is $1.9\mu\textrm{m}$/min. OES (Optical Emission Spectroscopy) analysis reveals that the intensities of F atom and CO molecule reach maximum at the optimum gas composition, which demonstrates that the principal reaction mechanism is fluorination and/or carbonyl reaction. It is confirmed, therefore, that dry processing technique using reactive plasma is quite feasible and applicable for the decontamination of surface-contaminated parts or equipments.
Penkov, O.V.;Plaksin, V. Yu.;Joa, S.B.;Kim, J.H.;LEE, H.J.
Proceedings of the Korean Vacuum Society Conference
/
2010.02a
/
pp.480-480
/
2010
In the present work, we studied effect of the deposition parameters on the structure and properties of ZnO films deposited by DC arc plasmatron. The varied parameters were gas flow rates, precursor composition, substrate temperature and post-deposition annealing temperature. Vapor of Zinc acetylacetone was used as source materials, oxygen was used as working gas and argon was used as the cathode protective gas and a transport gas for the vapor. The plasmatron power was varied in the range of 700-1,500 watts. Flow rate of the gases and substrate temperature rate were varied in the wide range to optimize the properties of the deposited coatings. After deposition films were annealed in the hydrogen atmosphere in the wide range of temperatures. Structure of coatings was investigated using XRD and SEM. Chemical composition was analyzed using x-ray photo-electron spectroscopy. Sheet conductivity was measured by 4-point probe method. Optical properties of the transparent ZnO-based coatings were studied by the spectroscopy. It was shown that deposition by a DC Arc plasmatron can be used for low-cost production of zinc oxide films with good optical and electrical properties. Sheet resistance of 4 Ohms cm was achieved after the deposition and 30 min annealing in the hydrogen at $350^{\circ}C$. Elevation of the substrate temperature during the deposition process up to $350^{\circ}C$ leads to decreasing of the film's resistance due to rearrangement of the crystalline structure.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.