• 한국가스학회지
• /
• 제16권6호
• /
• pp.87-101
• /
• 2012

가스 산업은 고도화와 복잡성으로 인하여 잠재적인 대형사고의 발생위험이 날로 높아가고 있으며, 특히 가연성, 인화성, 폭발성 및 독성물질 등을 대량으로 취급 및 제조함으로써, 사고발생 가능성은 낮지만 일단 사고가 발생하게 되면 사업장 내부의 근로자뿐만 아니라 인근 주민과 환경에 까지 영향을 미치며, 가스제조 시설의 특성상 산업계에 끼치는 파급효과도 매우 크다. 수소가스는 화학 산업 및 산업계 전반에 걸쳐 중요하게 사용되는 기초 원료이며, 특히 2000년 이후 지구온난화가 대두됨에 따라 지구온난화를 방지할 수 있는 대체에너지로 각광 받고 있으나, 분자량이 낮아 다른 가스에 비하여 고압(150 bar.g 이상)으로 실린더 등의 저장용기에 충전하여 사용해야 한다. 수소는 가연성, 폭발성 물질로써 누출(Leakage)로 인하여 화재나 폭발로 이어지는 사고가 많이 발생하고 있다. 이러한 재해를 줄이기 위해서는 단순한 안전관리에서 벗어나 생산 공정중의 잠재위험(Hazard)을 확인하여 기술적으로 평가한 후, 이 결과를 반영하는 체계적인 안전관리 시스템이 필요하다. 본 연구는 산업계 전반에서 사용되고 있는 기초 원료인 가연성, 폭발성의 수소가스 충전시설에 대한 정량적 위험성평가를 실시하였으며, 평가 결과 수소 충전시설에 대한 중요안전요소(EIS, Elements Important for Safety)의 도출 및 이의 효과적 관리방안을 제안하였으며, 사고사례를 통하여 위험성평가 모델의 신뢰성을 검증하였다.

• 한국위험물학회지
• /
• 제2권1호
• /
• pp.18-26
• /
• 2014

We analyzed the demand of competent authorities requiring adequate technical information for initial investigation of chemical accidents. Reflecting technical reports on chemical accident response by environmental agencies in the U.S. and Canada, we presented information on environmental diffusion and toxic effects available for the first chemical accident response. Hydrogen fluoride may have the risk potential to corrode metals and cause serious burns and eye damages. In case of inhalation or intake, it could have severe health effects. The substance itself is inflammable, but once heated, it decomposes producing corrosive and toxic fume. In case of contact with water, it can produce toxic, corrosive, flammable or explosive gases and its solution, a strong acid, may react fiercely with a base. In case of hydrogen fluoride leak, the preventive measures are to decrease steam generation in exposed sites, prevent the transfer of vapor cloud and promptly respond using inflammable substances including calcium carbonate, sodium bicarbonate, ground limestone, dried soil, dry sand, vermiculite, fly ash and powder cement. The method for fire fighting is to suppress fire with manless hose stanchions or monitor nozzles by wearing the whole body protective clothing equipped with over-pressure self-contained breathing apparatus from distance. In case of transport accident accompanied with fire, evacuation distance is 1,600m radius. In cae of fire, fire suppression needs to be performed using dry chemicals, CO₂, water spray, water fog, and alcohol-resistance foam, etc. The major symptoms by exposure route are dyspnoea, bronchitis, chemical pneumonia and pulmonary edema for respiration, skin laceration, dermatitis, burn, frostbite and erythema for eyes, and nausea, diarrhea, stomachache, and tissue destruction for digestive organs. In atmosphere, its persistency is low, and its bioaccumulation in aquatic organism is also low.

• 한국수소및신에너지학회논문집
• /
• 제24권2호
• /
• pp.150-159
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effects of insert geometry and shape of WGS catalysts on CO conversion were measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and WGS catalyst (particle and tablet) and sand were used as bed materials. The parallel wall type and cross type bed inserts were used to hold the WGS catalysts. The CO conversion with steam/CO ratio was determined based on the exit gas analysis. The measured CO conversion using the bed inserts showed high value comparable to physical mixing cases. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. Most of input gas flowed through the catalyst side when we charged tablet type catalyst into the bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. New bed insert geometry was proposed based on the results from this study to enhance contact between input gas and WGS catalyst and $CO_2$ absorbent.

• 동력기계공학회지
• /
• 제20권5호
• /
• pp.86-91
• /
• 2016

This paper is concerned chiefly with the method of porous foam manufacture using basalt stone powder sludge. The hydrogen peroxide($H_2O_2$) of bloating agent has lots of problems to manufacture porous lightweight aggregate due to fast reaction rate with cement or calcium hydroxide($Ca(OH)_2$). The $H_2O_2$ injecting method using nozzle for manufacturing porous lightweight aggregate is proposed, in this study. This method is to inject $H_2O_2$ at the pressure of 10 MPa on upper side of slurry mixing materials such as stone powder sludge and quick-lime(CaO) by injector. The specimen was dried in furnace at $100^{\circ}C$ for 1 hour and cured at ambient temperature for 30 days. We analyzed the characteristics including specific gravity and water absorption. The experiments were found that the porous foam has low specific gravity, high water absorption and uniform distribution of porous more than manufactured foam by general bloating methods.

• 한국전기전자재료학회논문지
• /
• 제24권6호
• /
• pp.468-472
• /
• 2011

Conductive $SrMoO_3$ thin films were fabricated by RF magnetron sputtering with the powder-type sputtering target, and annealed for crystallization. When RTP (rapid thermal processing) in vacuum was applied, the fabricated thin films showed the mixed phases of $SrMoO_3$ and $SrMoO_4$, but $SrMoO_3$ phase could be promoted by the lowering of the working pressure during deposition. In order to eliminate $O_2$ gas during deposition and annealing, further lowering of the working pressure and furnace annealing in hydrogen atmosphere were tried. With the optimization of the deposition and annealing conditions, the thin film with nearly single-phase of $SrMoO_3$ was obtained, and it showed good electrical conduction properties with a low resistivity of $2.5{\times}10^{-3}{\Omega}{\cdot}cm$ at room temperature.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.209-219
• /
• 2006

The supersonic combustion experiments are carried out using T3 free-piston shock tunnel. Different shock tube fill pressures have various inflow conditions. $15^{\circ}$ inclined hydrogen fuel injection is located before the cavity. Oblique shock is generated at the trailing edge of the cavity and reflects off the top and bottom wall. For non-reacting flow, static pressures in low equivalence ratio are similar to those in no fuel injection. As equivalence ratio is increased, static pressures are increased in the duct. In the similar equivalence ratio, static pressures are increased when total enthalpy is decreased. For reacting flow, the flame is occurred near the cavity. The combustion is weak locally in the middle of the duct. The up and down pressure distribution in the duct means that the supersonic combustion is generated.

• 한국가구학회지
• /
• 제19권2호
• /
• pp.106-110
• /
• 2008

This paper investigated and validated the mechanisms and principles for constructing reticular structure of plant fiber through frothing solution approach. After process, plant fibers became low-density reticular-structured block with all properties meeting Chinese standards for cushion packing materials. The bonds between fibers acted as knots in a truss and were strong enough to keep space occupied by bubbles in the frothing solution from shrinking in the subsequent draining process. The formation of the reticular structure depends mainly on the pressure difference between inside and outside bubble, the effect of surface adsorbent force on bubble film, and hydrogen bond among fiber hydroxide.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.609-614
• /
• 2005

Gas hydrates are ice-l ike sol id compounds that are composed of water and natural gas. All common gas hydrates belong to the three crystal structures that are composed of five polyhedral cavities formed by hydrogen bonded water molecules and stable in specific high pressure and low temperature conditions. Gas hydrates contain large amounts of organic carbon and widely occur in deep oceans and permafrost regions, and they may therefore represent a potential energy resource in the future. United States and Japan perform the national R&D programs for the commercial production of gas hydrates in 2010's. The study on gas hydrates are also important for exploration and development of natural gas in the regions where gas hydrates are accumulated and could be formed. Although their global abundance is debated, they play an important role in global climate change since methane is a 50 times more effect ive greenhouse gas than carbon dioxide. Natural gas hydrates also form a possible natural hazard if rapidly dissociated and can cause slides and slumps and in the marine environment associated tsunamis.

• 한국표면공학회지
• /
• 제37권3호
• /
• pp.164-168
• /
• 2004

Polycrystalline silicon thin films were deposited by inductively coupled plasma (ICP) assisted magnetron sputtering using a gas mixture of Ar and $H_2$ on a glass substrate at $250^{\circ}C$. At constant Ar mass flow rate of 10 sccm, the working pressure was changed between 10mTorr and 70mTorr with changing $H_2$ flow rate. The effects of RF power applied to ICP coil and $Ar/H_2$ gas mixing ratio on the properties of the deposited Si films were investigated. The crystallinity was evaluated by both X-ray diffraction and Raman spectroscopy. From the results of Raman spectroscopy, the crystallinity was improved as hydrogen mixing ratio was increased up to$ Ar/H_2$=10/16 sccm; the maximum crystalline fraction was 74% at this condition. When RF power applied to ICP coil was increased, the crystallinity was also increased around 78%. In order to investigate the surface roughness of the deposited films, Atomic Force Microscopy was used.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1988년도 추계학술대회 논문집
• /
• pp.79-81
• /
• 1988

The capacitance-voltage (C-V) characteristics of poly-Si gate MOS devices fabricated by Low-Pressure Chemical Vapor Deposition (LPCVD) system have been studied. In the case poly-Si gate, work function difference and surface state charge density was found lower than that of Al gate. This fact was identified from the C-V curves that flatband shift was shown small due to the hydrogen gas diffused into oxide in processing of alloy and the annealing effect in processing of poly-Si deposition.