• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.6
• /
• pp.15-21
• /
• 2009

The goal of wireless sensor networks is to collect sensing data on specific region over wireless communication. Sink node gathers all local sensing data, processes and transmits them to users who use sensor networks. Generally, senor nodes are low-cost, low power devices with limited sensing, computation and wireless communication capabilities. And sensor network applies to multi-hop communication on large-scale network. As neighboring sensor nodes have similar data, clustering is more effective technique for 'data-aggregation'. In cluster formation technique based on multi-hop, it is necessary that the number of cluster member nodes should be distributed equally because of the balance of cluster formation To achieve this, we propose a method to customize cluster member nodes for energy-efficiency in wireless sensor networks.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.1B
• /
• pp.21-28
• /
• 2011

The femtocell is a miniaturized Base Station (BS) with low-cost and low-power using general broadband access network as backhaul. It is expected not only to improve indoor coverage but also to reduce a service charge. However, in IEEE 802,16e femtocells, when the Mobile Station (MS) scans neighbor BSs for handover, it takes a long time due to too many number of femto BSs. Also the size of the neighbor advertisement message that will be periodically sent by a serving BS is increased as the number of target femto BSs for scanning increases. In this paper, we proposed an efficient femtocell scanning scheme, using a triangulation mechanism and a femto BS monitoring scheme to reduce the number of scanning operations and the size of the neighbor advertisement messages. The proposed scheme can avoid wasting air resources and reduce scanning overheads by minimal scanning operation. The simulation results showed that the proposed scheme could improve scanning performance and avoid wasting air resources, compared with the conventional scheme of the IEEE 802.16e system.

• Journal of Digital Convergence
• /
• v.13 no.7
• /
• pp.207-212
• /
• 2015

The sensor network that is component of the Internet of Things require a lot of research to select the best route to send information to the anchor node, to collect a number of environment and cost efficient for communication between the sensor life. On the sensor network in one of the components of IOT's environment, sensor nodes are an extension device with low power low capacity. For routing method for data transmission between the sensor nodes, the connection between the anchor and the node must be accurate with in adjacent areas relatively. Localization CA (Centroid Algorithm) is often used although an error frequently occurs. In this paper, we propose a range-free localization method between sensor nodes based on the Radical Line in order to solve this problem.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1068-1072
• /
• 2018

In underwater communications, there are many challenges due to energy limitations, long propagation delay, low data rate, and high power loss, unlike terrestrial RF communications. Especially, the propagation delay of underwater acoustic channel is five orders of magnitude higher than in electro-magnetic terrestrial channels due to the low speed of sound(1,500m/s). Thus, the MAC protocols for terrestrial communications are not suitable for underwater network. In this paper, we studied the considerations for MAC protocol in underwater acoustic channel. Here, we concentrated on CSMA based MAC protocols. From the results, we confirmed that the number of control packets has an important effect on the performance in underwater environment. These results would be useful in designing MAC protocols for underwater acoustic communications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.3A
• /
• pp.282-290
• /
• 2006

In this paper, we propose an enhanced Timing Estimator algorithm for 2.45GHz LR-WPAN receiver. Because an expensive and highly efficient oscillator can't be used for low-cost implementation, a Timing Estimator algorithm having stable operation in the channel environment with center frequency tolerance of 80 ppm is required. To enhance the robustness to frequency offset and the stability of receiver performance, multiple delay differential filter is adopted. By utilizing the characteristic that the correlation result between the output signal of Multiple delay differential filter and reference signal is restricted on the In-phase part of the correlator output, a coherent detection scheme instead of the typical noncoherent one is adopted for Timing Estimator. The application of the coherent detection scheme is suitable for LR-WPAN receiver aimed at low-cost, low-power, and low-complexity, since it can remove performance degradation due to squaring loss of I/Q squaring operation and decrease implementation complexity. Computer simulation results show that the proposed algorithm achieved performance improvement compared with the differential detection-based noncoherent scheme by 2dB in average.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.69-77
• /
• 2009

Small size and low profile antenna for mobile vehicular-top-mounted is needed in satellite communication services such as DBS, Satellite Internet and VSAT. In middle latitudes, the development of an array antenna which has the conformal, low profile and 45 degree beam tilted configuration, and has the high gain with sharp beamwidth, low sidelobe and low loss is required for Ka band satellite communication. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level the radiation power control using a design method of the different slot width is proposed. An array antenna consisting of 32 leakywave elements is showing 34.4 dBi of gain, 3.6 degree of beamwidth, below than -25 dB of sidelobe level, 43 degree of beam tilt angle in center frequency 20.0 GHz. Feed network designed by waveguide cooperated feed shows good performance of wideband and low loss.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.8
• /
• pp.2663-2674
• /
• 2014

For cognitive radio sensor networks (CRSNs) that use underlay-based spectrum access, the location of the primary user (PU) plays an important role in the power control of the secondary users (SUs), because the SUs must keep the minimum interference level required by the PU. Received signal strength (RSS)-based localization schemes provide low-cost implementation and low complexity, thus it is suitable for the PU localization in CRSNs. However, the RSS-based localization schemes have a high localization error because they use an inexact path loss exponent (PLE). Thus, applying a RSS-based localization scheme into the PU localization would cause a high interference to the PU. In order to reduce the localization error and improve the channel reuse rate, we propose a RSS-based PU localization scheme that uses distance calibration for CRSNs using underlay model-based spectrum access. Through the simulation results, it is shown that the proposed scheme can provide less localization error as well as more spectrum utilization than the RSS-based PU localization using the mean and the maximum likelihood calibration.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.83-88
• /
• 2001

This paper deals with the economical equipment control which is used by internet network system at the industrial workplace. If the control devices can be accessed by internet, we can have the developed possibility of work conditions. In this paper, we presented the advanced digital timer which has a communication function to control and observe panel to realize control solution based on internet to be easily applicable at workplace with low cost. and we used 485 serial communication module to have parallel expansibility and safety. And, this system was experimented and designed for easy system management and status check from remote station through internet As the result of experiment, the circuit configuration would be more simplified than the existing, and it is expected that multi connection control and monitoring can be simply implemented with low cost equipment at industrial workplace.

• Journal of KIISE:Information Networking
• /
• v.35 no.2
• /
• pp.149-157
• /
• 2008

Since wireless sensor networks consist of nodes with the constrained battery, energy efficient MAC operation is one of the important issues. Low duty cycle operation is critical to conserve energy in wireless sensor network MAC protocol. Some paper proposed a new approach to low power listening, which employs a short preamble to further reduce energy consumption and to reduce latency. But short preamble suffers from unfair channel access problem since there was no consideration for contention between transmission nodes. Preamble counting proposes a solution to each of these problems by employing node selection information. Simulation results show that the preamble counting provides an improved energy efficiency and fairness of packet delivery.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.1 no.2
• /
• pp.104-112
• /
• 2006

ZigBee is the emerging industrial standard for ad hoc networks based on IEEE 802.15.4. It is used for low data rate and low power wireless network applications. Expected applications of ZigBee include wireless sensor networks for remote monitoring, home control, and industrial automation. Since one of the most important design goals of ZigBee is to reduce the installation and running costs, the ZigBee stack is embedded in the cheap and small micro-controller unit. The hierarchical routing algorithm is used for ZigBee end devices which have very limited resources. Using the block addressing scheme, end devices can send data to the destination without a routing table. However, hierarchical routing has the problem that the packets follow the tree hierarchy to the destination even if the destination is located nearby. In this paper, we propose a scheme to improve the hierarchical routing algorithm in ZigBee networks by employing the neighbor table that is originally used together with the routing table. We suggest selecting the neighbor node that has the minimum remaining hops to the destination as the next hop node. Simulation result shows that the proposed scheme saves more than 30% of the hop counts compared with the original hierarchical routing.