• 한국분무공학회지
• /
• 제25권1호
• /
• pp.27-33
• /
• 2020

NOx, PN and CO emissions from diesel trucks make up a significant portion of domestic air pollutant emissions. Therefore, test vehicles with various emission standards and driving modes were selected to evaluate the emission characteristics of regulated pollutants (NOx, PN, CO) in medium-duty trucks. As a result of test, all test vehicles were satisfied with Euro 5 or 6 regulation. NOx emissions of Euro 6 vehicles with after-treatment of LNT + DPF were lower than those of Euro 5 vehicles with DPF. In WLTC mode, all vehicles have high NOx emissions at section of extra high speeds, which are determined by increased fuel consumption and high combustion temperatures. CO and PN emissions from all vehicles were found to be low at section of low speeds. Also, The NO₂/NOx ratio was analyzed at 7-23% in each mode, and the NO₂/NOx ratio increased as the average vehicle speed increased. In NIER 9 mode, the CO, HC, and PN emissions were higher under cold conditions of engine than hot conditions of engine. In addition, vehicles with after-treatment system of LNT have similar NOx emissions level in this study.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.38-43
• /
• 2011

A CNG/diesel dual-fuel engine uses CNG as the main fuel and injects a small amount of diesel as an ignition priming. This study proposed the modification of the existing diesel engine into a dual-fuel engine that injects diesel with a high pressure by common rail direct injection (CRDI) and by injecting CNG at the intake port for premixing. And experiment was progressed for understanding about effect of CNG mixing ratio. The CNG/diesel dual-fuel engine showed equally satisfactory coordinate torque and power regardless of CNG mixing ratio. The PM emission was low at any CNG mixing ratio because of very small diesel pilot injection. In case of NOx and HC, high CNG mixing ratio showed low NOx and HC emissions at low speed. At medium & high speed, low CNG mixing ratio showed low NOx and HC emissions. Therefore, it would be optimized by controlling CNG mixing ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.167-171
• /
• 2001

Air-staging combustion is a relatively well-known technique to reduce NOx emission and used in combination with other techniques nowadays. However, the design variables are still selected depending upon operating circumstances. Though the fuel-rich condition of the primary combustion zone is very helpful to NOx reduction, its range is known to be restricted by the increase of carbon monoxide. However, in many cases carbon monoxide level is so low not to be the restriction at all. So we tried to expand the equivalence ratio range to the richer condition in the primary combustion zone and make the function of each burner component and its contribution to the overall NOx production clear.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.341-342
• /
• 2012

The effect of high ash coal which has relatively high ash content and low combustibility on unburned carbon and NOx emission was experimentally investigated at several excess air ratio and particle size conditions of four coals containing different ash content in a drop tube furnace. Flue gas was measured by Gas analyzer in order to figure out unburned carbon characteristics. The results show that the higher content of ash makes the higher unburned carbon rate, subsequent changes in NOx emission characteristics was investigated.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제25회 KOSCI SYMPOSIUM 논문집
• /
• pp.89-95
• /
• 2002

A hybrid De- NOx technique of non-thermal plasma and $NH_3$ SCR process has been investigated to remove NOx from 300 hp marine engine exhaust under the low temperature conditions, i.e. $100-200^{\circ}C$. Fundamental investigation with Diesel-like simulant gas was also conducted. The performance of the present technique has been demonstrated by treating real diesel exhaust gases, in which high contents of soot, water vapor, $SO_2$, NOx, and unburned HC are included. Detailed engineering data for evaluating the feasibility of the technique are provided in the present investigation.

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.47-56
• /
• 2001

Nitrogen oxides(NOx) and smoke emissions of diesel engine are regarded as a source of air pollution, and there is a global trend to enforce more stringent regulations on these exhaust gas emissions. However, the trade-off relation of NOx and smoke is a main obstacle to reduce both of them simultaneously. In this paper, experiments were conducted with an oxygenated fuel(diethyl ether) as an effective way to improve the trade-off relation of NOx and smoke. Exhaust emissions of diesel fuels with DEE were influenced by the additive content of DEE and the injection timing. Especially, DEE effected more at the high engine speed and load than at the low engine speed and load. Diesel fuel blended with DEE 10% was a desirable blend for the simultaneous reduction of NOx and smoke.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.153-156
• /
• 2008

MILD combustion has been successfully applied to gaseous fuels and few commercial systems are now in operation. Extending MILD combustion applicability to solid fuel of sawdust is the focus of the present work. The MILD combustion furnace at the University of Adelaide in Australia was used in this study. A measurement of $O_2$ and CO emissions have been carried out in parallel with consideration of NOx emission and compared in each modes of conventional natural gas combustion, natural gas MILD combustion, NOx emission in natural gas MILD combustion mode can be reduced to 20% in comparison with conventional combustion. Emission in cases of air carrying sawdust combustion and $CO_2$ carrying sawdust combustion were also compared. Air and $CO_2$ were sued as a carry gas for the sawdust. It was found that MILD conditions are possible for sawdust particles of less than $355{\mu}m$ without additional air pre-heating. It was also found that when using $CO_2$ as the carry gas the flame inside the furnace was not visible anymore and that NOx emission dropped to less than two folds.

• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.211-218
• /
• 1998

The purpose of this study is to investigate the reduction rate of NOX according to several parameters(NOX concentration, the flow rate of gas, the additional amount of C2H4, input voltage, input frequency and so in) when NOX is reduced by using PPCP(Pulse-induced Plasma Chemical Process). PPCP is based on the plasma-chemical technology, which induces narrow voltage pulses to binary electrode structure.

• 대한기계학회논문집B
• /
• 제31권2호
• /
• pp.167-172
• /
• 2007

A new method that optimizes a control of hydrocarbon (HC) addition to diesel exhaust gas for HC type DeNOx catalyst system has been developed. These catalysts are called the HC-DeHOx catalyst in this paper. The system using HC-DeNOx catalyst requires a resonable quantity of hydrocarbons addition in the inlet gas of the catalyst, because the HC concentration in a diesel engine is so low that the HC is not sufficient for NOx conversion. It is expected that this study offers a robust data developing HC injection system.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.76-83
• /
• 2010

Recently, as the current and future emission regulations go stringent, the research of NOx reduction has become a subject of increasing interest and attention in diesel engine. Selective Catalytic Reduction (SCR) is one of the effective technology to reduce NOx emission from diesel engine. Especially, Urea-SCR that uses urea as a reductant is becoming increasingly popular as a cost effective way of reducing NOx emissions from heavy duty vehicles. In this research, we designed urea injector and DCU (Dosing Control Unit) specially developed for controlling the Urea-SCR process onboard vehicles. As passenger and commercial diesel engine experiment, we grasped characteristics of NOx emission and SCR catalyst temperature level in advance. As a result, highest NOx emission level was shown in condition of low engine speed and high load. On the other hand, SCR catalyst temperature was highest at high engine speed and load. On the basis of these result, we conducted the NOx reduction test at steady engine operating conditions using the urea injector and DCU. It was shown that 74% NOx conversion efficiency on the average and 97% NOx conversion efficiency was obtained at high SCR catalyst temperature.