• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.9
• /
• pp.895-902
• /
• 2014

This paper presents a 2-stage CMOS power amplifier for the 1.75 GHz band using a $0.18-{\mu}m$ CMOS process. Using ADS simulation, a power gain of 28 dB and an efficiency of 45 % at an 1dB compression point of 27 dBm were achieved. The implemented CMOS power amplifier delivered an output power of up to 24.8 dBm with a power-added efficiency of 41.3 % and a power gain of 22.9 dB. For a 16-QAM uplink LTE signal, the PA exhibited a power gain of 22.6 dB and an average output power of 23.1 dBm with a PAE of 35.1 % while meeting an ACLR(Adjacent Channel Leakage Ratio) level of -30 dBc.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.374-383
• /
• 2013

This paper presents a design for improvement of isolation characteristics by the inserted stub structure on ground plane of a handy terminal which is composed of a main antenna and a sub antenna covered LTE bandwidth. In order to compensate for a resonance length of proposed antenna and to realize a high isolation characteristic, a pair of stub was inserted and located on ground plane that currents from two antennas were converged. A simulated isolation characteristic of antenna without stub at the LTE class 13 band was about -5 dB, but its characteristics of proposed antenna with two stubs at uplink(777~787 MHz) and downlink(746~756 MHz) of the LTE class 13 band were about -12 dB and -15 dB, respectively. An average gain of a fabricated antenna with two stubs was observed about -2 dBi above and it showed good results with comparison of business condition that the average gain of commercial handy terminal has to appear -4 dBi above. The measured S-parameter characteristics and radiation patterns showed a reasonable agreement with the simulation results.

• Journal of Korean Society for Geospatial Information Science
• /
• v.25 no.1
• /
• pp.3-8
• /
• 2017

In this study future wind resource maps have been produced under climate change scenario using ensemble regional climate model weather research and forecasting(WRF) for the period from 2045 to 2054(mid 21st century). Then various spatiotemporal analysis has been conducted in terms of monthly and diurnal. As a result, monthly variation(monsoon circulation) was larger than diurnal variation(land-sea circulation) throughout the South Korea. Strong wind area with high wind power energy was varied on months and regions. During whole years, strong wind with high wind resource was pronounced at cold(warm) months in particular Gangwon mountainous and coastal areas(southwestern coastal area) driven by strong northwesterly(southwesterly). Projected strong and weak wind were presented in January and September, respectively. Diurnal variation were large over inland and mountainous area while coastal area were small. This new monthly and diurnal variation would be useful to high resource area analysis and long-term operation of wind power according to wind variability in future.

• Journal of the Korean Solar Energy Society
• /
• v.37 no.2
• /
• pp.35-45
• /
• 2017

The types of installation of the photovoltaic system applied to domestic residential buildings are classified as follows: Mounted modules with air circulation, semi-integrated modules with air duct behind, integrated modules with fully insulated back. In order to study generation characteristics of PV system, we verified the validity of interpretation program based on long-term measurement data of demonstration house installed in BAPV form and also analyzed the generation characteristics and performance of each installation type. The results are as follows. First, the RMSE of amount of generation and simulation according to annual daily insolation of demonstration system located in Daejeon was 0.98kWh and the range of relative error of monthly power generation was -5.8 to 3.1. Second, the average annual PR of mounted modules was 82%, semi-integrated modules 76.1% and integrated modules 71.9%. This differences were attributed to temperature loss. Third, the range of operating temperature of annual hourly photovoltaic modules was -6.5 to $61.0^{\circ}C$ for mounted modules, $-6.0{\sim}73.9^{\circ}C$ for semi-integrated modules and -5.5 to $88.9^{\circ}C$ for integrated modules. The temperature loss of each installation type was -14.0 to 16.1%, -13.8 to 21.9%, and -13.6 to 28.5%, respectively.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.18-26
• /
• 2015

In this paper, we proposed and evaluated the performance of an internal MIMO (Multiple Input Multiple Output) antenna for multiband operations including LTE (Long Term Evolution) 700/2300/2500. And to enhance the isolation characteristic, a parasitic element is designed and applied. The proposed single antenna has a volume of $60mm(W){\times}38mm(L)$, and the ground plane is $60mm(W){\times}100mm(L)$. The parasitic element used for enhancing the isolation of the antenna was designed with a copper on FR4 sized $60mm(W){\times}20mm(L){\times}1.6mm(H)$, and the pattern size is $60mm(W){\times}15mm(L)$. Simulated and measured results showed that LTE 700/2300/2500, DCS (Digital Cellular Service: 1710-1880MHz), K-PCS (Korea-Personal Communication Service: 1750-1870MHz), US-PCS (US-Personal Communication Service: 1850-1990MHz), WCDMA (Wideband Code Division Multiple Access: 1920-2170MHz), Wibro (2300-2390MHz), Bluetooth (2400-2483MHz), WLAN (Wireless Local Area Network: 2400-2483.5MHz), US-WiMAX (US-World interoperability for Microwave Access: 2400-2590MHz) frequency bands were covered with $S_{11}$ values less than -6dB (VSWR < 3). Simulated and measured results on $S_{21}$ at 730MHz for the firstly designed MIMO antenna showed -5.50dB and -5.65dB, respectively. When with the parasitic element at the separated ground plane to enhance the isolation performance, -10.33dB and -12.90dB are obtained for the simulation and measurement, so the enhanced isolation performance at lower frequency band (617-867MHz) is confirmed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.447-451
• /
• 2010

We propose an advanced BMPA (balanced multimedia packet allocation) scheme. The proposed scheme considers the optimal resource allocation problem in OFDMA system. When NRT (non-real time), RT (real time), multicast packets arrive at the same time in OFDMA system, the advanced BMPA chooses the best sub-carrier as a multicast channel for multicast packets, gives more weight to RT packets and multicast packets than NRT packets and allocates sub-carriers according to the total weight sum of packets in each user. With simulation results, this paper shows that the advanced BMPA scheme ensures QoS (long-term system throughput and multimedia packet delay) in heterogeneous traffic compared with multicast MU-WF (multi-user water-filling) and BMPA schemes.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.12
• /
• pp.1209-1217
• /
• 2008

For efficient turbid water management a SWAT model was established for the Imha-Andong watershed where serious turbid water problems have frequently occurred. To evaluate soil loss combined with rainfall runoff process, the analysis focused on comparing the daily runoff discharge and concentration of suspended sediment (SS) using measured data sets. The results of annual SS load analysis for each sub-basin using the calibrated model showed that in the entire target watershed the soil loss ranged from 0.7 to 5.9 tons/ha in year 2005 and from 3.0 to 34.0 tons/ha in year 2003 when the typhoon 'Maemi' severly affected the area. In the future, it is suggest to increase model simulation accuracies supported by a long-term and extensive monitoring to enhance basin-wide suspended sediment estimation and management.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.2
• /
• pp.129-136
• /
• 2016

Floating offshore structures keep its position by a mooring system against various kind of environmental loadings. For this reason, a reliable design of the mooring system is a key factor for initial design stage of a floating structure. However, there exists possibility of mooring failure, even the system is designed with enough safety margin, due to the unexpected extreme environmental conditions or long-term fatigue loadings. The breaking of one of the mooring lines may change the tension level of the other mooring lines, which can potentially result in a progressive failure of the entire structure. In this study, time domain numerical simulation of 10MW class wind-wave hybrid platform was carried out with partially broken mooring line. Overall platform responses and variations of the mooring line tension were numerically evaluated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.4
• /
• pp.40-46
• /
• 2006

It is required to develop a highly reliable attitude & orbit control system of satellite that is less expensive as the technology of satellite design & integration is recently matured dramatically. To accomodate this kind of needs, the two axis attitude control method for wheel-based momentum-biased satellite system whose momentum bias vector points to a certain direction(sun direction), is developed using simple but reliable sensors and actuator: three axis magnetometer and coarse sun sensor are used as sensors, and magnetic torque bars are used as actuator. Classical PD type controller design methodologies are applied on a satellite system for the two axis control with the proper assumptions. Nonlinear simulation results are included to demonstrate the long term stability and the performance of closed-loop system design results.

• Journal of Korea Technology Innovation Society
• /
• v.19 no.2
• /
• pp.231-253
• /
• 2016

The purpose of this study is two fold. First, we will explore the meaning, spread effect and consideration factors of manufacturing innovation in terms of theoretical perspective. Second, we will verify the status of high performance computing (HPC) utilization policy, and analyze the situation of US and Korea. Manufacturing innovation policy in each country has the objective in common which aims epoch-making enhancing of productivity. Nevertheless it can be characterized as innovation oriented policy rather than simple trial of productivity improvement. For long term growth and employment, the need for reindustrialization instead of deindustrialization should be recognized. Employment may be decreased temporarily and partially due to manufacturing innovation. However net effect of employment increasing will be bigger because of indirect employment. HPC utilization policy has the importance as a separate movement other than as a subset of manufacturing innovation. US government is trying to eliminate the bottleneck elements in adoption of HPC based M&S activity, and to promote the way of problem solving through the mechanism of public-private partnership, in spite of low level of HPC based M&S. In Korea, ecosystem related with the activity of HPC based M&S is needed, and expansion of M&S utilization in manufacturing companies and fostering of M&S supporting institutions will be important for this task.