• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.186-188
• /
• 1993

This paper reports a status of KLDN(Korean Lightning Detection Network) SYSTEM in Korea, which was constructed by KMA(Korean Meteorological Administration) & KERI(Korean Electrotechnology Research Institute). At first, system configuration was introduced, and then lightning location data between August/1992 & April/1993, which was obtained in KLDN SYSTEM, was analyzed statistically. Finally, we show the future research planning in relation with this KLDN SYSTEM.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.405-407
• /
• 2000

The most generally implemented method to detect the ground speed of the railway vehicles is to use the rotary type speed sensor attached to wheel axle. The Slip or sliding phenomenon on the railway vehicles occurs frequently caused by the weak viscosity of the wheel. Thus, precisely to control the car, the slip/sliding detection system is required. In this paper we proposed for the speed data management system, which uses rotary type speed sensor. Proposed speed management system can detect the slip/sliding with wheel axle as well as correct the generated speed error during in error time, to provide accurate speed and precise location data. The effectiveness for adapting to the railway system is clarified by the computer simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.3
• /
• pp.748-753
• /
• 2004

Edge includes variety of information about image's location and shape etc. So a lot of researches for detecting those edges have been continuing even now and at the early stage of the research, edge detection operators searched neighborhood pixels and used relation among pixels. However, these methods do not have excellent performance in the image which exists noise and can not detect edges selectively. For this reason, in this paper we detected image's line-edge element from degraded image by AWGN (additive white gaussian noise) with wavelet function which is independent of line's width.

• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.686-693
• /
• 2010

In this paper, a fault diagnosis method based on fuzzy logic for the three-parallel power converter in a wind turbine system is presented. The method can not only detect both open and short faults but can also identify faulty switching devices without additional voltage sensors or an analysis modeling of the system. The location of a faulty switch can be indicated by six-patterns of a stator current vector and the fault switching device detection is achieved by analyzing the current vector. A fault tolerant algorithm is also presented to maintain proper performance under faulty conditions. The reliability of the proposed fault detection technique has been proven by simulations and experiments with a 10kW simulator.

• Journal of Information Processing Systems
• /
• v.13 no.6
• /
• pp.1585-1601
• /
• 2017

With the rapid development of computer technologies, a number of image modification methods have emerged, which have great impacts on the security of image information. Therefore, it is necessary to protect the integrity and authenticity of digital images, and digital watermarking technique consequently becomes a research hotspot. An effort is made to survey and analyze advancements of image watermarking algorithms based on singular value decomposition (SVD) in recent years. In the first part, an overview of watermarking techniques is presented and then mathematical theory of SVD is given. Besides, SVD watermarking model, features, and evaluation indexes are demonstrated. Various SVD-based watermarking algorithms, as well as hybrid watermarking algorithms based on SVD and other transforms for copyright protection, tamper detection, location, and recovery are reviewed in the last part.

• Annual Conference of KIPS
• /
• 2019.10a
• /
• pp.795-797
• /
• 2019

In this paper, we propose a method to generate adversarial examples for toxicity detection neural networks. Our dataset is represented by a one-hot vector and we constrain that only one character is allowed to be modified. The location to be changed is founded by the maximum area of input gradient, which represents the most affecting character the model to make decisions. Despite the fact that we have strong constraint compared to the image-based adversarial attack, we have achieved about 49% successful rate.

• Journal of Korea Multimedia Society
• /
• v.24 no.9
• /
• pp.1203-1210
• /
• 2021

In this paper, we developed the inspection system of electric vehicle pouch battery using image processing. Line scan cameras are used for acquiring the all parts of the pouch battery, and several steps of image processing for extracting significant dimensions(User Required Position) of the battery. In image processing, edge lines, node points, dimension lines, etc. were extracted using Preprocessor, Square Edge Detection, and Size Detection algorithms. This is used to measure the dimensions of the location requested by the user on the pouch battery. For verification of the inspection system, the dimensions of three pouch batteries produced in the same process were measured, and the mean and standard deviation were obtained to confirm the precision.

• Journal of Wind Energy
• /
• v.9 no.4
• /
• pp.16-23
• /
• 2018

A damage detection method for the tripod support structure of offshore wind turbines is presented for structural health monitoring. A finite element model of a prototype tripod support structure is established and the modal properties are calculated. The degree and location of the damage are estimated based on the neural network technique using the changes of natural frequencies and mode shape due to the damage. The stress distribution occurring in the support structure is obtained by a dynamic analysis for the wind turbine system to select the output data of the neural network. The natural frequencies and mode shapes for 36 possible damage scenarios were used for the input data of the learned neural network for damage assessment. The estimated damages agreed reasonably well with the accurate ones. The presented method could be effectively applied for damage detection and structural health monitoring of various types of support structures of offshore wind turbines.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3764-3771
• /
• 2021

Based on the convolutional neural network (CNN), a novel technique is investigated for lost gamma source detection in a room. The CNN is trained with the result of a GEANT4 simulation containing a gamma source inside a meshed room. The dataset for the training process is the deposited energy in the meshes of different n-step paths. The neural network is optimized with parameters such as the number of input data and path length. Based on the proposed method, the place of the gamma source can be recognized with reasonable accuracy without human intervention. The results show that only by 5 measurements of the energy deposited in a 5-step path, (5 sequential points 50 cm apart within 1600 meshes), the gamma source location can be estimated with 94% accuracy. Also, the method is tested for the room geometry containing the interior walls. The results show 90% accuracy with the energy deposition measurement in the meshes of a 5-step path.

• Journal of information and communication convergence engineering
• /
• v.20 no.1
• /
• pp.65-72
• /
• 2022

With the mark of the fourth industrial revolution, the smart factory is evolving into a new future manufacturing plant. As a human-machine-interactive tool, augmented reality (AR) helps workers acquire the proficiency needed in smart factories. The valuable data displayed on the AR device must be delivered intuitively to users. Current AR applications used in smart factories lack user movement calibration, and visual fiducial markers for position correction are detected only nearby. This paper demonstrates a marker-based object detection using perspective projection to adjust augmented content while maintaining the user's original perspective with displacement. A new angle, location, and scaling values for the AR content can be calculated by comparing equivalent marker positions in two images. Two experiments were conducted to verify the implementation of the algorithm and its practicality in the smart factory. The markers were well-detected in both experiments, and the applicability in smart factories was verified by presenting appropriate displacement values for AR contents according to various movements.