• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.3
• /
• pp.75-84
• /
• 2013

The seepage quantity analysis of reservoir embankment is very important for assessment of embankment safety. However, the conventional analysis does not consider uncertainty of soil properties. Permeability is known that the coefficient of variation is larger than other soil properties and seepage quantity is highly dependent on the permeability of embankment. Therefore, probabilistic analysis should be carried out for seepage analysis. To designers, however, the probabilistic analysis is not an easy task. In this paper, the method that can be performed probabilistic analysis easily and efficiently through the numerical analysis based commercial program is proposed. Stochastic response surface method is used for approximate the limit state function and when estimating the coefficients, the moving least squares method is applied in order to reduce local error. The probabilistic analysis is performed by LHC-MCS through the response surface. This method was applied to two type (homogeneous, core zone) earth dams and permeability of embankment body and core are considered as random variables. As a result, seepage quantity was predicted effectively by response surface and probabilistic analysis could be successfully implemented.

• Journal of ILASS-Korea
• /
• v.8 no.4
• /
• pp.9-16
• /
• 2003

The Purpose of this study is to investigate the relationships between the local heat release rate and CH concentration have been investigated by numerical simulations of methane-air premixed flames. And simultaneous CH and OH PLIF(Planar Laser Induced Fluorescence) measurement has been also conducted for lean premixed flame as well as for laminar flames. Numerical simulations are conducted for laminar premixed flames and turbulent ones by using PREMIX in CHEMKIN and two dimensional DNS code with GRI mechanism version 2.11, respectively. In the case of laminar premixed flame, the distance between the peak of heat release rate and that of CH concentration is under $91{\mu}m$ for all equivalence ratio calculated in present work. Even for the premixed flame in high intensity turbulence, the distribution of the heat release rate coincides with that of CH mole fraction. For CH PLIF measurements in the laminar premixed flame burner, CH fluorescence intensity as a function of equivalence ratio shows a similar trend with CH mole fraction computed by GRI mechanism. Simultaneous CH and OH PLIF measurement gave us useful information of instantaneous reaction zone. In addition, CH fluorescence can be measured even for lean conditions where CH mole fraction significantly decreases compared with that of stoichiometric condition. It was found that CH PLIF measurements can be applicable to the estimation of the spatial fluctuations of heat release rate in the engine combustion.

• Smart Structures and Systems
• /
• v.16 no.3
• /
• pp.555-577
• /
• 2015

In the work at hand, the development of a morphing flap, actuated through shape memory alloy load bearing elements, is described. Moving from aerodynamic specifications, prescribing the morphed shape enhancing the aerodynamic efficiency of the flap, a suitable actuation architecture was identified, able to affect the curvature. Each rib of the flap was split into three elastic elements, namely "cells", connected each others in serial way and providing the bending stiffness to the structure. The edges of each cell are linked to SMA elements, whose contraction induces rotation onto the cell itself with an increase of the local curvature of the flap airfoil. The cells are made of two metallic plates crossing each others to form a characteristic "X" configuration; a good flexibility and an acceptable stress concentration level was obtained non connecting the plates onto the crossing zone. After identifying the main design parameters of the structure (i.e. plates relative angle, thickness and depth, SMA length, cross section and connections to the cell) an optimization was performed, with the scope of enhancing the achievable rotation of the cell, its ability in absorbing the external aerodynamic loads and, at the same time, containing the stress level and the weight. The conceptual scheme of the architecture was then reinterpreted in view of a practical realization of the prototype. Implementation issues (SMA - cells connection and cells relative rotation to compensate the impressed inflection assuring the SMA pre-load) were considered. Through a detailed FE model the prototype morphing performance were investigated in presence of the most severe load conditions.

• Structural Engineering and Mechanics
• /
• v.37 no.2
• /
• pp.197-213
• /
• 2011

Concrete is a heterogeneous material exhibiting quasi-brittle behaviour. While homogenization of concrete is commonly accepted in general engineering applications, a detailed description of the material heterogeneity using a mesoscale model becomes desirable and even necessary for problems where drastic spatial and time variation of the stress and strain is involved, for example in the analysis of local damages under impact, shock or blast load. A mesoscale model can also assist in an investigation into the underlying mechanisms affecting the bulk material behaviour under various stress conditions. Extending from existing mesoscale model studies, where use is often made of specialized codes with limited capability in the material description and numerical solutions, this paper presents a mesoscale computational model developed under a general-purpose finite element environment. The aim is to facilitate the utilization of sophisticated material descriptions (e.g., pressure and rate dependency) and advanced numerical solvers to suit a broad range of applications, including high impulsive dynamic analysis. The whole procedure encompasses a module for the generation of concrete mesoscale structure; a process for the generation of the FE mesh, considering two alternative schemes for the interface transition zone (ITZ); and the nonlinear analysis of the mesoscale FE model with an explicit time integration approach. The development of the model and various associated computational considerations are discussed in this paper (Part 1). Further numerical studies using the mesoscale model for both quasi-static and dynamic loadings will be presented in the companion paper (Part 2).

• Mineral and Industry
• /
• v.29
• /
• pp.56-66
• /
• 2016

In Korea, where hydrothermal alteration zones are widely distributed, clay veins formed by hydrothermal alteration processes on natural slopes or artificial slopes can play an important role in the slope stability. When the surface water infiltrates the ground where the clay vein exists, the pore water pressure in the ground can be locally increased due to impermeable properties of clay minerals. Infiltration of the surface water induces the increase in the pore water pressure, which can cause erosion of the fine clay particles. The eroded clay particles flow and deposit in an area where the flow velocity is slowed down. Where clay minerals are deposited, ground water can leak due to an increase in local pore pressures, which can cause slope failure. In this paper, studies related to hydrothermal clay vein and landslide are introduced.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.6 no.3
• /
• pp.164-169
• /
• 2004

A spatial interpolation scheme incorporating local geographic potential for cold air accumulation (TOPSIM) was used to test the feasibility of operational frost warning in Chatancheon basin in Yeoncheon County, where the introduction of new crops including temperate zone fruits is planned. Air temperature from April to June 2003 was measured at one-minute intervals at four locations within the basin. Cold-air accumulation potentials (CAP) at 4 sites were calculated for 3 different catchment scales: a rectangular area of 65 x 55 km which covers the whole county, the KOWACO (Korea Water Corporation) hydrologic unit which includes all 4 sites, and the sub-basins delineated by a stream network analysis of the digital elevation model. Daily minimum temperatures at 4 sites were calculated by interpolating the perfect prognosis (i.e., synoptic observations at KMA Dongducheon station) based on TOPSIM with 3 different CAPs. Mean error, mean absolute error, and root mean square error were calculated for 45 days with no precipitation to test the model performance. For the 3 flat locations, little difference was detected in model performance among 3 catchment areas, but the best performance was found with the CAPs calculated for sub-basins at one site (Oksan) on complex terrain. When TOPSIM loaded with sub-basin CAPs was applied to Oksan to predict frost events during the fruit flowering period in 2004, the goodness of fit was sufficient for making an operational frost warning system for mountainous areas.

• Magazine of the Korean Society of Hazard Mitigation
• /
• v.2 no.4 s.7
• /
• pp.40-47
• /
• 2002

Since it is important to understand the bio-climatic change in Seoul for ecological city planning in the future, this paper gives an overview on bio-climate analysis of urban environments at Seoul. We analyzed its characteristics in recent years using the observations of 24 of Automatic Weather Station (AWS) by Korea Meteorological Administration (KMA). In urbanization, Seoul metropolitan area is densely populated and is concentrated with high buildings. This urban activity changes land covering, which modifies the local circulation of radiation, heat and moisture, precipitation and creating a specific climate. Urban climate is evidently manifested in the phenomena of the increase of the air temperature, called urban heat Island and in addition urban sqall line of heavy rain. Since a city has its different land cover and street structure, these form their own climate character such as climate comfort zone. The thermal fold in urban area such as the heat island is produced by the change of land use and the air pollution that provide the bio-climate change of urban eco-system. The urban wind flow is the most important climate element on dispersion of air pollution, thermal effects and heavy shower. Numerical modeling indicates that the bio-climatic transition of wind wake in urban area and the dispersion of the air pollution by the simulations of the wind variation depend on the urban land cover change. The winds are separately simulated on small and micro-scale at Seoul with two kinds of kinetic model, Witrak and MUKLIMO.

• Journal of Environmental Science International
• /
• v.29 no.11
• /
• pp.1099-1108
• /
• 2020

In this study, the capacity of supplying agricultural water to 13 districts was analyzed by calculating the necessary water supply for the arable land of Gunwi-gun and examining the capacity of supplying water to reservoirs, streams, pumping stations, collection sites, and groundwater wells in Gunwi-gun. As a result, among the 13 districts the second district was found to be short of water by 1.2×10⁶ tons/year. In general, local governments establish drought measures by selecting drought disaster risk zones. While selecting drought-risk areas, some water-poor areas that do not have water sources should be selected, even if the entire area has a sufficient water supply. The water-supply evaluation at the regional level was insufficient for locating areas without water sources, but most areas with water sources, such as streams, reservoirs, and pumping stations, were found to have no shortage of water. To locate water shortage areas without water sources, GIS analysis conducted a field survey of areas with a distance of 4 or less than that of water sources analyzed by GIS analysis. Sixty-nine sites in 13 districts were selected for the on-site survey and six areas of water shortage were identified in areas other than the second district.

• Journal of the Korean housing association
• /
• v.22 no.2
• /
• pp.131-139
• /
• 2011

This study is to examine architectural designers' views on the correlations between components and contextual principle of the roadside building facade with the roadside building facade on the border of Asian Culture Center in Gwangju which is expected to undergo a great change by public policies. For setting direction of the roadside building management at the region examined, height of facade, advertisement/signboard, security of continuity through surface pattern management, nodes building, array of height by story, awning/arcade and locality of advertisement/signboard should be induced to design with locality and consideration of local characteristics with silhouette, window and external colors is needed for discrimination from other cities. Regarding the realization method important thing was found that the planning and implementation of architectural design guidelines, architectural aesthetics of the pre-hearing enhancement, active citizen participation, and then additional landscape screening system, incentive schemes, landscape designation of landscape zone was found to be a major realization system.

• Korean Institute of Interior Design Journal
• /
• v.23 no.1
• /
• pp.152-161
• /
• 2014

Beijing, the capital city of China, has gradually increased its amount of culture space and has also introduced a diverse range of cultural facilities to improve the satisfaction of its citizens lives. In particular are its art museums, which are a symbol of the urban culture and enrich the cultural life of its citizens and are also expected to play a role as a psychological pivot point. However, in comparison with the characteristics of various ethics, local, and the influence on the museums of China, studies which analyze the exterior of the art museums are not sufficient. This is because previous research has focused too heavily on the interior of the art museums. This paper aims to derive distinction through the analysis of the exterior of several art museums and present design factors and application methodology. This research looks at art museums in China and analyzes the current state of the art museums that have been developed based on the culture of Beijing. Through analyzing the case study of five art museums that have been selected in Beijing we can improve our understanding of Chinese culture space and derive distinct design factors. Distinct factors in the exterior of art museums include connection, culture, geographic features, public, and creation. This study is expected to contribute to that exterior of the art museum will be as a contact zone to form a spatial connection and a cultural symbol that can reflect Beijing's unique culture characteristics.