• Journal of the Korean Wood Science and Technology
• /
• v.3 no.1
• /
• pp.3-15
• /
• 1975

How to stabilize wood against shrinking and swelling in variable atmospheric moisture conditions is important to the wood-using industry and a challenge to research. Polyethylene glycol stabilize wood by bulking the fiber. PEG also serve as a chemical seasoning agent, suppress decay in high concentrations, and have slight effect on physical properties, gluing or finishing. The study designed to determine the effect of PEG-400 on the dimensional stabilization of local hardwoods for wood carvings that could supply a greatly expanding tourist trade and making curved furniture parts, lamp stands and other decorative objects, and possible gunstock. The species examined were 6 species, Seo-Namoo (Carpinus laxiflora), Cheungcheung-Namoo (Cornus controversa), Gorosae-Namoo (Acer mono), Karae-Namoo (Juglans mandshurica), Jolcham-Namoo (Quercusserrata) and Sanbud-Namoo (Prunus sargentii), used as block of 5cm thick radially to the grain, 7cm wide tangentially, and 70cm long parallel to the wood grain. All these test piecies were conditioned above the fiber saturation point before impregnation. The stabilization effects were determined for PEG-400 treated woods in a 50 percent solution for 20 days. The following conclusions were obtained. PEG retentions increased with treating time. It was more effective to treat at 60$^{\circ}C$ than at room temperature. In degree of PEG-400 impregnation on species, Cheungcheung-Namoo havinglow specific gravity had the highest retentions, 68.77% but the lowest, 56.33% was shown in Jolcham-Namoo with high specific gravity. Specific gravity of treated wood increased considerably with effectiveness of polymer loading. The increases in specific gravity were 5.36 to 13.16 percent. The highest was Jolcham-Namoo, the lowest Karae-Namoo. On the dimensional stability, a 40 percent of effectiveness of polymer loading was just as effective as 60 percent in reduction in water absorptivity (RWA), antishrinkage efficiency (ASE) and antiswelling efficiency (AE), and from over 60 percent they increased more rapidly. Also species response varied considerably. ASE was 30.12 to 69.97 percent tangentially and 27.86 to 56.37 percent radially, AE 34.06 to 73.76 percent tangentially and 30.11 to 70.12 percent radially, and RWA 42.31 to 65.32 percent. No differences in volume swelling among the 6 species were observed. Its values were ranged from 14.98 to 19.55 percent and also increased with PEG retentions. On the mechanical properties, the strengths very much decreased with PEG-400 loadings as shown in Figure 12; that were 11.41 to 22.90 percent in compression, 21.61 to 34.35 percent in bending and 22.83 to 36.83 percent in tensile strength. PEG retention in cell wall was less than 1 percent and the most of PEG were immersed in cell lumen. Except for Korae-Namoo, effectivenesses of polymer loading were as much high as 61.58 to 75.02 percent. This is believed to be due to the effect of PEG-400 on excellant dimensional stability of treated woods.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.88-91
• /
• 2002

The two dimensional size effect of specimen gauge section (length x width) was investigated on the compressive behavior of a T300/924 [45/-45/0/90]3s, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a 30$\times$30, 50$\times$50, 70$\times$70, and 90mm$\times$90mm gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.4
• /
• pp.172-179
• /
• 2014

HEVC (High Efficiency Video Coding) fine-tuned many existing coding tools and adopted also many new coding techniques. As a result, HEVC has accomplished about 2 times of compression efficiency enhancement compared to the existing video coding standard of H.264/AVC. One of the newly adopted tools in HEVC is the transform skip scheme which performs quantization without transform. This technique improves coding efficiency especially with computer-generated images. However, the unavailability of global or local properties of general video signals demands encoder to decide whether performing transform or not for each TU (Transform Unit). The necessity of computing rate-distortion costs for this decision is one reason to increase encoder complexity. In this paper, a fast transform skip mode decision method is proposed, which is based on the fast decision of rate-distortion cost calculation for transform skip mode, by considering frequency characteristics of residual signal. The proposed method can reduce $4{\times}4$ TU encoding time by about 27.1% with only about 0.03% consequential decrement in BDBR.

• International Journal of Highway Engineering
• /
• v.8 no.4 s.30
• /
• pp.115-124
• /
• 2006

The objectives of this paper are to develop the structural condition evaluation technique using Falling Weight Deflectometer deflections and propose the structural condition criteria for asphalt pavements. To figure out correlation between surface deflections and critical pavement responses, the synthetic database has been established using the finite element pavement structural analysis program. A regression approach was adopted to develop the pavement response model that can be used to compute the stresses and strains within pavement structure using the FWD deflections. Based on the pavement response model, the procedure for assessing the structural condition of pavement layers was proposed in this study. To validate the condition evaluation procedure for asphalt pavements, the FWD test, dynamic cone penetrometer test, and repeated triaxial compression test were conducted on 11 sections of national highway and 8 sections of local road. Test results indicate that the tensile strain at the bottom of AC layer and AC elastic modulus were good indicators for estimating the stiffness characteristics of AC layer. For subbase layer, the BDI value and compressive strain on top of the subbase layer were appropriate to predict the structural capacity of subbase layer. The BCI value and compressive strain on top of the subgrade were found to be good indicators for evaluating the structural condition of the subgrade. The evaluation criteria for structural condition in asphalt pavements was also proposed in this paper.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.39 no.2
• /
• pp.186-191
• /
• 2012

The sodium hypochlorite is widely used in endodontic treatment. While it is effective solution for disinfection of root canal system, complications during canal irrigation are rarely reported, especially in primary teeth. This report demonstrates that sodium hypochlorite extruding through the root apex might cause severe complications. A 4-year-old female patient was referred from local dental clinic to the emergency room for the management of sudden facial swelling and pain during re-endodontic treatment of the maxillary primary central incisor using sodium hypochlorite. The patient was given systemic steroids, antihistamines, antibiotics and analgesics and the maxillary primary central incisor was extracted to prevent secondary infection. Swelling began to subside after 2 days. A negative result was obtained from skin patch test with sodium hypochlorite. Thorough care must be taken in primary teeth to prevent the inadvertent injection of sodium hypochlorite to periapical tissues during root canal irrigation. When adverse reaction occurs, proper management such as analgesia, cold compression and adequate medication should be done.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.15 no.3
• /
• pp.3-12
• /
• 2005

This paper introduces a 3D perceptual model based on JND(Just Noticeable Difference) and proposes a video watermarking scheme which is perceptual approach of adaptive embedding in 3D-DCT domain. Videos are composed of consecutive frames with many similar adjacent frames. If a watermark is embedded in the period of similar frames with little motion, it can be easily noticed by human eyes. Therefore, for the transparency the watermark should be embedded into some places where motions exist and for the robustness its magnitude needs to be adjusted properly. For the transparency and the robustness, watermark based on 3D perceptual model is utilized. That is. the sensitivities from the 3D-DCT quantization are derived based on 3D perceptual model, and the sensitivities of the regions having more local motion than global motion are adjusted. Then the watermark is embedded into visually significant coefficients in proportion to the strength of motion in 3D-DCT domain. Experimental results show that the proposed scheme improves the robustness to MPEG compression and temporal attacks by about $3{\sim}9\%$, compared to the existing 3D-DCT based method. In terms of PSNR, the proposed method is similar to the existing method, but JND guarantees the transparency of watermark.

• Journal of Appropriate Technology
• /
• v.6 no.2
• /
• pp.115-125
• /
• 2020

Housing issues such as mushrooming slums remain as chronic in most developing countries. Due to the state's restrained capacity, the housing-vulnerable's self-help approaches have been increasingly inevitable and vital for addressing the housing issues. However, there are still two challenges: securing good quality with economic efficiency, and climate change mitigation and adaptation. This study aims at doing an architectural experiment by developing and educating the production of eco-friendly interlocking stabilized soil bricks (ISSB) by employing vernacular materials and technologies for housing-vulnerable communities in Indonesia. In collaboration with a local architectural NGO, the study features a co-creation workshop in which 40 evicted households participate in the whole process. Soil analysis, mixed design, compression tests, and economic analysis are carried out. This paper illustrates that ISSB also has a high potential as an alternative to a burned brick or a cement block. The application of ISSB to self-help housing is expected to have socioeconomic and environmental effects, thereby facilitating the housing-vulnerable's self-help approaches and contributing to addressing the housing challenges in Indonesia.

• Knowledge Management Research
• /
• v.24 no.1
• /
• pp.147-172
• /
• 2023

This study aims to review the competitiveness of 'TVING', a Korean OTT player in Korean market. For this, this study extracts core business resources of TVING focusing on resource-based theory, and analyzes their competitiveness under VRIO framework. TVING has 4 tangible and intangible resources respectively and 1 human resource. Tangible resources of TVING are technology(recommendation, compression), content(original, exclusive, discriminative non-exclusive), production studio, and paid-subscribers. Intangible resources are content planing capability, distribution network(local, global), marketing promotion·PR, sales), brand preference. And human resource of TVING creates IP professionalism of the company. As a result of VRIO analysis, discriminative non-exclusive content, production studios, and domestic service channels are the most powerful resources of TVING to 'sustain competitive advantage'. Technology, original content, planning capability and IT professionalism bring 'temporary competitive advantage', while exclusive content, the number of paid-subscribers, global service network, and promotion capabilities are not core resources with staying in competitive rank stages. By the way, TVING has potential users for sales of KT and LGU+ thanks to partnership and M&A, but this is not effectively used at the organization level yet. The meaning of this study can be found in that this evaluated competitiveness by each resource of TVING and arranged its implications.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.36 no.3
• /
• pp.193-201
• /
• 2023

In this study, a nonlinear truss finite element is developed to analyze structures with negative Poisson effect-induced tensile buckling. In general, the well-known buckling phenomenon is a stability problem under a compressive load, whereas tensile buckling occurs because of local compression caused by tension. It is not as well-known as classical buckling because it is a recent study. The mechanism of tensile buckling can be briefly explained from an energy standpoint. The nonlinear truss finite element with a torsional spring is formulated because the finite element has not been reported in the literature yet. The post-buckling analysis is then performed using the generalized displacement control method, which reveals that the torsional spring plays an important role in tensile buckling. Structures that mimic a negative Poisson effect can be constructed using such post-buckling behaviors, and one of the possible applications is a mechanical switch. The results obtained are compared to those of analytical solutions and commercial finite element analysis to assess the validity of the proposed finite element model. The numerical results show that the developed finite element model could be a viable option for the basic design of nonlinear structures with a negative Poisson effect.

• Tuberculosis and Respiratory Diseases
• /
• v.62 no.3
• /
• pp.192-196
• /
• 2007

Background: Right middle lobe syndrome (RMLS) is defined as transient or chronic and recurrent atelectasis of the right middle lobe. Although numerous conditions are associated with RMLS, there are very few recent reports in Korea. This study evaluated the causes of RMLS in a local tertiary hospitalover a period of 42 months. Method: Eighty-eight patients (M:F=64:22, mean age: $67.2{\pm}10.3years$), who had consistent chest radiography findings and underwent bronchoscopy in Gyeongsang University Hospital from January 2003 to July 2006, were enrolled in this study. The clinical characteristics and causes of RMLS in these patients were retrospectively reviewed. Results: The most common symptoms fo RMLS were cough, dyspnea and sputum. Tuberculosis was the most common cause (endobronchial tuberculosis in 22 and pulmonary tuberculosis in 1) The other causes were bronchial stenosis by benign fibrotic changes in 22 cases (25%), anthracofibrosis in 13 cases (14.8%), pneumonia in 11 cases (12.5%), lung cancer in 10 cases (11.4%), mucus impaction in 3 cases (3.4%), bronchiectasis in 2 cases (2.3%) and no demonstrable causes in 7 cases (8%). The bronchoscopy findings were mucosal edema with hyperemic changes in 38 cases (43.2%), mucosal edema with anthracotic pigmentation in 16 cases (18.2%), mucus impaction in 13 cases (14.8%), fibrotic stenosis in 13 cases (14.8%), a mass like lesion in 8 cases (9.1%), exudative necrotic material in 4 cases (4.5%), narrowing as a result of extrinsic compression in 2 cases (2.3%) and no demonstrable abnormalities in 12 cases (13.6%). Conclusion: Right middle lobe syndrome was observed more frequently in patients over the age of 65. The causes were mainly benign diseases with endobronchial tuberculosis being the most common.