• Journal of the Korean Geotechnical Society
• /
• 제24권6호
• /
• pp.101-116
• /
• 2008

The use of reinforced earth walls id permanent structures is getting its popularity. Despite a number of advantages of reinforced earth walls over conventional concrete retaining walls, there exists concerns over long-term residual deformations when subjected to repeated and/or cyclic loads, during their service period. In this investigation, the effects of pre-loading in reducing long term residual deformation of reinforced soil structures under sustained and/or repeated loading environment are investigated using a series of reduced-scale model tests. A model pier and a back-to-back (BTB) reinforced soil structures were constructed and tested under various loading and backfilling conditions. The results indicate that the pre-loading technique can be an effective means of controlling residual deformations of reinforced soils under various loading conditions.

• Journal of Environmental Science International
• /
• 제2권4호
• /
• pp.317-324
• /
• 1993

Effluent recycling effect on UASB reactor performances is known as an important operational factor. In the present study, the possibility of intermittent recycle in UASB process for saving the power consumption was examined at different organic loading and various operational modes in recycle time period. The organic removal efficiencies of the reactors operated with the intermittent effluent recycle were considerably higher compared to those without the effluent recycle. In the intermittent recycle mode, the organic removal efficiencies slightly decreased as the non-recycle time period in the operational mode increased. Proper ratio of recycle and non-recycle time period in the mode seemed to be required to prevent the produced biogas from accumulation in the sludge bed, which caused dead zone in the reactor and sludge loss when the gas was escaped from the bed at the certain pressure.

• Journal of Korean Society on Water Environment
• /
• 제24권3호
• /
• pp.297-305
• /
• 2008

It is necessary to select proper reduction methods and to calculate reasonably reduction amount for making good practice of the reduction scheme. Moreover, it is suggested that the reduction amount have to be distributed properly during the planning period. In other words, it has not to be concentrated on the specific year (especially final year of the planning period). The reason why, if the reduction amount concentrate on the final year of the planning period, allotment loading amount could not be achieved in some cases (e.g., insufficiency of budget, extension of construction duration). Even though much of the budget have been supported from national treasury (about 50%), it is thought the role of the local government must be strengthened gradually.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제24권9호
• /
• pp.1264-1276
• /
• 2000

Light-off catalyst has been used for minimization of cold-start emissions. Improved cold-start performance of light-off catalyst needs the optimal design in terms of flow distribution, geometric surface area, precious metal loading, cell density and space velocity. In this study, these influential factors are numerically investigated using integrated numerical technique by considering not only 3-D fluid flow but also heat and mass transfer with chemical reactions. The present results indicate that uneven catalyst loading of depositing high active catalyst at upstream of monolith is beneficial during warm-up period but its effect is severely deteriorated when the space velocity is above 100,000 $hr^{-1}$ To maximize light-off performance, this study suggests that 1) a light-off catalyst be designed double substrate type; 2) the substrate with high GSA and high PM loading at face be placed at the front monolith; and 3) the cell density of the rear monolith be lower to reduce the pressure drop.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 한국경영과학회/대한산업공학회 2005년도 춘계공동학술대회 발표논문
• /
• pp.592-598
• /
• 2005

The port, differently from general working places, is a closed area required for security, customs, and quarantine procedures. The loading and unloading is being done differently by ports, cargoes, and ships. To do loading and unloading, a lot of equipment and different types of labor are required, which flow is complicated and safe management is essential. As above mentioned the port is very unique and very deteriorated working place in its working environment. The purpose of this study is to propose ways to reduce and prevent from port accidents. As first step to do this, we have collected 923 accidents happened at Incheon Port during the period of 1994 to 2003. We have thoroughly analyzed characteristics, harmfulness, and risk of the loading/unloading they have done, as well as the accident frequency and relationship between the accidents. As second step to further analyze, We have employed DMAIC technology, an advanced process of 6 sigma presently in spotlight as the best program for management innovation. This analysis results in recognition of important accident characteristics, causes and effects analysis, critical causes of accident, and suggestions to decrease accidents.

• The Journal of Korean Physical Therapy
• /
• 제17권1호
• /
• pp.108-122
• /
• 2005

The gait training strategy in very important things for central nervous system(CNS) injury patients. There are many method and strategy for regaining of the gait who had CNS injury. A human being has central pattern generator(CPG) is spinal CPG for locomotion. It is a neural network which make the cyclical patterns and rhythmical activities for walking. Sensory input from loading and hip position is essential for CPG stimulation that makes the central neural rhythm and pattern generating structure. From sensory input, the proprioceptive information facilitate proximal muscles that controlled in voluntarily from cortical level and visual and / or acoustical information facilitate distal muscles that controlled voluntarily from subcortical level. Gait training method can classify that is functional level and structural level. Functional level includ level surface gait, going up and down the stair. It is important to facilitate a guide tempo in order to activate the central pattern generators. During the functional test or functional activities, can point out the poor period in gait that have to be facilitate in structural level. There are many access methods with patient position and potentiality. The methods are using of rhythmic initiation, replication and combination of isotonic with standing position. Clinically using it on weight transfer onto the stance leg, loading response, loading response and pre-swing, terminal stance, up and downwards stairs.

• Proceedings of the Korean Geotechical Society Conference
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.58-65
• /
• 2004

Recently, the top & down method with drilled shafts as a foundation of high rise building is often adopted for the purpose of construction period reduction and construction cost effectiveness. It is common to omit the loading test as a Quality assurance on account of the high capacity of drilled shafts for the top & down method. It seems that the capacity of drilled shaft in recent top & down method is beyond that of conventional loading test method.However, the quality assurance for the drilled shaft as foundation of high rise building becomes much more important since the drilled shaft should bear much higher working load. It may be a small scale test pile could be an alternative as a quality assurance for the drilled shaft with high capacities. Through a case study, this paper gives an idea for solving the limitation of the conventional loading test method for the quality assurance of drilled shaft with high capacities. In particular, this paper analyzed the scale effect for a small drilled shaft installed into bedrock, which could be used for an alternative.

• Proceedings of the KSR Conference
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.30-34
• /
• 2007

Structural integrity of railway vehicles should last for a long period against various and continuous fatigue loadings, and the carbody structures of railway vehicle are manufactured by applying multiform welding types for each material. Since the most of cracks are occurred and proceeded at the vicinity of welding area during the lifetime of carbody structure, the fatigue strength evaluation for welding area of carbody structure should have been carried out. Rotem Company has evaluated lifetime and fatigue strength of carbody structure according to the fatigue analysis based on the international standard and/or inner-official regulation. This study introduces the fatigue analysis method that we have evaluated and calculated the damages for the welding areas of carbody structure under various fatigue loading conditions using cumulative fatigue damage rule(Miner's rule) to verify whether the cumulative damage does exceed unity. This study contains the fatigue test of specimens to derive stress-life relations(S-N curve), sub-modeling analysis and the calculation of cumulative damages under fatigue loading. The fatigue analysis verifies the welding area shall be capable of withstanding under fatigue loading, identifies how critical area shall be selected and presents the principles to be used for design verification.

• Proceedings of the Safety Management and Science Conference
• /
• 대한안전경영과학회 2005년도 춘계학술대회
• /
• pp.199-212
• /
• 2005

Many countries of the world is driving forward development of large-scale hub port. They are now pushing ahead with setting up of effective marketing strategies to survive in keen competitions of the 21st century port industry. The port is of ever increasing importance for the bridge connecting sea and road transportation in handling international cargoes. The port, differently from general working places, is a closed area required for security, customs, and quarantine procedures. The loading and unloading is being done differently by ports, cargoes, and ships. To do loading and unloading, a lot of equipment and different types of labor are required, which flow is complicated and safe management is essential. As above mentioned the port is very unique and very deteriorated working place in its working environment. The purpose of this study is to propose ways to reduce and prevent from port accidents. As first step to do this, we have collected 923 accidents happened at Incheon Port during the period of 1994 to 2003. We have thoroughly analyzed characteristics, harmfulness, and risk of the loading/unloading they have done, as well as the accident frequency and relationship between the accidents. As second step to further analyze, We have employed DMAIC technology, an advanced process of 6 sigma presently in spotlight as the best program for management innovation. This analysis results in recognition of important accident characteristics, causes and effects analysis, critical causes of accident, and suggestions to decrease accidents.

• Journal of the Korea Safety Management & Science
• /
• 제7권2호
• /
• pp.13-27
• /
• 2005

Many countries of the world is driving forward development of large-scale hub port. They are now pushing ahead with setting up of effective marketing strategies to survive in keen competitions of the 21st century port industry. The port is of ever increasing importance for the bridge connecting sea and road transportation in handling international cargoes. The port, differently from general working places, is a closed area required for security, customs, and quarantine procedures. The loading and unloading is being done differently by ports, cargoes, and ships. To do loading and unloading, a lot of equipment and different types of labor are required, which flow is complicated and safe management is essential. As above mentioned the port is very unique and very deteriorated working place in its working environment. The purpose of this study is to propose ways to reduce and prevent from port accidents. As first step to do this, we have collected 923 accidents happened at Incheon Port during the period of 1994 to 2003. We have thoroughly analyzed characteristics, harmfulness, and risk of the loading/unloading they have done, as well as the accident frequency and relationship between the accidents. As second step to further analyze, We have employed DMAIC technology, an advanced process of 6 sigma presently in spotlight as the best program for management innovation. This analysis results in recognition of important accident characteristics, causes and effects analysis, critical causes of accident, and suggestions to decrease accidents.