• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.157-164
• /
• 2001

This paper performs static and dynamic tests of a multi-leaf spring and a tapered leaf spring to investigate their hysteretic characteristics. In the static test, trapezoidal input load is applied with 0.1Hz excitation frequency and with zero initial loading conditions. In the dynamic test, sinusoidal input load is applied with five excitation amplitudes and three excitation frequencies. In these tests, static and dynamic hysteretic characteristics of the multi-leaf spring and the tapered leaf spring are compared, and, the effects of excitation amplitudes and frequencies on dynamic spring rate are also shown. In this paper, actual vehicle tests are performed to study the effects of hysteretic characteristics of the large-sized truck's handling performance. The multi-leaf spring or the tapered leaf spring is used in the front suspension. The actual vehicle test is performed in a double lane change track with three velocities. Lateral acceleration, yaw rate and roll angle are measured using a gyro-meter located at the mass center of the cab. The test results showed that a large-sized truck with a tapered leaf spring needs to have an additional apparatus such as roll stabilizer bar to increase the roll stabilizer due to hysteretic characteristics.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1272-1275
• /
• 2007

The HDD (hard disk drive) using Load/Unload (L/UL) technology includes the benefits which are increased areal density, reduced power consumption and improved shock resistance than those of contact-start-stop (CSS). Dynamic L/UL has been widely used in portable hard disk drive and will become the key technology for developing the small form factor hard disk drive. Main design objectives of the L/UL mechanisms are no slider-disk contact or no media damage even with contact during L/UL, and a smooth and short load and unload process. In this paper, we focus on state matrix, pitch static attitude (PSA), roll static attitude (RSA), loading/unloading contour (LC/ULC), impact force and contact. Stability of slider is mainly determined by PSA and RSA. State matrix by PSA and RSA is also important indicator. Therefore we analyze state matrix of SFF HDD suspension through the LC/ULC.

• Journal of Welding and Joining
• /
• v.25 no.1
• /
• pp.63-69
• /
• 2007

Once assessment of material failure characteristics is captured precisely in a unified way, it can bedirectly incorporated into the structural failure assessment under various loading environments, based on the theoretical backgrounds so called Local Approach to Fracture. The aim of this study is to develop a numerical fatigue test method by continuum damage mechanics applicable for the assessment of structural integrity throughout crack initiation and structural failure based on the Local Approach to Fracture. The generalized elasto-visco-plastic constitutive equation, which can consider the internal damage evolution behavior, is developed and employed in the 3-D FEA code in order to numerically evaluate the material and/or structural responses. Explicit information of the relationships between the mechanical properties and material constants, which are required for the mechanical constitutive and damage evolution equations for each material, are implemented in numerical fatigue test method. The material constants selected from constitutive equations are used directly in the failure assessment of material and/or structures. The performance of the developed system has been evaluated with assessing the S-N diagram of stainless steel materials.

• Journal of Korean Society on Water Environment
• /
• v.26 no.5
• /
• pp.816-821
• /
• 2010

It has been achieved 109.1 kg/d of BOD reduction that is equivalent to the amount of BOD loading discharged from 21,880 persons and dramatic decrease of the fallout ratio against water quality of effluent, from 42% to 9%, through technical support on ISTPs to be applied by the ISMSGA at the upper area of Geongan river in Yong-In city. It was clearly revealed that the most efficient configuration for ISTP was a series of anaerobic tank, equalization basin, aerobic tank, sedimentation tank, and then effluent tank. Also, the major causes on the fallout ratio of ISTP resulted in the lack of management (67.5%) and imperfect facilities (32.5%). Then, when compared the quantity of water supply with the design capacity of ISTP, the design capacity was estimated as 1.8 or 2.4 folds larger than the real quantity of water supply so that it is essential to punctually consider the key factors such as an estimation methods, the specificity of commission operator and construction by high systematic technologies to improve the water quality for the future.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.2
• /
• pp.219-230
• /
• 2010

Computer simulation has been widely used to design and optimize the operation of wastewater treatment plants since 1980. For secondary clarifiers, the simulation has been a tool to optimize the performance by providing dimensions for flocculation well. However, there has been no attempt to find the optimized geometrical parameters in circular secondary clarifier using simulation tools. In this study, three SVIs (Sludge Volume Indexes), two well types (feed and flocculation wells), 8 SWDs (Side Water Depths) and 9 bottom slopes were variables for simulation. Diurnal inflow and associated MLSS (Mixed Liquor Suspended Solid) concentrations were used for input loadings. When flocculation well was installed, 48% less concentration at lowest ESS (Effluent Suspended Solid) concentrations was produced and the diurnal ESS concentration range had been reduced by 52%. From these results, flocculation well must be installed to produce lower and stable ESS from circular secondary clarifiers. Under same loading conditions with $300m{\ell}$/g of SVI, The lowest ESS was produced when SWD was 4.5m with 4% of bottom slope. Therefore, SWD and bottom slope must not be deeper than 4.5m and must be near 4%, respectively, in circular clarifier with flocculation well to produce the lowest ESS concentration.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.3
• /
• pp.315-322
• /
• 2007

The purpose of this study was to investigate the biodegradability and performance of organic removal and methane production rate when treating piggery wastewater using a granule of two-phase anaerobic process applied UASB. BMP test was conducted as simple means to monitor relative biodegradability of substrate and to determine methane production of an organic material. The two-phase anaerobic process is consisted of a continuous flow stirred-tank reactor (CFSTR) for the acidification phase and an Upflow Anaerobic Sludge Blanket reactor (UASB) for the methanogenesis. The acidogenic reactor played key roles in reducing the periodically applied shock-loading and in the acidification of the influent organics. A stable maximum biogas production rate was 400mL. The methane contents ranged from 73 to 80% during the experimental period. It is known that most of the removed organic matter was converted to methane gas, and the produced biogas might be high quality for its subsequent use.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.704-709
• /
• 2014

In this study, we fabricated a novel micro porous hybrid scaffold of biphasic calcium phosphate (BCP) and a polylectrolyte complex (PEC) of chitosan (CS) and hyaluronic acid (HA). The fabrication process included loading of CS-HA PEC in a bare BCP scaffold followed by lypophilization. SEM observation and porosimetry revealed that the scaffold was full of micro and macro pores with total porosity of more than 60 % and pore size in the range of $20{\sim}200{\mu}m$. The composite scaffold was mechanically stronger than the bare BCP scaffold and was significantly stronger than the CS-HA PEC polymer scaffold. Bone morphogenetic growth factor (BMP-2) was immobilized in CS-HA PEC in order to integrate the osteoinductive potentiality required for osteogenesis. The BCP frame, prepared by sponge replica, worked as a physical barrier that prolonged the BMP-2 release significantly. The preliminary biocompatibility data show improved biological performance of the BMP-2 immobilized hybrid scaffold in the presence of rabbit bone marrow stem cells (rBMSC).

• International Journal of Concrete Structures and Materials
• /
• v.4 no.2
• /
• pp.77-87
• /
• 2010

Prestressed concrete (PSC) I-type girders have been used for span length around up to 40 m in domestic region. PSC girders are very cost effective girder type and extending their lengths more than 50 m will bring large benefit in cost. A new design method was proposed by combining two notable design concept in order to extend the applicable span length in this study. First of all, several numbers of openings was introduced in the girder web, and half of the anchorage devices were moved into the openings. In this way, large compressive stress developed at end zone was reduced, and the portion of design load coming from self-weight was reduced as well. Secondly, prestressing force was introduced in the girder not once at the initial stage, but through multiple loading stages. A full scale girder with the length of 50 m with the girder depth of 2 m was fabricated, and a flexural test was conducted in order to verify the performance of newly developed girder. Test results showed that the new holed web design concept can provide a way to design girders longer than 50 meters with the girder height of 2 m.

• Journal of Biosystems Engineering
• /
• v.35 no.1
• /
• pp.53-63
• /
• 2010

The performance of two serial completely stirred tank reactors (CSTRs) for treatment of swine manure (SM) with Chinese cabbage silage (CCS) was studied. The two CSTRs of 41 liters each were connected in series and first reactor was fed swine manure with Chinese cabbage silage in 3:1 proportion by VS basis. The FOS/TAC, methane content (%) and pH were utilized as the parameters for the digester stability control. The FOS/TAC value was found to be effective indicator for instant digester condition. The stability of reactors can be obtained with the FOS/TAC value up to 1.0 with accumulation of FOS value below 10,000 mg/L. Material exchange method was effective in transferring the excess volatile fatty acids (VFA) from the first reactor to the second one and maintaining stability in both the reactors. The biogas yield and the methane yield was 0.55-0.61 and 0.41-0.42 L/g VS fed, respectively, at organic loading rate (OLR) of 2.2-2.6 g VS/L with total HRT of 32 days.

• Journal of Korea Multimedia Society
• /
• v.14 no.1
• /
• pp.103-111
• /
• 2011

Legacy Java card which adapts a Java platform loads and executes an application when electronics power is provided. However, recently the most Java cards are embedded into a mobile terminal as USIM cards, therefore the power is continually provided for the smart cards. In this case, operation of a Java card system needs to consider its operating system to be advanced in memory management, object management and transaction mechanism. In this paper, we present a high performance Java Card system which is able to have efficient installation, loading and execution of application by applying a new memory management of the smart card that has safe power system.